Lua Generateur

SERIAL

. . . . .

FLYSKY

Extended limits supported
Note that the RX ouput will be AETR.

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	CH5	CH6	CH7	CH8	Reset/Bind

FLYSKY

V9X9

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	Reset/Bind

FLYSKY

V6X6

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH14

A

E

T

R

FLIP

LIGHT

PICTURE

VIDEO

HEADLESS

RTH

XCAL

YCAL

Reset/Bind

FLYSKY

V912

CH1	CH2	CH3	CH4	CH5	CH6	CH14
A	E	T	R	BTMBTN	TOPBTN	Reset/Bind

HUBSAN

H107

Models: Hubsan H102D, H107/L/C/D and Hubsan H107P/C+/D+
Autobind protocol
Telemetry enabled for battery voltage and TX RSSI
Option=vTX frequency (H107D) 5645 - 5900 MHz

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	HEADLESS	Reset/Bind

HUBSAN

H301

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	LED	STAB	RTH	VIDEO	Reset/Bind

HUBSAN

H501

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH0

CH14

A

E

T

R

FLIP

LIGHT

RTH

VIDEO

HEADLESS

GPS_HOLD

ALT_HOLD

SNAPSHOT

---

Reset/Bind

FRSKYD

. . . . .

Modèle : FrSky receivers D4R and D8R. DIY RX-F801 and RX-F802 receivers.
Option : fine frequency tuning. This value is different for each board. To determine the option value, find the two limits where the RX loses connection then set the option value to half way between them. If you have a 4in1 V2 board the value is around 40.
Extended limits supported
Telemetry enabled for A0, A1, RSSI, TSSI and Hub

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8
---	---	---	---	---	---	---	---

Close

HISKY

GYRO: -100%=6G, +100%=3G

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	GEAR	PITCH	GYRO	CH8	Reset/Bind

Close

HISKY

HK310

Modèle : RX HK-3000, HK3100 and XY3000 (TX are HK-300, HK-310 and TL-3C)

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH0	CH14
			T	R	AUX	T_FSAFE	R_FSAFE	AUX_FSAFE	Reset/Bind

Close

V2X2

. . . . .

Modèle : WLToys V202/252/272, JXD 385/388, JJRC H6C, Yizhan Tarantula X6 ...
PICTURE: also automatic Missile Launcher and Hoist in one direction
VIDEO: also Sprayer, Bubbler, Missile Launcher(1), and Hoist in the other dir

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	HEADLESS	MAG_CAL_X	MAG_CAL_Y	Reset/Bind

Close

DSM

DSM2_22

Extended limits supported
Telemetry enabled for TSSI and plugins
option=number of channels from 4 to 12. An invalid option value will end up with 6 channels.
Notes:
- model/type/number of channels indicated on the RX can be different from what the RX is in fact wanting to see. So don't hesitate to test different combinations until you have something working. Using Auto is the best way to find these settings.
- RX ouput will always be TAER independently of the input AETR, RETA...
DSM2, Resolution 1024, refresh rate 22ms

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12
A	E	T	R	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12

Close

DSM

DSM2_11

DSM2, Resolution 2048, refresh rate 11ms

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12
A	E	T	R	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12

Close

DSM

DSMX_22

DSMX, Resolution 2048, refresh rate 22ms

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12
A	E	T	R	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12

Close

DSM

DSMX_11

DSMX, Resolution 2048, refresh rate 11ms

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12
A	E	T	R	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12

Close

DSM

AUTO

The "AUTO" feature enables the TX to automatically choose what are the best settings for your DSM RX and update your model protocol settings accordingly.
The current radio firmware which are able to use the "AUTO" feature are ersky9x (9XR Pro, 9Xtreme, Taranis, ...) and er9x for M128 (9XR) and M2561.
For these firmwares, you must have a telemetry enabled TX and you have to make sure you set the Telemetry "Usr proto" to "DSMx".
Also on er9x you will need to be sure to match the polarity of the telemetry serial (normal or inverted by bitbashing), while on ersky9x you can set "Invert COM1" accordinlgy.

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12
A	E	T	R	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH12

Close

DEVO

. . . . .

Extended limits supported
Note that the RX ouput will be EATR.
Bind procedure using serial:
- With the TX off, put the binding plug in and power on the RX (RX LED slow blink), then power it down and remove the binding plug. Receiver should now be in autobind mode.
- Turn on the TX, set protocol = Devo with option=0, turn off the TX (TX is now in autobind mode).
- Turn on RX (RX LED fast blink).
- Turn on TX (RX LED solid, TX LED fast blink).
- Wait for bind on the TX to complete (TX LED solid).
- Make sure to set the RX_Num value for model match.
- Change option to 1 to use the global ID.
- Do not touch option/RX_Num anymore.
Bind procedure using PPM:
- With the TX off, put the binding plug in and power on the RX (RX LED slow blink), then power it down and remove the binding plug. Receiver should now be in autobind mode.
- Turn on RX (RX LED fast blink).
- Turn the dial to the model number running protocol DEVO on the module.
- Press the bind button and turn on the TX. TX is now in autobind mode.
- Release bind button after 1 second: RX LED solid, TX LED fast blink.
- Wait for bind on the TX to complete (TX LED solid).
- Press the bind button for 1 second. TX/RX is now in fixed ID mode.
- To verify that the TX is in fixed mode: power cycle the TX, the module LED should be solid ON (no blink).
- Note: Autobind/fixed ID mode is linked to the dial number. Which means that you can have multiple dial numbers set to the same protocol DEVO with different RX_Num and have different bind modes at the same time. It enables PPM users to get model match under DEVO.

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	CH5	CH6	CH7	CH8	Reset/Bind

Close

YD717

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

YD717

SKYWLKR

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

YD717

SYMAX4

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

YD717

XINXUN

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

YD717

NIHUI

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

KN

WLTOYS

Dual Rate: +100%=full range, Throttle Hold: +100%=hold, Idle Up: +100%=3D, GYRO: -100%=6G, +100%=3G

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH14
A	E	T	R	DR	THOLD	IDLEUP	GYRO	Ttrim	Atrim	Etrim	Reset/Bind

Close

KN

FEILUN

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH14
A	E	T	R	DR	THOLD	IDLEUP	GYRO	Ttrim	Atrim	Etrim	Reset/Bind

Close

SYMAX

Autobind

Modèle : Syma X5C-1/X11/X11C/X12

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP		PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

SYMAX

SYMAX5C

Autobind

Model: Syma X5C (original) and X2

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP		PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

SLT

. . . . .

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH14
A	E	T	R	GEAR	PITCH	Reset/Bind

Close

CX10

GREEN

Autobind

Modèle : Cheerson CX-10 green pcb
Extended limits supported
Rate: -100%=rate 1, 0%=rate 2, +100%=rate 3

CH1	CH2	CH3	CH4	CH5	CH6	CH14
A	E	T	R	FLIP	RATE	Reset/Bind

Close

CX10

BLUE

Autobind

Modèle : Cheerson CX-10 blue pcb & some newer red pcb, CX-10A, CX-10C, CX11, CX12, Floureon FX10, JJRC DHD D1
Rate: -100%=rate 1, 0%=rate 2, +100%=rate 3 or headless for CX-10A

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	FLIP	RATE	PICTURE	VIDEO	Reset/Bind

Close

CX10

DM007

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	MODE	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

CX10

Q282

Autobind

Model: JXD 509 is using Q282 with CH12=Start/Stop motors

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH14

A

E

T

R

FLIP

LED

PICTURE

VIDEO

HEADLESS

RTH

XCAL

YCAL

Reset/Bind

Close

CX10

JC3015_1

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	FLIP	MODE	PICTURE	VIDEO	Reset/Bind

Close

CX10

JC3015_2

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	FLIP	MODE	LED	DFLIP	Reset/Bind

Close

CX10

MK33041

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH14
A	E	T	R	FLIP	MODE	PICTURE	VIDEO	HEADLESS	RTH	Reset/Bind

Close

CX10

Q242

Autobind

Model: JXD 509 is using Q282 with CH12=Start/Stop motors

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH14

A

E

T

R

FLIP

LED

PICTURE

VIDEO

HEADLESS

RTH

XCAL

YCAL

Reset/Bind

Close

CG023

Autobind

Modèle : EAchine CG023/CG031/3D X4

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LIGHT	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

CG023

YD829

Autobind

Modèle : Attop YD-822/YD-829/YD-829C ...

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP		PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

CG023

H8_3D

Autobind

Modèle : EAchine H8 mini 3D, JJRC H20/H22
JJRC H20: OPT1=Headless, OPT2=RTH
JJRC H22: OPT1=RTH, OPT2=180/360Â° flip mode
H8 3D: OPT1=RTH then press a direction to enter headless mode (like stock TX), OPT2=switch 180/360Â° flip mode
CAL: calibrate accelerometers

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LIGTH	OPT1	OPT2	CAL	Reset/Bind

Close

BAYANG

. . . . .

Autobind

Modèle : EAchine H8(C) mini, BayangToys X6/X7/X9, JJRC JJ850, Floureon H101 ...

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH14
A	E	T	R	FLIP	RTH	PICTURE	VIDEO	HEADLESS	INVERTED	Reset/Bind

Close

FRSKYX

CH_16

Modèle : FrSky receivers X4R, X6R and X8R.
Option : fine frequency tuning. This value is different for each board. To determine the option value, find the two limits where the RX loses connection then set the option value to half way between them. If you have a 4in1 V2 board the value is around 40.
Extended limits supported
Telemetry enabled for A1 (RxBatt), A2, RSSI, TSSI and Hub

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH13

CH14

CH15

CH16

---

----

Close

FRSKYX

CH_8

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8
---	---	---	---	---	---	---	---

Close

ESKY

. . . . .

CH1	CH2	CH3	CH4	CH5	CH6	CH14
A	E	T	R	GYRO	PITCH	Reset/Bind

Close

MT99XX

MT99

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LED	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

MT99XX

H7

Autobind

Modèle : Eachine H7, Cheerson CX023

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LED	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

MT99XX

YZ

Autobind

Model: Yi Zhan i6S
Only one model can be flown at the same time since the ID is hardcoded.

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	LED	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

MT99XX

LS

Autobind

Modèle : LS114, 124, 215

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	INVERT	PICTURE	VIDEO	HEADLESS	Reset/Bind

Close

MJXQ

WLH08

Autobind

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH13

CH14

A

E

T

R

FLIP

LED

PICTURE

VIDEO

HEADLESS

RTH

AUTOFLIP

PAN

TILT

Reset/Bind

Close

MJXQ

X600

Autobind

Only 3 TX IDs available, change RX_Num value 0..2 to cycle through them

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH13

CH14

A

E

T

R

FLIP

LED

PICTURE

VIDEO

HEADLESS

RTH

AUTOFLIP

PAN

TILT

Reset/Bind

Close

MJXQ

X800

Autobind

Only 3 TX IDs available, change RX_Num value 0..2 to cycle through them

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH13

CH14

A

E

T

R

FLIP

LED

PICTURE

VIDEO

HEADLESS

RTH

AUTOFLIP

PAN

TILT

Reset/Bind

Close

MJXQ

H26D

Autobind

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH13

CH14

A

E

T

R

FLIP

LED

PICTURE

VIDEO

HEADLESS

RTH

AUTOFLIP

PAN

TILT

Reset/Bind

Close

MJXQ

E010

Autobind

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH13

CH14

A

E

T

R

FLIP

LED

PICTURE

VIDEO

HEADLESS

RTH

AUTOFLIP

PAN

TILT

Reset/Bind

Close

SHENQI

. . . . .

Autobind

Model: Shenqiwei 1/20 Mini Motorcycle
Throttle +100%=full forward,0%=stop,-100%=full backward.

CH1	CH2	CH3	CH4	CH14
		T	R	Reset/Bind

Close

FY326

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	HEADLESS	RTH	Calibrate	Expert	Reset/Bind

Close

FY326

FY319

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	HEADLESS	RTH	Calibrate	Expert	Reset/Bind

Close

SFHSS

. . . . .

Modèle : Futaba RXs and XK models.
Option : fine frequency tuning. This value is different for each board. To determine the option value, find the two limits where the RX loses connection then set the option value to half way between them. If you have a 4in1 V2 board the value is around 40.
***

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	CH5	CH6	CH7	CH8	Reset/Bind

Close

J6PRO

. . . . .

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH14

---

Reset/Bind

Close

FQ777

. . . . .

Model: FQ777-124

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	FLIP	RTH	HEADLESS	EXPERT	Reset/Bind

Close

ASSAN

. . . . .

Extended limits supported
The transmitter must be close to the receiver while binding.

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH14
---	---	---	---	---	---	---	---	---	---	Reset/Bind

Close

FRSKYV

. . . . .

Modèle : FrSky receivers V8R4, V8R7 and V8FR.
Option : fine frequency tuning. This value is different for each board. To determine the option value, find the two limits where the RX loses connection then set the option value to half way between them. If you have a 4in1 V2 board the value is around 40.
Extended limits supported

CH1	CH2	CH3	CH4
---	---	---	---

Close

HONTAI

Autobind protocol

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH14
A	E	T	R	FLIP	LED	PICTURE	VIDEO	HEADLESS	RTH	CAL	Reset/Bind

Close

HONTAI

JJRCX1

CH1	CH2	CH3	CH4	CH6	CH0	CH14
A	E	T	R	ARM		Reset/Bind

Close

HONTAI

X5C1

X5C1 clone

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH11	CH14
A	E	T	R	FLIP	LED	PICTURE	VIDEO	HEADLESS	RTH	CAL	Reset/Bind

Close

HONTAI

FQ777

Format FQ777-951C

CH1	CH2	CH3	CH4	CH6	CH7	CH8	CH9	CH14
A	E	T	R	FLIP	SNAPSHOT	VIDEO	HEADLESS	Reset/Bind

Close

OPENLRS

. . . . .

Empty protocol

Close

JOYSWAY

. . . . .

CH1	CH2	CH3	CH4	CH14
A	E	T	R	Reset/Bind

Close

WK2X01

WK2801

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
---	---	---	---	---	---	---	---	Reset/Bind

Close

WK2X01

WK2601

Option:
0 = 5+1
2 = 6+1
..1 = HÃ©licoptÃ¨re (. = autres options pour ce mode)
.01 = HÃ©licoptÃ¨re normal
.11 = HÃ©licoptÃ¨re avec pit inversÃ©
0.1 = Pitch curve -100
1.1 = Pitch curve 100
CONF: Option 1 = Rate Throtle
Option 2 = Pitch

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH14
---	---	---	---	---	---	---	Reset/Bind

Close

WK2X01

WK2401

CH1	CH2	CH3	CH4	CH14
---	---	---	---	Reset/Bind

Close

SKYARTEC

. . . . .

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH14
?	?	?	?	?	?	?	Reset/Bind

Close

UDI

U816_V1

Modele: Known UDI 2.4GHz protocol variants, all using BK2421
* UDI U819 coaxial 3ch helicoper
* UDI U816/817/818 quadcopters
- "V1" with orange LED on TX, U816 RX labeled '' , U817/U818 RX labeled 'UD-U817B'
- "V2" with red LEDs on TX, U816 RX labeled '', U817/U818 RX labeled 'UD-U817OG'
- "V3" with green LEDs on TX. Did not get my hands on yet.
* U830 mini quadcopter with tilt steering ("Protocol 2014")
* U839 nano quadcopter ("Protocol 2014")
Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH14
A	E	T	R	FLIP 360	FLIP	VIDEO	LED	MODE 2	---	Reset/Bind

Close

UDI

U816_V2

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH14
A	E	T	R	FLIP 360	FLIP	VIDEO	LED	MODE 2	---	Reset/Bind

Close

UDI

U839_2014

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH9	CH10	CH14
A	E	T	R	FLIP 360	FLIP	VIDEO	LED	MODE 2	---	Reset/Bind

Close

FBL100

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
?	?	?	?	?	?	?	?	Reset/Bind

Close

FBL100

HP100

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
?	?	?	?	?	?	?	?	Reset/Bind

Close

HM830

. . . . .

Modele: HM Hobby HM830 RC Paper Airplane
Autobind

CH1	CH2	CH3	CH4	CH5	CH14
A	Turbo	T	Trim	Bouton	Reset/Bind

Close

CFLIE

. . . . .

Modele: CrazyFlie Nano quad
Autobind

CH1	CH2	CH3	CH4	CH14
A	E	T	R	Reset/Bind

Close

H377

. . . . .

CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8	CH14
A	E	T	R	CH5	CH6	CH7	CH8	Reset/Bind

Close

ESKY150

. . . . .

Autobind

CH1	CH2	CH3	CH4	CH14
A	E	T	R	Reset/Bind

Close

BLUEFLY

. . . . .

Autobind

CH1	CH2	CH3	CH4	CH5	CH6	CH14
A	E	T	R	GEAR	PITCH	Reset/Bind

Close

NE260

. . . . .

Modele: Nine Eagles SoloPro
Autobind

CH1	CH2	CH3	CH4	CH14
A	E	T	R	Reset/Bind

Close

AFHDS2A

. . . . .

Telemetry enabled for battery voltage and TX RSSI
Option= 0-PWM_IBUS 1-PPM_IBUS 2-PWM_SBUS 3-PPM_SBUS

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH13

CH14

CH15

T

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

CH13

CH14

Failsave T

Close

INAV

. . . . .

En cours de passage

CH14

Reset/Bind

Close

LUA Script Close

-- Protocol Selected
local PROTO_PAGE = 0
local CONFIRMATION_PAGE = 1

-- Navigation variables
local page = PROTO_PAGE
local dirty = true
local edit = false
local field = 0
local fieldsMax = 0

-- Model settings
local ProtoId = 01
local ProtoSub = 0
local ProtoSubNb = 0

-- Common functions
local lastBlink = 0
local function blinkChanged()
  local time = getTime() % 128
  local blink = (time - time % 64) / 64
  if blink ~= lastBlink then
    lastBlink = blink
    return true
  else
    return false
  end
end

local function fieldIncDec(event, value, max, force)
  if edit or force==true then
    if event == EVT_PLUS_BREAK then
      value = (value + max)
      dirty = true
    elseif event == EVT_MINUS_BREAK then
      value = (value + max + 2)
      dirty = true
    end
    value = (value % (max+1))
  end
  return value
end

local function valueIncDec(event, value, min, max)
  if edit then
    if event == EVT_PLUS_FIRST or event == EVT_PLUS_REPT then
      if value < max then
        value = (value + 1)
        dirty = true
      end
    elseif event == EVT_MINUS_FIRST or event == EVT_MINUS_REPT then
      if value > min then
        value = (value - 1)
        dirty = true
      end
    end
  end
  return value
end

local function navigate(event, fieldMax, prevPage, nextPage)
  if event == EVT_ENTER_BREAK then
    edit = not edit
    dirty = true
  elseif edit then
    if event == EVT_EXIT_BREAK then
      edit = false
      dirty = true  
    elseif not dirty then
      dirty = blinkChanged()
    end
  else
    if event == EVT_PAGE_BREAK then     
      page = nextPage
      field = 0
      dirty = true
    elseif event == EVT_PAGE_LONG then
      page = prevPage
      field = 0
      killEvents(event);
      dirty = true
    else
      field = fieldIncDec(event, field, fieldMax, true)
	end
  end
end

local function getFieldFlags(position)
  flags = 0
  if field == position then
    flags = INVERS
    if edit then
      flags = INVERS + BLINK
    end
  end
  return flags
end

local function channelIncDec(event, value)
  if not edit and event==EVT_MENU_BREAK then
    servoPage = value
    dirty = true
  else
    value = valueIncDec(event, value, 0, 15)
  end
  return value
end

-- Init function
local function init()
end

-- Protocol Menu
local ProtoItems = 
{"FLYSKY","HUBSAN","FRSKYD","HISKY","V2X2","DSM","DEVO","YD717","KN","SYMAX","SLT","CX10","CG023","BAYANG","FRSKYX","ESKY","MT99XX","4","MJXQ","SHENQI","FY326","SFHSS","J6PRO","FQ777","ASSAN","FRSKYV","HONTAI","OPENLRS","JOYSWAY","WK2X01","SKYARTEC","UDI","FBL100","HM830","CFLIE","H377","ESKY150","BLUEFLY","NE260","AFHDS2A","INAV"}
local
 SubProtoItemsA = {"FLYSKY","V9X9","V6X6","V912"}
local SubProtoItemsB = {"H107","H301","H501"}
local SubProtoItemsC = {"HISKY","HK310"}
local SubProtoItemsD = {"DSM2_22","DSM2_11","DSMX_22","DSMX_11","AUTO"}
local SubProtoItemsE = {"YD717","SKYWLKR","SYMAX4","XINXUN","NIHUI"}
local SubProtoItemsF = {"WLTOYS","FEILUN"}
local SubProtoItemsG = {"SYMAX","SYMAX5C"}
local SubProtoItemsH = 
{"GREEN","BLUE","DM007","Q282","Q242","JC3015_1","JC3015_2","MK33041"}
local SubProtoItemsI = {"CG023","YD829","H8_3D"}
local SubProtoItemsJ = {"CH_16","CH_8"}
local SubProtoItemsK = {"MT99","H7","YZ","LS"}
local SubProtoItemsL = {"WLH08","X600","X800","H26D","E010"}
local SubProtoItemsM = {"FY326","FY319"}
local SubProtoItemsN = {"HONTAI","JJRCX1","X5C1","FQ777"}
local SubProtoItemsO = {"WK2801","WK2401","WK2601"}
local SubProtoItemsP = {"U816_V1","U816_V2","U839_2014"}
local SubProtoItemsQ = {"FBL100","HP100"}

local function drawEngineMenu()
  lcd.clear()
  lcd.drawText(1, 0, "What do you want ?", 0)
  lcd.drawFilledRectangle(0, 0, LCD_W, 8, GREY_DEFAULT+FILL_WHITE)
  lcd.drawNumber(12, 10, ProtoId, getFieldFlags(0)) 
  lcd.drawLine(LCD_W/2-10, 8, LCD_W/2-10, LCD_H, DOTTED, 0)
  lcd.drawText(17, 10, ProtoItems[ProtoId+1], 0)
  
  if ProtoId == 0 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 3
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsA[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsA
  elseif ProtoId == 1 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 2
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsB[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsB
  elseif ProtoId == 2 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 3 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 1
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsC[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsC
  elseif ProtoId == 4 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 5 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 4
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsD[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsD
  elseif ProtoId == 6 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 7 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 4
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsE[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsE
  elseif ProtoId == 8 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 1
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsF[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsF
  elseif ProtoId == 9 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 1
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsG[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsG
  elseif ProtoId == 10 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 11 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 7
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsH[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsH
  elseif ProtoId == 12 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 2
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsI[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsI
  elseif ProtoId == 13 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 14 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 1
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsJ[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsJ
  elseif ProtoId == 15 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 16 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 3
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsK[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsK
  elseif ProtoId == 179999999999 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 17 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 4
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsL[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsL
  elseif ProtoId == 18 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 19 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 1
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsM[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsM
  elseif ProtoId == 20 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 21 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 22 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 23 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 24 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 25 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 3
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsN[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsN
  elseif ProtoId == 26 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 39 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 40 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 2
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsO[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsO
  elseif ProtoId == 41 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 43 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 2
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsP[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsP
  elseif ProtoId == 44 then
    ProtoSub = 0
    fieldsMax = 1
    ProtoSubNb = 1
    lcd.drawNumber(12, 20, ProtoSub, getFieldFlags(1))
    lcd.drawText(17, 20, SubProtoItemsQ[ProtoSub+1], getFieldFlags(1))
    SubProtoItems = SubProtoItemsQ
  elseif ProtoId == 49 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 50 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 51 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 52 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 53 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 54 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 55 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  elseif ProtoId == 56 then
    ProtoSub = 0
    fieldsMax = 0
    ProtoSubNb = 0
    SubProtoItems = {""}
  end
end
local function engineMenu(event)
  if dirty then
    dirty = false
    drawEngineMenu()
  end

navigate(event, fieldsMax, page, page+1)

if field==0 then
    ProtoId = fieldIncDec(event, ProtoId, 39)
  elseif field==1 then
    ProtoSub = fieldIncDec(event, ProtoSub, ProtoSubNb)
  end
end

-- Confirmation Menu
local function drawNextLine(x, y, label, channel)
  lcd.drawText(x, y, label, 0);
  if channel ~= nil then
	lcd.drawSource(x+52, y, MIXSRC_CH1+channel, 0)
  end
  y = y + 8
  if y > 50 then
    y = 12
    x = 120
  end
  return x, y
end
local function drawConfirmationMenu()
  local x = 22
  local y = 12
  lcd.clear()
  lcd.drawText(48, 1, "Install switch?", 0);
  lcd.drawFilledRectangle(0, 0, LCD_W, 9, 0)
    x, y = drawNextLine(x, y, "Protocol: "..ProtoItems[ProtoId+1], nil)
	x, y = drawNextLine(x, y, "Sub-Protocol: "..SubProtoItems[ProtoSub+1], 
nil)
  lcd.drawText(48, LCD_H-8, "[Enter Long] to confirm", 0);
  fieldsMax = 0
end

local function applySettings()
--  model.defaultInputs()
--  model.deleteMixes()
  if ProtoId == 0 then
    if ProtoSub == 0 then	--proto FLYSKY 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto V9X9 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto V6X6 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="XCAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="YCAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="", source=92,
 weight=100, multiplex=ADD })
    end
    if ProtoSub == 3 then	--proto V912 
      model.insertMix(4, model.getMixesCount(4), { name="BTMBTN", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="TOPBTN", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 1 then
    if ProtoSub == 0 then	--proto H107 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto H301 
      model.insertMix(4, model.getMixesCount(4), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="STAB", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto H501 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="GPS_HOLD", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="ALT_HOLD", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="SNAPSHOT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="", source=92,
 weight=100, multiplex=ADD })
      model.insertMix(13, model.getMixesCount(13), { name="Reset/Bind", 
source=92, weight=100, multiplex=ADD })
    end
  elseif ProtoId == 2 then
    if ProtoSub == 0 then	--proto FRSKYD 
      model.insertMix(4, model.getMixesCount(4), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="---", 
source=92, weight=100, multiplex=ADD })
    end
  elseif ProtoId == 3 then
    if ProtoSub == 0 then	--proto HISKY 
      model.insertMix(4, model.getMixesCount(4), { name="GEAR", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="PITCH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="GYRO", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto HK310 
      model.insertMix(4, model.getMixesCount(4), { name="R", source=4, 
weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="AUX", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="T_FSAFE", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="R_FSAFE", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 4 then
    if ProtoSub == 0 then	--proto V2X2 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="MAG_CAL_X", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="MAG_CAL_Y", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="", source=92,
 weight=100, multiplex=ADD })
    end
  elseif ProtoId == 5 then
    if ProtoSub == 0 then	--proto DSM2_22 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="CH9", 
source=defaultChannel(8), weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="CH10", 
source=defaultChannel(9), weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="CH11", 
source=defaultChannel(10), weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="CH12", 
source=defaultChannel(11), weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto DSM2_11 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="CH9", 
source=defaultChannel(8), weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="CH10", 
source=defaultChannel(9), weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="CH11", 
source=defaultChannel(10), weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="CH12", 
source=defaultChannel(11), weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto DSMX_22 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="CH9", 
source=defaultChannel(8), weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="CH10", 
source=defaultChannel(9), weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="CH11", 
source=defaultChannel(10), weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="CH12", 
source=defaultChannel(11), weight=100, multiplex=ADD })
    end
    if ProtoSub == 3 then	--proto DSMX_11 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="CH9", 
source=defaultChannel(8), weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="CH10", 
source=defaultChannel(9), weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="CH11", 
source=defaultChannel(10), weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="CH12", 
source=defaultChannel(11), weight=100, multiplex=ADD })
    end
    if ProtoSub == 4 then	--proto AUTO 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="CH9", 
source=defaultChannel(8), weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="CH10", 
source=defaultChannel(9), weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="CH11", 
source=defaultChannel(10), weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="CH12", 
source=defaultChannel(11), weight=100, multiplex=ADD })
    end
  elseif ProtoId == 6 then
    if ProtoSub == 0 then	--proto DEVO 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 7 then
    if ProtoSub == 0 then	--proto YD717 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto SKYWLKR 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto SYMAX4 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 3 then	--proto XINXUN 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 4 then	--proto NIHUI 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 8 then
    if ProtoSub == 0 then	--proto WLTOYS 
      model.insertMix(4, model.getMixesCount(4), { name="DR", source=92,
 weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="THOLD", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="IDLEUP", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="GYRO", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="Ttrim", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="Atrim", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="Etrim", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="", source=92,
 weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto FEILUN 
      model.insertMix(4, model.getMixesCount(4), { name="DR", source=92,
 weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="THOLD", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="IDLEUP", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="GYRO", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="Ttrim", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="Atrim", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="Etrim", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="", source=92,
 weight=100, multiplex=ADD })
    end
  elseif ProtoId == 9 then
    if ProtoSub == 0 then	--proto SYMAX 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="", source=92, 
weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto SYMAX5C 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="", source=92, 
weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 10 then
    if ProtoSub == 0 then	--proto SLT 
      model.insertMix(4, model.getMixesCount(4), { name="GEAR", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="PITCH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 11 then
    if ProtoSub == 0 then	--proto GREEN 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="RATE", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto BLUE 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="RATE", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto DM007 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="MODE", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 3 then	--proto Q282 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="XCAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="YCAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="", source=92,
 weight=100, multiplex=ADD })
    end
    if ProtoSub == 4 then	--proto JC3015_1 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="MODE", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 5 then	--proto JC3015_2 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="MODE", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="DFLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 6 then	--proto MK33041 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="MODE", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="", source=92,
 weight=100, multiplex=ADD })
    end
    if ProtoSub == 7 then	--proto Q242 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="XCAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="YCAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="", source=92,
 weight=100, multiplex=ADD })
    end
  elseif ProtoId == 12 then
    if ProtoSub == 0 then	--proto CG023 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGHT", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto YD829 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="", source=92, 
weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto H8_3D 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LIGTH", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="OPT1", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="OPT2", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="CAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 13 then
    if ProtoSub == 0 then	--proto BAYANG 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="INVERTED", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="", source=92,
 weight=100, multiplex=ADD })
    end
  elseif ProtoId == 14 then
    if ProtoSub == 0 then	--proto CH_16 
      model.insertMix(4, model.getMixesCount(4), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="----", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="----", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="----", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="----", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(13, model.getMixesCount(13), { name="----", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(14, model.getMixesCount(14), { name="----", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(15, model.getMixesCount(15), { name="----", 
source=92, weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto CH_8 
      model.insertMix(4, model.getMixesCount(4), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="---", 
source=92, weight=100, multiplex=ADD })
    end
  elseif ProtoId == 15 then
    if ProtoSub == 0 then	--proto ESKY 
      model.insertMix(4, model.getMixesCount(4), { name="GYRO", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="PITCH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 16 then
    if ProtoSub == 0 then	--proto MT99 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto H7 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto YZ 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 3 then	--proto LS 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="INVERT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 17 then
    if ProtoSub == 0 then	--proto WLH08 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="AUTOFLIP", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="PAN", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="TILT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(13, model.getMixesCount(13), { name="Reset/Bind", 
source=92, weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto X600 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="AUTOFLIP", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="PAN", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="TILT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(13, model.getMixesCount(13), { name="Reset/Bind", 
source=92, weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto X800 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="AUTOFLIP", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="PAN", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="TILT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(13, model.getMixesCount(13), { name="Reset/Bind", 
source=92, weight=100, multiplex=ADD })
    end
    if ProtoSub == 3 then	--proto H26D 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="AUTOFLIP", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="PAN", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="TILT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(13, model.getMixesCount(13), { name="Reset/Bind", 
source=92, weight=100, multiplex=ADD })
    end
    if ProtoSub == 4 then	--proto E010 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="AUTOFLIP", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="PAN", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="TILT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(13, model.getMixesCount(13), { name="Reset/Bind", 
source=92, weight=100, multiplex=ADD })
    end
  elseif ProtoId == 18 then
    if ProtoSub == 0 then	--proto SHENQI 
      model.insertMix(4, model.getMixesCount(4), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 19 then
    if ProtoSub == 0 then	--proto FY326 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="Calibrate", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="Expert", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto FY319 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="Calibrate", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="Expert", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 20 then
    if ProtoSub == 0 then	--proto SFHSS 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 21 then
    if ProtoSub == 0 then	--proto J6PRO 
      model.insertMix(4, model.getMixesCount(4), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="", source=92,
 weight=100, multiplex=ADD })
    end
  elseif ProtoId == 22 then
    if ProtoSub == 0 then	--proto FQ777 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="EXPERT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 23 then
    if ProtoSub == 0 then	--proto ASSAN 
      model.insertMix(4, model.getMixesCount(4), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="", source=92,
 weight=100, multiplex=ADD })
    end
  elseif ProtoId == 24 then
    if ProtoSub == 0 then	--proto FRSKYV 
    end
  elseif ProtoId == 25 then
    if ProtoSub == 0 then	--proto HONTAI 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="CAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="", source=92,
 weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto JJRCX1 
      model.insertMix(4, model.getMixesCount(4), { name="", source=92, 
weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="ARM", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto X5C1 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="PICTURE", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="RTH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="CAL", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="", source=92,
 weight=100, multiplex=ADD })
    end
    if ProtoSub == 3 then	--proto FQ777 
      model.insertMix(4, model.getMixesCount(4), { name="", source=92, 
weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="SNAPSHOT", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="HEADLESS", 
source=91, weight=100, multiplex=ADD })
    end
  elseif ProtoId == 26 then
    if ProtoSub == 0 then	--proto OPENLRS 
    end
  elseif ProtoId == 39 then
    if ProtoSub == 0 then	--proto JOYSWAY 
      model.insertMix(4, model.getMixesCount(4), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 40 then
    if ProtoSub == 0 then	--proto WK2801 
      model.insertMix(4, model.getMixesCount(4), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto WK2601 
      model.insertMix(4, model.getMixesCount(4), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto WK2401 
      model.insertMix(4, model.getMixesCount(4), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 41 then
    if ProtoSub == 0 then	--proto SKYARTEC 
      model.insertMix(4, model.getMixesCount(4), { name=" ? ", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name=" ? ", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name=" ?", source=92,
 weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 43 then
    if ProtoSub == 0 then	--proto U816_V1 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP 360", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="MODE 2", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="", source=92,
 weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto U816_V2 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP 360", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="MODE 2", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="", source=92,
 weight=100, multiplex=ADD })
    end
    if ProtoSub == 2 then	--proto U839_2014 
      model.insertMix(4, model.getMixesCount(4), { name="FLIP 360", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="FLIP", 
source=94, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="VIDEO", 
source=0, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="LED", 
source=96, weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="MODE 2", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="---", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="", source=92,
 weight=100, multiplex=ADD })
    end
  elseif ProtoId == 44 then
    if ProtoSub == 0 then	--proto FBL100 
      model.insertMix(4, model.getMixesCount(4), { name=" ? ", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name=" ? ", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name=" ? ", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name=" ?", source=92,
 weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
    if ProtoSub == 1 then	--proto HP100 
      model.insertMix(4, model.getMixesCount(4), { name=" ? ", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name=" ? ", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name=" ? ", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name=" ?", source=92,
 weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 49 then
    if ProtoSub == 0 then	--proto HM830 
      model.insertMix(4, model.getMixesCount(4), { name="Bouton", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 50 then
    if ProtoSub == 0 then	--proto CFLIE 
      model.insertMix(4, model.getMixesCount(4), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 51 then
    if ProtoSub == 0 then	--proto H377 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 52 then
    if ProtoSub == 0 then	--proto ESKY150 
      model.insertMix(4, model.getMixesCount(4), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 53 then
    if ProtoSub == 0 then	--proto BLUEFLY 
      model.insertMix(4, model.getMixesCount(4), { name="GEAR", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="PITCH", 
source=92, weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 54 then
    if ProtoSub == 0 then	--proto NE260 
      model.insertMix(4, model.getMixesCount(4), { name="", source=92, 
weight=100, multiplex=ADD })
    end
  elseif ProtoId == 55 then
    if ProtoSub == 0 then	--proto AFHDS2A 
      model.insertMix(4, model.getMixesCount(4), { name="CH5", 
source=defaultChannel(4), weight=100, multiplex=ADD })
      model.insertMix(5, model.getMixesCount(5), { name="CH6", 
source=defaultChannel(5), weight=100, multiplex=ADD })
      model.insertMix(6, model.getMixesCount(6), { name="CH7", 
source=defaultChannel(6), weight=100, multiplex=ADD })
      model.insertMix(7, model.getMixesCount(7), { name="CH8", 
source=defaultChannel(7), weight=100, multiplex=ADD })
      model.insertMix(8, model.getMixesCount(8), { name="CH9", 
source=defaultChannel(8), weight=100, multiplex=ADD })
      model.insertMix(9, model.getMixesCount(9), { name="CH10", 
source=defaultChannel(9), weight=100, multiplex=ADD })
      model.insertMix(10, model.getMixesCount(10), { name="CH11", 
source=defaultChannel(10), weight=100, multiplex=ADD })
      model.insertMix(11, model.getMixesCount(11), { name="CH12", 
source=defaultChannel(11), weight=100, multiplex=ADD })
      model.insertMix(12, model.getMixesCount(12), { name="CH13", 
source=defaultChannel(12), weight=100, multiplex=ADD })
      model.insertMix(13, model.getMixesCount(13), { name="CH14", 
source=defaultChannel(13), weight=100, multiplex=ADD })
      model.insertMix(14, model.getMixesCount(14), { name="Failsave T", 
source=92, weight=100, multiplex=ADD })
    end
  elseif ProtoId == 56 then
    if ProtoSub == 0 then	--proto INAV 
    end
  end

end

local function confirmationMenu(event)
  if dirty then
    dirty = false
    drawConfirmationMenu()
  end

navigate(event, fieldsMax, PROTO_PAGE, page)

if event == EVT_EXIT_BREAK then
    return 2
  elseif event == EVT_ENTER_LONG then
    killEvents(event)
    applySettings()
    return 2
  else
    return 0
  end
end

-- Main
local function run(event)
  if event == nil then
    error("Cannot be run as a model script!")
  end
  lcd.lock()
  if page == PROTO_PAGE then
    engineMenu(event)
  elseif page == CONFIRMATION_PAGE then
    return confirmationMenu(event)
  end
  return 0
end

return { init=init, run=run }

Liste Protocoles Close

0.0 SERIAL         16.0 ESKY          
1.0 FLYSKY         17.0 MT99          
1.1 V9X9           17.1 H7            
1.2 V6X6           17.2 YZ            
1.3 V912           17.3 LS            
2.0 H107           18.0 WLH08         
2.1 H301           18.1 X600          
2.2 H501           18.2 X800          
3.0 FRSKYD         18.3 H26D          
4.0 HISKY          18.4 E010          
4.1 HK310          19.0 SHENQI        
5.0 V2X2           20.0 FY326         
6.0 DSM2_22        20.1 FY319         
6.1 DSM2_11        21.0 SFHSS         
6.2 DSMX_22        22.0 J6PRO         
6.3 DSMX_11        23.0 FQ777         
6.4 AUTO           24.0 ASSAN         
7.0 DEVO           25.0 FRSKYV        
8.0 YD717          26.0 HONTAI        
8.1 SKYWLKR        26.1 JJRCX1        
8.2 SYMAX4         26.2 X5C1          
8.3 XINXUN         26.3 FQ777         
8.4 NIHUI          27.0 OPENLRS       
9.0 WLTOYS         40.0 JOYSWAY       
9.1 FEILUN         41.0 WK2801        
10.0 SYMAX         41.1 WK2601        
10.1 SYMAX5C       41.2 WK2401        
11.0 SLT           42.0 SKYARTEC      
12.0 GREEN         44.0 U816_V1       
12.1 BLUE          44.1 U816_V2       
12.2 DM007         44.2 U839_2014     
12.3 Q282          45.0 FBL100        
12.4 JC3015_1      45.1 HP100         
12.5 JC3015_2      50.0 HM830         
12.6 MK33041       51.0 CFLIE         
12.7 Q242          52.0 H377          
13.0 CG023         53.0 ESKY150       
13.1 YD829         54.0 BLUEFLY       
13.2 H8_3D         55.0 NE260         
14.0 BAYANG        56.0 AFHDS2A       
15.0 CH_16         57.0 INAV          
15.1 CH_8