/* This project is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. Multiprotocol is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with Multiprotocol. If not, see . */ // This module makes it possible to bind to and control the IKEA "Ansluta" line // of remote-controlled lights. // To bind, first switch the receiver into binding mode, then the TX. // Once bound, the TX can send one of three commands: // lights off, lights dimmed 50% and lights on. // Those are mapped to throttle ranges 0..0x55, 0x56..0xAA, 0xAB..0xFF. #if defined(IKEAANSLUTA_CC2500_INO) #include "iface_cc2500.h" #define IKEAANSLUTA_BIND_COUNT 30 // ~ 2sec autobind/65ms per loop = 30 binding packets // Commands #define IKEAANSLUTA_LIGHT_OFF 0x01 #define IKEAANSLUTA_LIGHT_DIM 0x02 // 50% dimmed light #define IKEAANSLUTA_LIGHT_ON 0x03 #define IKEAANSLUTA_PAIR 0xFF void IKEAANSLUTA_send_command(uint8_t command){ CC2500_Strobe(CC2500_SIDLE); packet[4] = option; packet[5] = command; CC2500_WriteData(packet, 8); } uint16_t IKEAANSLUTA_callback(void) { if (bind_counter) { IKEAANSLUTA_send_command(IKEAANSLUTA_PAIR); if(--bind_counter == 0) { BIND_DONE; CC2500_SetPower(); } } else { uint8_t throttle = convert_channel_8b(THROTTLE); uint8_t cmd = throttle <= 0x55 ? IKEAANSLUTA_LIGHT_OFF : throttle <= 0xAA ? IKEAANSLUTA_LIGHT_DIM : IKEAANSLUTA_LIGHT_ON; IKEAANSLUTA_send_command(cmd); } return 65535; // 65ms loop cycle is more than enough here (we could make it even longer if not for uint16_t) } // Register initialization values as a continuous memory block (to save on flash memory) const PROGMEM uint8_t IKEAANSLUTA_init_values[] = { 0xFF, // CC2500_06_PKTLEN 0x04, // CC2500_07_PKTCTRL1 0x05, // CC2500_08_PKTCTRL0 0x00, // CC2500_09_ADDR (unused, default) 0x10, // CC2500_0A_CHANNR 0x09, // CC2500_0B_FSCTRL1 0x00, // CC2500_0C_FSCTRL0 0x5D, // CC2500_0D_FREQ2 0x93, // CC2500_0E_FREQ1 0xB1, // CC2500_0F_FREQ0 0x2D, // CC2500_10_MDMCFG4 0x3B, // CC2500_11_MDMCFG3 0x73, // CC2500_12_MDMCFG2 0xA2, // CC2500_13_MDMCFG1 0xF8, // CC2500_14_MDMCFG0 0x01, // CC2500_15_DEVIATN 0x07, // CC2500_16_MCSM2 0x30, // CC2500_17_MCSM1 0x18, // CC2500_18_MCSM0 0x1D, // CC2500_19_FOCCFG 0x1C, // CC2500_1A_BSCFG 0xC7, // CC2500_1B_AGCCTRL2 0x00, // CC2500_1C_AGCCTRL1 0xB2, // CC2500_1D_AGCCTRL0 0x87, // CC2500_1E_WOREVT1 (unused, default) 0x6b, // CC2500_1F_WOREVT0 (unused, default) 0xf8, // CC2500_20_WORCTRL (unused, default) 0xB6, // CC2500_21_FREND1 0x10, // CC2500_22_FREND0 0xEA, // CC2500_23_FSCAL3 0x0A, // CC2500_24_FSCAL2 0x00, // CC2500_25_FSCAL1 0x11, // CC2500_26_FSCAL0 0x41, // CC2500_27_RCCTRL1 0x00, // CC2500_28_RCCTRL0 }; void IKEAANSLUTA_init(void) { if (IS_BIND_DONE) bind_counter = 0; else bind_counter = IKEAANSLUTA_BIND_COUNT; // All packets we send are the same packet[0] = 0x06; packet[1] = 0x55; packet[2] = 0x01; // Bytes 3&4 are the transmitter address (to which the RX binds) // Byte 5 is the command. packet[3] = rx_tx_addr[3]; // + // packet[4] = option; // packet[5] = 0x00; // Command goes here packet[6] = 0xAA; packet[7] = 0xFF; // Configure & initialize CC2500 for (uint8_t i = 0; i <= CC2500_28_RCCTRL0-CC2500_06_PKTLEN; ++i) CC2500_WriteReg(CC2500_06_PKTLEN+i, pgm_read_byte_near(&IKEAANSLUTA_init_values[i])); CC2500_SetTxRxMode(TX_EN); CC2500_SetPower(); } #endif