XK2 Gyro off

Missing low batt telem

Lua_scripts/MultiChan.txt

@@ -91,6 +91,7 @@
 58,1,FX,620,1
 58,2,FX,9630,1,Rate,Gyro,TrimR,TrimA,TrimE
 58,3,FX,Q560,1,FLIP,Gyro,LEDs
+58,4,FX,QF012,1,FLIP,Gyro,Invert,Reset
 20,0,FY326,FY326,1,Flip,RTH,HLess,Expert,Calib
 20,1,FY326,FY319,1,Flip,RTH,HLess,Expert,Calib
 23,0,FY326,FY326,1,Flip,RTH,HLess,Expert
@@ -138,9 +139,9 @@
 17,2,MT99XX,YZ,1,Flip,LED,Pict,Video,HLess
 17,3,MT99XX,LS,1,Flip,Invert,Pict,Video,HLess
 17,4,MT99XX,FY805,1,Flip,n-a,n-a,n-a,HLess
-17,5,MT99XX,A180,0,3D_6G
+17,5,MT99XX,A180,0,3D_6G,Rate,3D_6G
 17,6,MT99XX,Dragon,0,Mode,RTH
-17,7,MT99XX,F949G,0,6G_3D,Light
+17,7,MT99XX,F949G,0,6G_3D,Light,Rates,Unk1,Unk2
 44,0,NCC1701,Std,1,Warp
 77,0,OMP,M2,0,THold,IdleUp,6G_3D
 60,0,Pelikan,PRO_V4,0,CH5,CH6,CH7,CH8
@@ -229,5 +230,8 @@
 98,0,Kyosho3,ASF,0
 100,0,YuXiang,Std,0,Lock,Rate,Land,Manual,Flip,Mode,Pitch
 102,0,JIABAILE,Std,0,Speed,Light,Flash
-102,1,JIABAILE,Gyro,0,Speed,Light,Flash,Tr_ST
+102,1,JIABAILE,Gyro,0,Speed,Light,Flash,ST_Tr
 103,0,H36,Std,1,Flip,HLess,RTH
+104,0,KAMTOM,Std,0,ST_Tr,TH_Tr,TH_DR
+105,0,Shenqi2,Std,1
+106,0,WL91x,Std,0

Multiprotocol/DSM_cyrf6936.ino

@@ -462,7 +462,7 @@ uint16_t DSM_callback()
 						else
 							return DSM2_SFC_PERIOD - DSM_CH1_CH2_DELAY - DSM_WRITE_DELAY - DSM_READ_DELAY;
 					}
-					return 11000 - DSM_WRITE_DELAY - DSM_READ_DELAY;
+					return 10900 - DSM_WRITE_DELAY - DSM_READ_DELAY;	//Was 11000 but the SR6200A needs 10900 to report telemetry correctly
 				}
 			#endif
 			return 11000 - DSM_CH1_CH2_DELAY - DSM_WRITE_DELAY - DSM_READ_DELAY;
@@ -470,12 +470,15 @@ uint16_t DSM_callback()
 		case DSM_CH2_READ_B:
 			//Read telemetry
 			rx_phase = CYRF_ReadRegister(CYRF_07_RX_IRQ_STATUS);
+			debug("ST1:%02X ",rx_phase);
 			if((rx_phase & 0x03) == 0x02)  					// RXC=1, RXE=0 then 2nd check is required (debouncing)
 				rx_phase |= CYRF_ReadRegister(CYRF_07_RX_IRQ_STATUS);
+			debug("ST2:%02X ",rx_phase);
 			if((rx_phase & 0x07) == 0x02)
 			{ // good data (complete with no errors)
 				CYRF_WriteRegister(CYRF_07_RX_IRQ_STATUS, 0x80);	// need to set RXOW before data read
 				length=CYRF_ReadRegister(CYRF_09_RX_COUNT);
+				debug("RX(%d)",length);
 				if(length>TELEMETRY_BUFFER_SIZE-2)
 					length=TELEMETRY_BUFFER_SIZE-2;
 				CYRF_ReadDataPacketLen(packet_in+1, length);
@@ -489,8 +492,11 @@ uint16_t DSM_callback()
 					}
 				#endif
 				packet_in[0]=CYRF_ReadRegister(CYRF_13_RSSI)&0x1F;// store RSSI of the received telemetry signal
+				//for(uint8_t i=0;i<length+1;i++)
+				//	debug(" %02X", packet_in[i]);
 				telemetry_link=1;
 			}
+			debugln("");
 			CYRF_WriteRegister(CYRF_29_RX_ABORT, 0x20);		// Abort RX operation
 			if (phase == DSM_CH2_READ_A && (sub_protocol==DSM2_1F || sub_protocol==DSMX_1F) && num_ch < 8)	// 22ms mode
 			{

Multiprotocol/FX_nrf24l01.ino

@@ -62,7 +62,7 @@ static void __attribute__((unused)) FX_send_packet()
 					trim_ch++;
 					if(trim_ch > 3) trim_ch = 0;
 				}
-				else // FX_Q560
+				else // FX_Q560, QF012
 					trim_ch = 0;
 			}
 		}
@@ -85,12 +85,16 @@ static void __attribute__((unused)) FX_send_packet()
 		val = trim_ch==0 ? 0x20 : (convert_channel_8b(trim_ch + CH6) >> 2);	// no trim on Throttle
 		packet[4] = val;			// Trim for channel x 0C..20..34
 		packet[5] = (trim_ch << 4)	// channel x << 4
-					| GET_FLAG(CH5_SW, 0x01)  // DR toggle swich: 0 small throw, 1 large throw / Q560 acrobatic
+					| GET_FLAG(CH5_SW, (sub_protocol == FX_QF012 ? 0x08 : 0x01))  // DR toggle swich: 0 small throw, 1 large throw / Q560 acrobatic / QF012 Special effects
 					// FX9630  =>0:6G small throw, 1:6G large throw, 2:3D
 					// QIDI-550=>0:3D, 1:6G, 2:Torque
+					// QF012=>0:beginner(6G), 1:mid(3D), 2:expert(Gyro off) 
 					| (Channel_data[CH6] < CHANNEL_MIN_COMMAND ? 0x00 : (Channel_data[CH6] > CHANNEL_MAX_COMMAND ? 0x04 : 0x02));
 		if(sub_protocol == FX_Q560)
 			packet[5] |= GET_FLAG(CH7_SW, 0x18);	// Q560 LED flag 0x10 conflicting with trim_ch... Corrected on new boards using 0x08 instead
+		else if (sub_protocol == FX_QF012) 
+      			packet[5] |=  GET_FLAG(CH7_SW, 0x40)  // QF012 invert flight
+                		    | GET_FLAG(CH8_SW, 0x80);  // QF012 Restore fine tunning midpoint
 	}
 	else // FX816 and FX620
 	{

Multiprotocol/Kamtom_nrf24l01.ino

@@ -0,0 +1,185 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#if defined(KAMTOM_NRF24L01_INO)
+
+#include "iface_xn297.h"
+
+//#define FORCE_KAMTOM_ORIGINAL_ID
+
+#define KAMTOM_PAYLOAD_SIZE			16
+#define KAMTOM_RF_NUM_CHANNELS		4
+#define KAMTOM_BIND_COUNT			2000
+#define KAMTOM_WRITE_TIME			650
+#define KAMTOM_BIND_CHANNEL			0x28	//40
+#define KAMTOM_PACKET_PERIOD		3585
+
+
+enum {
+	KAMTOM_DATA,
+	KAMTOM_RX,
+};
+
+static void __attribute__((unused)) KAMTOM_send_packet()
+{
+	if(bind_counter)
+	{
+		bind_counter--;
+		if(!bind_counter)
+			BIND_DONE;
+	}
+
+	memset(packet, 0x00, 16);
+
+	if(IS_BIND_DONE)
+	{//Normal
+		XN297_Hopping(hopping_frequency_no);
+		hopping_frequency_no++;
+		hopping_frequency_no &= 3;
+
+		//RXID
+		packet[0] = rx_tx_addr[0];
+		packet[2] = rx_tx_addr[1];
+		//Next RF channel
+		packet[1] = hopping_frequency[hopping_frequency_no];
+		//Channels and trims
+		for(uint8_t i=0; i<6; i++)
+		{
+			packet[4+i] = convert_channel_s8b(CH_TAER[i]);
+			if(i>3) //ST_TR and TH_TR
+				packet[4+i] >>= 2;
+		}
+		//packet[11] = 0x00;	//??
+		//TH_DR
+		packet[12] = convert_channel_16b_limit(CH7,0x25,0x64);
+	}
+	else
+	{
+		packet[1] = KAMTOM_BIND_CHANNEL;
+		memcpy(&packet[4],hopping_frequency,4);
+		packet[12] = 0xA5;
+	}
+	packet[10] = 0x40;	//??
+	//Checksum
+	uint16_t sum = packet[1];
+	for(uint8_t i=4;i<13;i++)
+		 sum += packet[i];
+	packet[13] = sum;
+	packet[3] = (sum>>6) & 0xFC;
+	//TXID
+	packet[14] = rx_tx_addr[2];
+	packet[15] = rx_tx_addr[3];
+	// Send
+	XN297_SetPower();
+	XN297_SetTxRxMode(TX_EN);
+	XN297_WriteEnhancedPayload(packet, KAMTOM_PAYLOAD_SIZE,false);
+	#if 0
+	//def DEBUG_SERIAL
+		for(uint8_t i=0; i < KAMTOM_PAYLOAD_SIZE; i++)
+			debug("%02X ", packet[i]);
+		debugln();
+	#endif
+}
+
+static void __attribute__((unused)) KAMTOM_initialize_txid()
+{
+	calc_fh_channels(4);
+	#ifdef FORCE_KAMTOM_ORIGINAL_ID
+		rx_tx_addr[0] = 0xC7;
+		rx_tx_addr[1] = 0x78;
+		rx_tx_addr[2] = 0x2C;
+		rx_tx_addr[3] = 0x25;
+		hopping_frequency[0] = 59;
+		hopping_frequency[1] = 59;
+		hopping_frequency[2] = 71;
+		hopping_frequency[3] = 65;
+	#endif
+}
+
+static void __attribute__((unused)) KAMTOM_RF_init()
+{
+	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_1M);
+	//Address
+	XN297_SetTXAddr((uint8_t*)"\xCC\xDD\xEE\xDD", 4);
+	XN297_SetRXAddr((uint8_t*)"\xCC\xDD\xEE\xDD", KAMTOM_PAYLOAD_SIZE);
+	XN297_RFChannel(KAMTOM_BIND_CHANNEL);
+}
+
+uint16_t KAMTOM_callback()
+{
+	static bool rx=false;
+	
+	switch(phase)
+	{
+		case KAMTOM_DATA:
+			rx = XN297_IsRX();
+			XN297_SetTxRxMode(TXRX_OFF);
+			#ifdef MULTI_SYNC
+				telemetry_set_input_sync(KAMTOM_PACKET_PERIOD);
+			#endif
+			KAMTOM_send_packet();
+			if(rx)
+			{
+				uint8_t val=XN297_ReadEnhancedPayload(packet_in, KAMTOM_PAYLOAD_SIZE);
+				if(val==KAMTOM_PAYLOAD_SIZE)
+				{
+					BIND_DONE;
+					if(packet_in[0] == 0xA0 && packet_in[14] == rx_tx_addr[2] && packet_in[15] == rx_tx_addr[3])
+					{//Good packet with our TXID
+						rx_tx_addr[0] = packet_in[9];
+						rx_tx_addr[1] = packet_in[10];
+						#ifdef KAMTOM_HUB_TELEMETRY
+							v_lipo1 = packet_in[1] == 0x03 ? 0x00:0xFF;		// low voltage
+							telemetry_link = 1;
+						#endif
+					}
+					#if 0
+						for(uint8_t i=0; i < KAMTOM_PAYLOAD_SIZE; i++)
+							debug(" %02X", packet_in[i]);
+						debugln();
+					#endif
+				}
+			}
+			phase++;
+			return KAMTOM_WRITE_TIME;
+		default: //KAMTOM_RX
+			//{ // Wait for packet to be sent before switching to receive mode
+			//	uint16_t start=(uint16_t)micros();
+			//	while ((uint16_t)((uint16_t)micros()-(uint16_t)start) < 500)
+			//		if(XN297_IsPacketSent())
+			//			break;
+			//}
+			//Switch to RX
+			XN297_SetTxRxMode(TXRX_OFF);
+			XN297_SetTxRxMode(RX_EN);
+			phase = KAMTOM_DATA;
+			return KAMTOM_PACKET_PERIOD - KAMTOM_WRITE_TIME;
+	}
+	return 0;
+}
+
+void KAMTOM_init()
+{
+	KAMTOM_initialize_txid();
+	KAMTOM_RF_init();
+
+	bind_counter = KAMTOM_BIND_COUNT;
+	phase = KAMTOM_DATA;
+	hopping_frequency_no = 0;
+	#ifdef KAMTOM_HUB_TELEMETRY
+		RX_RSSI = 100;		// Dummy value
+	#endif
+}
+
+#endif

Multiprotocol/Kyosho3_cyrf6936.ino

@@ -112,7 +112,10 @@ void KYOSHO3_init()
 		debugln("RF CH: %02X",hopping_frequency[0]);
 	#endif
 
-	CYRF_ConfigRFChannel(hopping_frequency[0]);
+	if(IS_BIND_IN_PROGRESS)
+		CYRF_ConfigRFChannel(0x04);
+	else
+		CYRF_ConfigRFChannel(hopping_frequency[0]);
 	
 	bind_counter = 8217;
 	phase = 0;

Multiprotocol/Multi.txt

@@ -55,7 +55,7 @@
 55,Frsky_RX,Multi,CloneTX,EraseTX,CPPM
 56,AFHDS2A_RX,Multi,CPPM
 57,HoTT,Sync,No_Sync
-58,FX,816,620,9630,Q560
+58,FX,816,620,9630,Q560,QF012
 59,Bayang_RX,Multi,CPPM
 60,Pelikan,Pro,Lite,SCX24
 61,EazyRC
@@ -99,3 +99,6 @@
 100,YuXiang
 102,JIABAILE,STD,GYRO
 103,H36
+104,KAMTOM
+105,Shenqi2
+106,WL91x

Multiprotocol/Multi_Protos.ino

@@ -36,6 +36,7 @@ const char STR_MT99XX[]		="MT99XX";
 const char STR_MT99XX2[]	="MT99XX2";
 const char STR_MJXQ[]		="MJXq";
 const char STR_SHENQI[]		="Shenqi";
+const char STR_SHENQI2[]	="Shenqi2";
 const char STR_FY326[]		="FY326";
 const char STR_FUTABA[]		="Futaba";
 const char STR_J6PRO[]		="J6 Pro";
@@ -113,8 +114,10 @@ const char STR_SGF22[]      ="SGF22";
 const char STR_EAZYRC[]     ="EazyRC";
 const char STR_KYOSHO3[]    ="Kyosho3";
 const char STR_YUXIANG[]    ="YuXiang";
-const char STR_PINECONE[]   ="PineCone";
+const char STR_UDIRC[]      ="UDIRC";
-const char STR_JIABAILE[]	="JIABAILE";
+const char STR_JIABAILE[]   ="JIABAILE";
+const char STR_KAMTOM[]     ="KAMTOM";
+const char STR_WL91X[]      ="WL91x";
 
 const char STR_SUBTYPE_FLYSKY[] =     "\x04""Std\0""V9x9""V6x6""V912""CX20";
 const char STR_SUBTYPE_HUBSAN[] =     "\x04""H107""H301""H501";
@@ -184,7 +187,7 @@ const char STR_SUBTYPE_JJRC345[] =    "\x08""JJRC345\0""SkyTmblr";
 const char STR_SUBTYPE_MOULDKG[] =    "\x06""Analog""Digit\0";
 const char STR_SUBTYPE_KF606[] =      "\x06""KF606\0""MIG320""ZCZ50\0";
 const char STR_SUBTYPE_E129[] =       "\x04""E129""C186";
-const char STR_SUBTYPE_FX[] =         "\x04""816\0""620\0""9630""Q560";
+const char STR_SUBTYPE_FX[] =         "\x05""816\0 ""620\0 ""9630\0""Q560\0""QF012";
 const char STR_SUBTYPE_SGF22[] =      "\x04""F22\0""F22S""J20\0";
 const char STR_SUBTYPE_JIABAILE[] =   "\x04""Std\0""Gyro";
 #define NO_SUBTYPE		nullptr
@@ -341,7 +344,7 @@ const mm_protocol_definition multi_protocols[] = {
 		{PROTO_FUTABA,     STR_FUTABA,    STR_SUBTYPE_FUTABA,    1, OPTION_RFTUNE,  1, 1, SW_CC2500, SFHSS_init,      SFHSS_callback      },
 	#endif
 	#if defined(FX_NRF24L01_INO)
-		{PROTO_FX,         STR_FX,        STR_SUBTYPE_FX,        4, OPTION_NONE,    0, 0, SW_NRF,    FX_init,         FX_callback         },
+		{PROTO_FX,         STR_FX,        STR_SUBTYPE_FX,        5, OPTION_NONE,    0, 0, SW_NRF,    FX_init,         FX_callback         },
 	#endif
 	#if defined(FY326_NRF24L01_INO)
 		{PROTO_FY326,      STR_FY326,     STR_SUBTYPE_FY326,     2, OPTION_NONE,    0, 0, SW_NRF,    FY326_init,      FY326_callback      },
@@ -391,6 +394,9 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(JOYSWAY_A7105_INO)
 		{PROTO_JOYSWAY,    STR_JOYSWAY,   NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_A7105,  JOYSWAY_init,    JOYSWAY_callback    },
 	#endif
+	#if defined(KAMTOM_NRF24L01_INO)
+		{PROTO_KAMTOM,     STR_KAMTOM,    NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    KAMTOM_init,     KAMTOM_callback     },
+	#endif
 	#if defined(KF606_CCNRF_INO)
 		{PROTO_KF606,      STR_KF606,     STR_SUBTYPE_KF606,     3, OPTION_RFTUNE,  0, 0, SW_NRF,    KF606_init,      KF606_callback      },
 	#endif
@@ -436,9 +442,6 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(PELIKAN_A7105_INO)
 		{PROTO_PELIKAN,    STR_PELIKAN,   STR_SUBTYPE_PELIKAN,   3, OPTION_NONE,    0, 1, SW_A7105,  PELIKAN_init,    PELIKAN_callback    },
 	#endif
-	#if defined(PINECONE_CCNRF_INO)
-		{PROTO_PINECONE,   STR_PINECONE,  NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    PINECONE_init,   PINECONE_callback   },
-	#endif
 	#if defined(POTENSIC_NRF24L01_INO)
 		{PROTO_POTENSIC,   STR_POTENSIC,  STR_SUBTYPE_POTENSIC,  1, OPTION_NONE,    0, 0, SW_NRF,    POTENSIC_init,   POTENSIC_callback   },
 	#endif
@@ -475,6 +478,9 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(SHENQI_NRF24L01_INO)
 		{PROTO_SHENQI,     STR_SHENQI,    NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    SHENQI_init,     SHENQI_callback     },
 	#endif
+	#if defined(SHENQI2_NRF24L01_INO)
+		{PROTO_SHENQI2,    STR_SHENQI2,   NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    SHENQI2_init,     SHENQI2_callback   },
+	#endif
 	#if defined(SKYARTEC_CC2500_INO)
 		{PROTO_SKYARTEC,   STR_SKYARTEC,  NO_SUBTYPE,            0, OPTION_RFTUNE,  0, 1, SW_CC2500, SKYARTEC_init,   SKYARTEC_callback   },
 	#endif
@@ -487,6 +493,9 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(TRAXXAS_CYRF6936_INO)
 		{PROTO_TRAXXAS,    STR_TRAXXAS,   STR_SUBTYPE_TRAXXAS,   2, OPTION_NONE,    0, 0, SW_CYRF,   TRAXXAS_init,    TRAXXAS_callback    },
 	#endif
+	#if defined(UDIRC_CCNRF_INO)
+		{PROTO_UDIRC,      STR_UDIRC,     NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    UDIRC_init,      UDIRC_callback      },
+	#endif
 	#if defined(V2X2_NRF24L01_INO)
 		{PROTO_V2X2,       STR_V2X2,      STR_SUBTYPE_V2X2,      3, OPTION_NONE,    0, 0, SW_NRF,    V2X2_init,       V2X2_callback       },
 	#endif
@@ -496,9 +505,6 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(V911S_CCNRF_INO)
 		{PROTO_V911S,      STR_V911S,     STR_SUBTYPE_V911S,     2, OPTION_RFTUNE,  0, 0, SW_NRF,    V911S_init,      V911S_callback      },
 	#endif
-	#if defined(WK2x01_CYRF6936_INO)
-		{PROTO_WK2x01,     STR_WK2x01,    STR_SUBTYPE_WK2x01,    6, OPTION_NONE,    1, 1, SW_CYRF,   WK_init,         WK_callback         },
-	#endif
 	#if defined(WFLY_CYRF6936_INO)
 		{PROTO_WFLY,       STR_WFLY,      STR_SUBTYPE_WFLY,      1, OPTION_NONE,    1, 0, SW_CYRF,   WFLY_init,       WFLY_callback       },
 	#endif
@@ -506,6 +512,13 @@ const mm_protocol_definition multi_protocols[] = {
 		{PROTO_WFLY2,      STR_WFLY2,     STR_SUBTYPE_WFLY2,     1, OPTION_OPTION,  1, 0, SW_A7105,  WFLY2_init,      WFLY2_callback      },
 //		{PROTO_WFLY2,      STR_WFLY2,     STR_SUBTYPE_WFLY2,     1, OPTION_WBUS,    1, 0, SW_A7105,  WFLY2_init,      WFLY2_callback      },// crash OpenTX...
 	#endif
+	#if defined(WK2x01_CYRF6936_INO)
+		{PROTO_WK2x01,     STR_WK2x01,    STR_SUBTYPE_WK2x01,    6, OPTION_NONE,    1, 1, SW_CYRF,   WK_init,         WK_callback         },
+	#endif
+	#if defined(WL91X_CCNRF_INO)
+		{PROTO_WL91X,      STR_WL91X,     NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    WL91X_init,      WL91X_callback      },
+	#endif
+	
 	#if defined(XERALL_NRF24L01_INO)
 		{PROTO_XERALL,     STR_XERALL,    NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    XERALL_init,     XERALL_callback     },	
 	#endif

Multiprotocol/Multiprotocol.h

@@ -19,7 +19,7 @@
 #define VERSION_MAJOR		1
 #define VERSION_MINOR		3
 #define VERSION_REVISION	4
-#define VERSION_PATCH_LEVEL	31
+#define VERSION_PATCH_LEVEL	44
 
 #define MODE_SERIAL 0
 
@@ -128,9 +128,12 @@ enum PROTOCOLS
 	PROTO_KYOSHO3	= 98,	// =>CYRF6936
 	PROTO_XK2		= 99,	// =>CC2500 & NRF24L01
 	PROTO_YUXIANG	= 100,	// =>NRF24L01
-	PROTO_PINECONE	= 101,	// =>CC2500 & NRF24L01
+	PROTO_UDIRC		= 101,	// =>CC2500 & NRF24L01
 	PROTO_JIABAILE	= 102,	// =>NRF24L01
 	PROTO_H36		= 103,	// =>NRF24L01
+	PROTO_KAMTOM	= 104,	// =>NRF24L01
+	PROTO_SHENQI2	= 105,	// =>NRF24L01
+	PROTO_WL91X		= 106,	// =>CC2500 & NRF24L01
 	
 	PROTO_NANORF	= 126,	// =>NRF24L01
 	PROTO_TEST		= 127,	// =>CC2500
@@ -488,6 +491,7 @@ enum FX
 	FX620			= 1,
     FX9630          = 2,
 	FX_Q560			= 3,
+	FX_QF012  = 4,
 };
 enum SGF22
 {

Multiprotocol/Pinecone_ccnrf.ino

@@ -1,167 +0,0 @@
-/*
- This project is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
-
-Multiprotocol is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- GNU General Public License for more details.
-
- You should have received a copy of the GNU General Public License
- along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
- */
-#if defined(PINECONE_CCNRF_INO)
-
-#include "iface_xn297.h"
-
-#define FORCE_PINECONE_ORIGINAL_ID
-
-#define PINECONE_PAYLOAD_SIZE			15
-#define PINECONE_RF_NUM_CHANNELS		4
-#define PINECONE_PACKET_PERIOD			9000
-#define PINECONE_BIND_COUNT				2000
-#define PINECONE_WRITE_TIME				1500
-
-enum {
-	PINECONE_DATA=0,
-	PINECONE_RX,
-};
-
-static void __attribute__((unused)) PINECONE_send_packet()
-{
-	if(rf_ch_num==0)
-	{
-		XN297_Hopping(hopping_frequency_no);
-		debug("H %d ",hopping_frequency_no);
-		hopping_frequency_no++;
-		hopping_frequency_no &= 3;
-	}
-
-	if(bind_counter==0) bind_counter=2;
-	memset(&packet[3], 0x00, 12);
-	if(bind_counter)
-	{//Bind in progress
-		bind_counter--;
-		if(bind_counter)
-		{//Bind
-			packet[0] = 0x01;
-			memcpy(&packet[1],rx_tx_addr,5);
-		}
-		else
-		{//Switch to normal
-			XN297_SetTXAddr(rx_tx_addr, 5);
-			XN297_SetRXAddr(rx_tx_addr, PINECONE_PAYLOAD_SIZE);
-		}
-	}
-	if(!bind_counter)
-	{//Normal
-		packet[0] = 0x08;
-		packet[1] = convert_channel_16b_limit(AILERON,0,200);	//ST
-		packet[2] = convert_channel_16b_limit(THROTTLE,0,200);	//TH
-		packet[3] = convert_channel_16b_limit(ELEVATOR,0,200);	//CH4
-		packet[4] = convert_channel_16b_limit(RUDDER,0,200);	//CH3
-	}
-	//packet[5/6..8] = 00 unknown
-	packet[9] = convert_channel_16b_limit(CH5,0,200);			//ESP
-	packet[10] = convert_channel_16b_limit(CH6,0,200);			//ST_TRIM
-	packet[11] = convert_channel_16b_limit(CH7,0,200);			//ST_DR
-	packet[12] = GET_FLAG(CH8_SW,  0x40)						//TH.REV
-				|GET_FLAG(CH9_SW,  0x80);						//ST.REV
-	//packet[13] = 00 unknown
-	for(uint8_t i=0;i<PINECONE_PAYLOAD_SIZE-1;i++)
-		packet[14] += packet[i];
-	// Send
-	XN297_SetPower();
-	XN297_SetTxRxMode(TX_EN);
-	XN297_WriteEnhancedPayload(packet, PINECONE_PAYLOAD_SIZE,false);
-	#ifdef DEBUG_SERIAL
-		for(uint8_t i=0; i < PINECONE_PAYLOAD_SIZE; i++)
-			debug("%02X ", packet[i]);
-		debugln();
-	#endif
-}
-
-static void __attribute__((unused)) PINECONE_initialize_txid()
-{
-	#ifdef FORCE_PINECONE_ORIGINAL_ID
-		rx_tx_addr[0] = 0xD0;
-		rx_tx_addr[1] = 0x06;
-		rx_tx_addr[2] = 0x00;
-		rx_tx_addr[3] = 0x00;
-		rx_tx_addr[4] = 0x81;
-		hopping_frequency[0] = 45;
-		hopping_frequency[1] = 59;
-		hopping_frequency[2] = 52;
-		hopping_frequency[3] = 67;
-	#endif
-}
-
-static void __attribute__((unused)) PINECONE_RF_init()
-{
-	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_250K);
-	//Bind address
-	XN297_SetTXAddr((uint8_t*)"\x01\x03\x05\x07\x09", 5);
-	XN297_SetRXAddr((uint8_t*)"\x01\x03\x05\x07\x09", PINECONE_PAYLOAD_SIZE);
-	XN297_HoppingCalib(PINECONE_RF_NUM_CHANNELS);
-}
-
-uint16_t PINECONE_callback()
-{
-	bool rx;
-	switch(phase)
-	{
-		case PINECONE_DATA:
-			rx = XN297_IsRX();
-			XN297_SetTxRxMode(TXRX_OFF);
-			#ifdef MULTI_SYNC
-				telemetry_set_input_sync(PINECONE_PACKET_PERIOD);
-			#endif
-			PINECONE_send_packet();
-			if(rx)
-			{
-				uint8_t val=XN297_ReadEnhancedPayload(packet_in, PINECONE_PAYLOAD_SIZE);
-				debug("RX %d ",val);
-				if(val==0)
-					rf_ch_num = 1;
-				else
-				{
-					#ifdef DEBUG_SERIAL
-						for(uint8_t i=0; i < PINECONE_PAYLOAD_SIZE; i++)
-							debug("%02X ", packet_in[i]);
-						debugln();
-					#endif
-					//could check the validity of the packet by looking at the sum...
-				}
-				//else
-				//	debug("NOK");
-				debugln("");
-			}
-			phase++;
-			return PINECONE_WRITE_TIME;
-		default: //PINECONE_RX
-			//Wait for the packet transmission to finish
-			while(XN297_IsPacketSent()==false);
-			//Switch to RX
-			XN297_SetTxRxMode(TXRX_OFF);
-			XN297_SetTxRxMode(RX_EN);
-			phase = PINECONE_DATA;
-			return PINECONE_PACKET_PERIOD - PINECONE_WRITE_TIME;
-	}
-	return 0;
-}
-
-void PINECONE_init()
-{
-	PINECONE_initialize_txid();
-	PINECONE_RF_init();
-
-	bind_counter = IS_BIND_IN_PROGRESS ? PINECONE_BIND_COUNT : 1;
-	phase = PINECONE_DATA;
-	hopping_frequency_no = 0;
-	rf_ch_num=0;
-	bind_counter = 2000;
-}
-
-#endif

Multiprotocol/SGF22_nrf24l01.ino

@@ -169,7 +169,7 @@ uint16_t SGF22_callback()
 	}
 	else
 	{//send 3 times in total the same packet
-		NRF24L01_Strobe(REUSE_TX_PL);
+		XN297_ReSendPayload();
 		phase++;
 		if(phase > 2)
 		{

Multiprotocol/SHENQI2_nrf24l01.ino

@@ -0,0 +1,232 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#if defined(SHENQI2_NRF24L01_INO)
+
+#include "iface_xn297.h"
+
+//#define FORCE_SHENQI2_ORIGINAL_ID
+
+#define SHENQI2_PAYLOAD_SIZE		8
+#define SHENQI2_RF_NUM_CHANNELS		16
+#define SHENQI2_BIND_COUNT			2000
+#define SHENQI2_WRITE_TIME			650
+#define SHENQI2_BIND_CHANNEL		44
+#define SHENQI2_PACKET_PERIOD		8210
+
+
+enum {
+	SHENQI2_BIND = 0,
+	SHENQI2_BIND_RX,
+	SHENQI2_DATA,
+};
+
+static void __attribute__((unused)) SHENQI2_send_packet()
+{
+	if(bind_counter)
+	{
+		bind_counter--;
+		if(!bind_counter)
+			BIND_DONE;
+	}
+
+	memset(packet, 0x00, SHENQI2_PAYLOAD_SIZE);
+
+	packet_count &= 0x0F;
+	packet[0] = packet_count;
+	
+	memcpy(&packet[1],rx_tx_addr,5);
+
+	if(IS_BIND_DONE)
+	{//Normal
+		uint8_t val = convert_channel_8b(CH2);
+		if(val < 0x70)
+			val = 0x30;
+		else if(val < 0x80)
+			val = 0x00;
+		else
+		{
+			val &= 0x7F;
+			val >>= 2;
+		}
+		if(Channel_data[CH1] > 1024+50)
+			val |= 0x40;
+		else if(Channel_data[CH1] < 1024-50)
+			val |= 0x80;
+		packet[6] = val;
+		//packet[7] = 0x00;		// ??
+	}
+	else
+		packet[0] |= 0x30;
+
+	// Send
+	XN297_SetPower();
+	XN297_SetTxRxMode(TX_EN);
+	XN297_WriteEnhancedPayload(packet, SHENQI2_PAYLOAD_SIZE, false);
+	#ifdef DEBUG_SERIAL
+		for(uint8_t i=0; i < SHENQI2_PAYLOAD_SIZE; i++)
+			debug("%02X ", packet[i]);
+		debugln();
+	#endif
+}
+
+static void __attribute__((unused)) SHENQI2_initialize_txid()
+{
+	#ifdef FORCE_SHENQI2_ORIGINAL_ID
+		//TXID
+		rx_tx_addr[0] = 0x51;
+		rx_tx_addr[1] = 0x70;
+		rx_tx_addr[2] = 0x02;
+		//RXID
+		rx_tx_addr[3] = 0x46;
+		rx_tx_addr[4] = 0xBE;
+	#endif
+	rx_tx_addr[3] = 0x00;
+	rx_tx_addr[4] = 0x00;
+	//Freq
+	memcpy(hopping_frequency,(uint8_t*)"\x05\x09\x0E\x0F\x17\x1C\x21\x27\x2A\x2C\x33\x39\x3D\x42\x48\x4C",16);
+}
+
+static void __attribute__((unused)) SHENQI2_RF_init()
+{
+	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_1M);
+	//Address
+	XN297_SetTXAddr((uint8_t*)"\x74\xD1\x3A\xF5\x6C", 5);
+	XN297_SetRXAddr((uint8_t*)"\x74\xD1\x3A\xF5\x6C", SHENQI2_PAYLOAD_SIZE);
+	XN297_RFChannel(SHENQI2_BIND_CHANNEL);
+}
+
+uint16_t SHENQI2_callback()
+{
+	static bool rx=false;
+	
+	switch(phase)
+	{
+		case SHENQI2_BIND:
+			rx = XN297_IsRX();
+			XN297_SetTxRxMode(TXRX_OFF);
+			SHENQI2_send_packet();
+			packet_count++;
+			if(rx)
+			{
+				uint8_t val=XN297_ReadEnhancedPayload(packet_in, SHENQI2_PAYLOAD_SIZE);
+				if(val == SHENQI2_PAYLOAD_SIZE)
+				{
+					if(memcmp(rx_tx_addr, packet_in, 3) == 0)
+					{//Good packet with our TXID
+						BIND_DONE;
+						rx_tx_addr[3] = packet_in[3];
+						rx_tx_addr[4] = packet_in[4];
+						packet_count = 0;
+						phase = SHENQI2_DATA;
+					}
+					#ifdef DEBUG_SERIAL
+						for(uint8_t i=0; i < SHENQI2_PAYLOAD_SIZE; i++)
+							debug(" %02X", packet_in[i]);
+						debugln();
+					#endif
+				}
+			}
+			phase++;
+			return SHENQI2_WRITE_TIME;
+		case SHENQI2_BIND_RX:
+			XN297_SetTxRxMode(TXRX_OFF);
+			XN297_SetTxRxMode(RX_EN);
+			phase = SHENQI2_BIND;
+			return SHENQI2_PACKET_PERIOD - SHENQI2_WRITE_TIME;
+		default: //SHENQI2_DATA
+			//Since I don't know the order of the channels, I'm hopping on all the channels quickly
+			//Refresh rate from the motorcycle perspective is 32ms instead of 8ms...
+			XN297_Hopping(hopping_frequency_no);
+			hopping_frequency_no++;
+			hopping_frequency_no &= 0x0F;
+			SHENQI2_send_packet();
+			if(hopping_frequency_no%4 == 0)
+				packet_count++;
+			return SHENQI2_PACKET_PERIOD/4;
+	}
+	return 0;
+}
+
+void SHENQI2_init()
+{
+	BIND_IN_PROGRESS;
+	SHENQI2_initialize_txid();
+	SHENQI2_RF_init();
+
+	bind_counter = SHENQI2_BIND_COUNT;
+	phase = SHENQI2_BIND;
+	hopping_frequency_no = 0;
+}
+
+#endif
+/*
+XN297 1Mb Enhanced,Acked,Scrambled
+
+Bind
+---
+RX on channel: 44, Time:  2890us P: 34 51 70 02 00 00 00 00
+RX on channel: 44, Time:  1780us P: 34 51 70 02 00 00 00 00
+RX on channel: 44, Time:  1773us P: 34 51 70 02 00 00 00 00
+RX on channel: 44, Time:  1772us P: 34 51 70 02 00 00 00 00
+RX on channel: 44, Time:  2889us P: 35 51 70 02 00 00 00 00
+RX on channel: 44, Time:  1769us P: 35 51 70 02 00 00 00 00
+RX on channel: 44, Time:  1774us P: 35 51 70 02 00 00 00 00
+RX on channel: 44, Time:  1771us P: 35 51 70 02 00 00 00 00
+RX on channel: 44, Time:  2894us P: 36 51 70 02 00 00 00 00
+
+A= 74 D1 3A F5 6C
+RF:44
+Timing: 1772µs between the same 4 packets, 2892µs to the next packet, 8208µs between 2 packets
+Request ack, if no ack repeat the packet 4 times
+
+P[0] = counter 00..0F | 30 bind
+P[1] = TXID[0]
+P[2] = TXID[1]
+P[3] = TXID[2]
+P[4] = RXID[0]
+P[5] = RXID[1]
+P[6] = TH 00..1F, Break 30, 40 ST_right, 80 ST_left
+P[7] = 00?
+
+Answer from motorcycle:
+P: 51 70 02 46 BE 00 00 00
+P[0] = TXID[0]
+P[1] = TXID[1]
+P[2] = TXID[2]
+P[3] = RXID[0]
+P[4] = RXID[1]
+P[5] = 00
+P[6] = 00
+P[7] = 00
+
+Normal packets
+---
+A= 74 D1 3A F5 6C
+RF:5,9,14,15,23,28,33,39,42,44,51,57,61,66,72,76
+RF:\x05\x09\x0E\x0F\x17\x1C\x21\x27\x2A\x2C\x33\x39\x3D\x42\x48\x4C
+- order of the channels is unknown and vary over time
+- send 16 times on each channel and switch (counter 00..0F)
+Timing:1772µs between the same 4 packets, 2892µs to the next packet, 8208µs between 2 packets
+Timing:8208 between packets if acked
+P: 00 51 70 02 46 BE 00 00
+P[0] = counter 00..0F
+P[1] = TXID[0]
+P[2] = TXID[1]
+P[3] = TXID[2]
+P[4] = RXID[0]
+P[5] = RXID[1]
+P[6] = TH 00..1F, Break 30, 40 ST_right, 80 ST_left
+P[7] = 00?
+*/

Multiprotocol/SLT_ccnrf.ino

@@ -19,6 +19,7 @@
 #include "iface_nrf250k.h"
 
 //#define SLT_Q200_FORCE_ID
+//#define SLT_V1_4_FORCE_ID
 
 // For code readability
 #define SLT_PAYLOADSIZE_V1		7
@@ -73,12 +74,12 @@ static void __attribute__((unused)) SLT_set_freq(void)
 	}
 
 	// Unique freq
-	uint8_t max_freq=0x50;	//V1 and V2
+	uint8_t max_freq = 0x50;	//V1 and V2
-	if(sub_protocol==Q200)
+	if(sub_protocol == Q200)
 		max_freq=45;
 	for (uint8_t i = 0; i < SLT_NFREQCHANNELS; ++i)
 	{
-		if(sub_protocol==Q200 && hopping_frequency[i] >= max_freq)
+		if(sub_protocol == Q200 && hopping_frequency[i] >= max_freq)
 			hopping_frequency[i] = hopping_frequency[i] - max_freq + 0x03;
 		uint8_t done = 0;
 		while (!done)
@@ -94,15 +95,15 @@ static void __attribute__((unused)) SLT_set_freq(void)
 				}
 		}
 	}
-	#if 0
+	#ifdef DEBUG_SERIAL
 		debug("CH:");
 		for (uint8_t i = 0; i < SLT_NFREQCHANNELS; ++i)
-			debug(" %02X", hopping_frequency[i]);
+			debug(" %02X(%d)", hopping_frequency[i], hopping_frequency[i]);
 		debugln();
 	#endif
 	
 	//Bind channel
-	hopping_frequency[SLT_NFREQCHANNELS]=SLT_BIND_CHANNEL;
+	hopping_frequency[SLT_NFREQCHANNELS] = SLT_BIND_CHANNEL;
 	
 	//Calib all channels
 	NRF250K_HoppingCalib(SLT_NFREQCHANNELS+1);
@@ -153,35 +154,38 @@ static void __attribute__((unused)) SLT_build_packet()
 
 	//->V1 stops here
 
-	if(sub_protocol==Q200)
+	if(sub_protocol == Q200)
 		packet[6] =  GET_FLAG(CH9_SW , FLAG_Q200_FMODE)
 					|GET_FLAG(CH10_SW, FLAG_Q200_FLIP)
 					|GET_FLAG(CH11_SW, FLAG_Q200_VIDON)
 					|GET_FLAG(CH12_SW, FLAG_Q200_VIDOFF);
-	else if(sub_protocol==MR100 || sub_protocol==Q100)
+	else if(sub_protocol == MR100 || sub_protocol == Q100)
 		packet[6] =  GET_FLAG(CH9_SW , FLAG_MR100_FMODE)
 					|GET_FLAG(CH10_SW, FLAG_MR100_FLIP)
 					|GET_FLAG(CH11_SW, FLAG_MR100_VIDEO)	// Does not exist on the Q100 but...
 					|GET_FLAG(CH12_SW, FLAG_MR100_PICTURE);	// Does not exist on the Q100 but...
-	packet[7]=convert_channel_8b(CH7);
+	packet[7] = convert_channel_8b(CH7);
-	packet[8]=convert_channel_8b(CH8);
+	packet[8] = convert_channel_8b(CH8);
-  if(sub_protocol==RF_SIM) {
+	if(sub_protocol == RF_SIM)
-    packet[9]=convert_channel_8b(CH9);
+	{
-    packet[10]=convert_channel_8b(CH10);
+		packet[9]  = convert_channel_8b(CH9);
-  } else {
+		packet[10] = convert_channel_8b(CH10);
-    packet[9]=0xAA;       //normal mode for Q100/Q200, unknown for V2/MR100
-    packet[10]=0x00;      //normal mode for Q100/Q200, unknown for V2/MR100
-  }
-	if((sub_protocol==Q100 || sub_protocol==Q200) && CH13_SW)
-	{//Calibrate
-		packet[9]=0x77;			//enter calibration
-		if(calib_counter>=20 && calib_counter<=25)	// 7 packets for Q100 / 3 packets for Q200
-			packet[10]=0x20;	//launch calibration
-		calib_counter++;
-		if(calib_counter>250) calib_counter=250;
 	}
 	else
-		calib_counter=0;
+	{
+		packet[9]  = 0xAA;		//normal mode for Q100/Q200, unknown for V2/MR100
+		packet[10] = 0x00;		//normal mode for Q100/Q200, unknown for V2/MR100
+	}
+	if((sub_protocol == Q100 || sub_protocol == Q200) && CH13_SW)
+	{//Calibrate
+		packet[9] = 0x77;			//enter calibration
+		if(calib_counter >= 20 && calib_counter <= 25)	// 7 packets for Q100 / 3 packets for Q200
+			packet[10] = 0x20;	//launch calibration
+		calib_counter++;
+		if(calib_counter > 250) calib_counter = 250;
+	}
+	else
+		calib_counter = 0;
 }
 
 static void __attribute__((unused)) SLT_send_bind_packet()
@@ -192,8 +196,8 @@ static void __attribute__((unused)) SLT_send_bind_packet()
 	NRF250K_SetPower();
 	BIND_DONE;
 	NRF250K_SetTXAddr((uint8_t *)"\x7E\xB8\x63\xA9", SLT_TXID_SIZE);
-	memcpy((void*)packet,(void*)rx_tx_addr,SLT_TXID_SIZE);
+	memcpy((void*)packet, (void*)rx_tx_addr, SLT_TXID_SIZE);
-	if(phase==SLT_BIND2)
+	if(phase == SLT_BIND2)
 		SLT_send_packet(SLT_TXID_SIZE);
 	else // SLT_BIND1
 		SLT_send_packet(SLT_PAYLOADSIZE_V2);
@@ -224,9 +228,9 @@ uint16_t SLT_callback()
 		case SLT_DATA2:
 			phase++;
 			SLT_send_packet(packet_length);
-			if(sub_protocol==SLT_V1)
+			if(sub_protocol == SLT_V1)
 				return SLT_V1_TIMING_PACKET;
-			if(sub_protocol==SLT_V1_4)
+			if(sub_protocol == SLT_V1_4)
 			{
 				phase++;						//Packets are sent two times only
 				return SLT_V1_4_TIMING_PACKET;
@@ -238,24 +242,24 @@ uint16_t SLT_callback()
 			if (++packet_count >= 100)
 			{// Send bind packet
 				packet_count = 0;
-				if(sub_protocol==SLT_V1||sub_protocol==SLT_V1_4)
+				if(sub_protocol == SLT_V1 || sub_protocol == SLT_V1_4)
 				{
-					phase=SLT_BIND2;
+					phase = SLT_BIND2;
 					return SLT_V1_TIMING_BIND2;
 				}
 				//V2
-				phase=SLT_BIND1;
+				phase = SLT_BIND1;
 				return SLT_V2_TIMING_BIND1;
 			}
 			else
 			{// Continue to send normal packets
 				phase = SLT_BUILD;
-				if(sub_protocol==SLT_V1)
+				if(sub_protocol == SLT_V1)
-					return 20000-SLT_TIMING_BUILD;
+					return 20000 - SLT_TIMING_BUILD;
 				if(sub_protocol==SLT_V1_4)
-					return 18000-SLT_TIMING_BUILD-SLT_V1_4_TIMING_PACKET;
+					return 18000 - SLT_TIMING_BUILD - SLT_V1_4_TIMING_PACKET;
 				//V2
-				return 13730-SLT_TIMING_BUILD;
+				return 13730 - SLT_TIMING_BUILD;
 			}
 		case SLT_BIND1:
 			SLT_send_bind_packet();
@@ -264,12 +268,12 @@ uint16_t SLT_callback()
 		case SLT_BIND2:
 			SLT_send_bind_packet();
 			phase = SLT_BUILD;
-			if(sub_protocol==SLT_V1)
+			if(sub_protocol == SLT_V1)
-				return 20000-SLT_TIMING_BUILD-SLT_V1_TIMING_BIND2;
+				return 20000 - SLT_TIMING_BUILD - SLT_V1_TIMING_BIND2;
-			if(sub_protocol==SLT_V1_4)
+			if(sub_protocol == SLT_V1_4)
-				return 18000-SLT_TIMING_BUILD-SLT_V1_TIMING_BIND2-SLT_V1_4_TIMING_PACKET;
+				return 18000 - SLT_TIMING_BUILD - SLT_V1_TIMING_BIND2 - SLT_V1_4_TIMING_PACKET;
 			//V2
-			return 13730-SLT_TIMING_BUILD-SLT_V2_TIMING_BIND1-SLT_V2_TIMING_BIND2;
+			return 13730 - SLT_TIMING_BUILD - SLT_V2_TIMING_BIND1 - SLT_V2_TIMING_BIND2;
 	}
 	return 19000;
 }
@@ -280,35 +284,26 @@ void SLT_init()
 	packet_count = 0;
 	packet_sent = 0;
 	hopping_frequency_no = 0;
-	if(sub_protocol==Q200)
+
-	{ //Q200: Force high part of the ID otherwise it won't bind
+	if(sub_protocol == SLT_V1)
-		rx_tx_addr[0]=0x01;
-		rx_tx_addr[1]=0x02;
-		#ifdef SLT_Q200_FORCE_ID	// ID taken from TX dumps
-			rx_tx_addr[0]=0x01;rx_tx_addr[1]=0x02;rx_tx_addr[2]=0x6A;rx_tx_addr[3]=0x31;
-		/*	rx_tx_addr[0]=0x01;rx_tx_addr[1]=0x02;rx_tx_addr[2]=0x0B;rx_tx_addr[3]=0x57;*/
-		#endif
-	}
-	SLT_RF_init();
-	SLT_set_freq();
-	phase = SLT_BUILD;
-	if(sub_protocol==SLT_V1)
 	{
 		packet_length = SLT_PAYLOADSIZE_V1;
 		#ifdef MULTI_SYNC
 			packet_period = 20000+2*SLT_V1_TIMING_PACKET;		//22ms
 		#endif
 	}
-	else if(sub_protocol==SLT_V1_4)
+	else if(sub_protocol == SLT_V1_4)
 	{
 		packet_length = SLT_PAYLOADSIZE_V1_4;
 		#ifdef MULTI_SYNC
 			packet_period = 18000;								//18ms
 		#endif
-		//Test IDs
+		 //Force high part of the ID otherwise the RF frequencies do not match, only tested the 2 last bytes...
-		MProtocol_id = MProtocol_id_master ^ (1<<RX_num);
+		rx_tx_addr[0]=0xF4;
-		set_rx_tx_addr(MProtocol_id);
+		rx_tx_addr[1]=0x71;
-		debugln("Try ID: %lx", MProtocol_id);
+		#ifdef SLT_V1_4_FORCE_ID	// ID taken from TX dumps
+			memcpy(rx_tx_addr,"\xF4\x71\x8D\x01",SLT_TXID_SIZE);
+		#endif
 	}
 	else //V2
 	{
@@ -317,6 +312,21 @@ void SLT_init()
 			packet_period = 13730+2*SLT_V2_TIMING_PACKET;		//~18ms
 		#endif
 	}
+
+	if(sub_protocol == Q200)
+	{ //Q200: Force high part of the ID otherwise it won't bind
+		rx_tx_addr[0]=0x01;
+		rx_tx_addr[1]=0x02;
+		#ifdef SLT_Q200_FORCE_ID	// ID taken from TX dumps
+			rx_tx_addr[0]=0x01;rx_tx_addr[1]=0x02;rx_tx_addr[2]=0x6A;rx_tx_addr[3]=0x31;
+		/*	rx_tx_addr[0]=0x01;rx_tx_addr[1]=0x02;rx_tx_addr[2]=0x0B;rx_tx_addr[3]=0x57;*/
+		#endif
+	}
+
+	SLT_RF_init();
+	SLT_set_freq();
+
+	phase = SLT_BUILD;
 }
 
 #endif

Multiprotocol/UDIRC_ccnrf.ino

@@ -0,0 +1,184 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+//Models: UDIRC UD160x(PRO), Pinecone Models SG-160x, Eachine EAT15
+
+#if defined(UDIRC_CCNRF_INO)
+
+#include "iface_xn297.h"
+
+#define FORCE_UDIRC_ORIGINAL_ID
+
+#define UDIRC_PAYLOAD_SIZE			15
+#define UDIRC_RF_NUM_CHANNELS		4
+#define UDIRC_PACKET_PERIOD			21000
+#define UDIRC_BIND_COUNT			2000
+#define UDIRC_P1_P2_TIME			5000
+#define UDIRC_WRITE_TIME			1500
+
+enum {
+	UDIRC_DATA1=0,
+	UDIRC_DATA2,
+	UDIRC_DATA3,
+	UDIRC_RX,
+};
+
+static void __attribute__((unused)) UDIRC_send_packet()
+{
+	if(rf_ch_num==0)
+	{
+		XN297_Hopping(hopping_frequency_no);
+		debug("H %d ",hopping_frequency_no);
+		hopping_frequency_no++;
+		hopping_frequency_no &= 3;
+	}
+
+	memset(&packet[3], 0x00, 12);
+	if(bind_counter)
+	{//Bind in progress
+		bind_counter--;
+		if(bind_counter)
+		{//Bind
+			packet[0] = 0x01;
+			memcpy(&packet[1],rx_tx_addr,5);
+		}
+		else
+		{//Switch to normal
+			rf_ch_num = 1;
+			BIND_DONE;
+			XN297_SetTXAddr(rx_tx_addr, 5);
+			XN297_SetRXAddr(rx_tx_addr, UDIRC_PAYLOAD_SIZE);
+		}
+	}
+	if(!bind_counter)
+	{//Normal
+		packet[0] = 0x08;
+		//Channels SG-16xx: ST/TH/CH4 /CH3  /UNK/UNK/UNK/UNK/GYRO/ST_TRIM/ST_DR
+		//Channels EAT15  : ST/TH/RATE/LIGHT/UNK/UNK/UNK/UNK/GYRO/ST_TRIM/ST_DR
+		for(uint8_t i=0; i<12; i++)
+			packet[i+1] = convert_channel_16b_limit(i,0,200);
+		//Just for now let's set the additional channels to 0
+		packet[5] = packet[6] = packet[7] = packet[8] = 0;
+	}
+	packet[12] = GET_FLAG(CH12_SW,  0x40)						//TH.REV
+				|GET_FLAG(CH13_SW,  0x80);						//ST.REV
+	//packet[13] = 00; //Unknown, future flags?
+	for(uint8_t i=0;i<UDIRC_PAYLOAD_SIZE-1;i++)
+		packet[14] += packet[i];
+	// Send
+	XN297_SetFreqOffset();
+	XN297_SetPower();
+	XN297_SetTxRxMode(TX_EN);
+	XN297_WriteEnhancedPayload(packet, UDIRC_PAYLOAD_SIZE,false);
+	#ifdef DEBUG_SERIAL
+		for(uint8_t i=0; i < UDIRC_PAYLOAD_SIZE; i++)
+			debug("%02X ", packet[i]);
+		debugln();
+	#endif
+}
+
+static void __attribute__((unused)) UDIRC_initialize_txid()
+{
+	#ifdef FORCE_UDIRC_ORIGINAL_ID
+		if(RX_num)
+		{
+			rx_tx_addr[0] = 0xD0;
+			rx_tx_addr[1] = 0x06;
+			rx_tx_addr[2] = 0x00;
+			rx_tx_addr[3] = 0x00;
+			rx_tx_addr[4] = 0x81;
+		}
+		else
+		{
+			rx_tx_addr[0] = 0xF6;
+			rx_tx_addr[1] = 0x96;
+			rx_tx_addr[2] = 0x01;
+			rx_tx_addr[3] = 0x00;
+			rx_tx_addr[4] = 0x81;
+		}
+		hopping_frequency[0] = 45;
+		hopping_frequency[1] = 59;
+		hopping_frequency[2] = 52;
+		hopping_frequency[3] = 67;
+	#endif
+}
+
+static void __attribute__((unused)) UDIRC_RF_init()
+{
+	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_250K);
+	//Bind address
+	XN297_SetTXAddr((uint8_t*)"\x01\x03\x05\x07\x09", 5);
+	XN297_SetRXAddr((uint8_t*)"\x01\x03\x05\x07\x09", UDIRC_PAYLOAD_SIZE);
+	XN297_HoppingCalib(UDIRC_RF_NUM_CHANNELS);
+}
+
+uint16_t UDIRC_callback()
+{
+	bool rx;
+	switch(phase)
+	{
+		case UDIRC_DATA1:
+			rx = XN297_IsRX();
+			XN297_SetTxRxMode(TXRX_OFF);
+			#ifdef MULTI_SYNC
+				telemetry_set_input_sync(UDIRC_PACKET_PERIOD);
+			#endif
+			UDIRC_send_packet();
+			if(rx)
+			{
+				uint8_t val=XN297_ReadEnhancedPayload(packet_in, UDIRC_PAYLOAD_SIZE);
+				debug("RX(%d):",val);
+				if(val != 255)
+				{
+					rf_ch_num = 1;
+					if(bind_counter)
+						bind_counter=1;
+					#ifdef DEBUG_SERIAL
+						for(uint8_t i=0; i < UDIRC_PAYLOAD_SIZE; i++)
+							debug(" %02X", packet_in[i]);
+					#endif
+				}
+				debugln("");
+			}
+			phase++;
+			return UDIRC_P1_P2_TIME;
+		case UDIRC_DATA2:
+			//Resend packet
+			XN297_ReSendPayload();
+			phase++;
+			return UDIRC_WRITE_TIME;
+		default: //UDIRC_RX
+			//Wait for the packet transmission to finish
+			while(XN297_IsPacketSent()==false);
+			//Switch to RX
+			XN297_SetTxRxMode(TXRX_OFF);
+			XN297_SetTxRxMode(RX_EN);
+			phase = UDIRC_DATA1;
+			return UDIRC_PACKET_PERIOD - UDIRC_P1_P2_TIME - UDIRC_WRITE_TIME;
+	}
+	return 0;
+}
+
+void UDIRC_init()
+{
+	UDIRC_initialize_txid();
+	UDIRC_RF_init();
+
+	bind_counter = IS_BIND_IN_PROGRESS ? UDIRC_BIND_COUNT : 1;
+	phase = UDIRC_DATA1;
+	hopping_frequency_no = 0;
+	rf_ch_num = 0;
+}
+
+#endif

Multiprotocol/Validate.h

@@ -326,6 +326,7 @@
 	#undef	HONTAI_NRF24L01_INO
 	#undef	JIABAILE_NRF24L01_INO
 	#undef	JJRC345_NRF24L01_INO
+	#undef	KAMTOM_NRF24L01_INO
 	#undef	KN_NRF24L01_INO
 	#undef	KYOSHO2_NRF24L01_INO
 	#undef	LOLI_NRF24L01_INO
@@ -336,6 +337,7 @@
 	#undef	REALACC_NRF24L01_INO
 	#undef	SGF22_NRF24L01_INO
 	#undef	SHENQI_NRF24L01_INO
+	#undef	SHENQI2_NRF24L01_INO
 	#undef	SYMAX_NRF24L01_INO
 	#undef	V2X2_NRF24L01_INO
 	#undef	V761_NRF24L01_INO
@@ -355,7 +357,9 @@
 	#undef	Q303_CCNRF_INO
 	#undef	Q90C_CCNRF_INO
 	#undef	SLT_CCNRF_INO
+	#undef	UDIRC_CCNRF_INO
 	#undef	V911S_CCNRF_INO
+	#undef	WL91X_CCNRF_INO
 	#undef	XK_CCNRF_INO
 	#undef	XK2_CCNRF_INO
 #endif
@@ -390,7 +394,11 @@
 	#undef	KYOSHO3_CYRF6936_INO
 	#undef	MOULDKG_NRF24L01_INO
 	#undef	SHENQI_NRF24L01_INO
+	#undef	SHENQI2_NRF24L01_INO
 	#undef	JIABAILE_NRF24L01_INO
+	#undef	UDIRC_CCNRF_INO
+	#undef	KAMTOM_NRF24L01_INO
+	#undef	WL91X_CCNRF_INO
 #endif
 
 #ifdef MULTI_SURFACE
@@ -486,6 +494,7 @@
 	#undef PROPEL_HUB_TELEMETRY
 	#undef OMP_HUB_TELEMETRY
 	#undef V761_HUB_TELEMETRY
+	#undef KAMTOM_HUB_TELEMETRY
 	#undef YUXIANG_HUB_TELEMETRY
 	#undef RLINK_HUB_TELEMETRY
 	#undef DSM_RX_CYRF6936_INO
@@ -525,6 +534,9 @@
 	#if not defined(V761_NRF24L01_INO)
 		#undef V761_HUB_TELEMETRY
 	#endif
+	#if not defined(KAMTOM_NRF24L01_INO)
+		#undef KAMTOM_HUB_TELEMETRY
+	#endif
 	#if not defined(YUXIANG_NRF24L01_INO)
 		#undef YUXIANG_HUB_TELEMETRY
 	#endif
@@ -585,7 +597,7 @@
 		//protocols using FRSKYD user frames
 		#undef HUB_TELEMETRY 
 	#endif
-	#if not defined(HOTT_FW_TELEMETRY) && not defined(DSM_TELEMETRY) && not defined(SPORT_TELEMETRY) && not defined(HUB_TELEMETRY) && not defined(HUBSAN_HUB_TELEMETRY) && not defined(BUGS_HUB_TELEMETRY) && not defined(NCC1701_HUB_TELEMETRY) && not defined(BAYANG_HUB_TELEMETRY) && not defined(CABELL_HUB_TELEMETRY) && not defined(RLINK_HUB_TELEMETRY) && not defined(AFHDS2A_HUB_TELEMETRY) && not defined(AFHDS2A_FW_TELEMETRY) && not defined(MULTI_TELEMETRY) && not defined(MULTI_STATUS) && not defined(HITEC_HUB_TELEMETRY) && not defined(HITEC_FW_TELEMETRY) && not defined(SCANNER_TELEMETRY) && not defined(FRSKY_RX_TELEMETRY) && not defined(AFHDS2A_RX_TELEMETRY) && not defined(BAYANG_RX_TELEMETRY) && not defined(DEVO_HUB_TELEMETRY) && not defined(PROPEL_HUB_TELEMETRY) && not defined(OMP_HUB_TELEMETRY) && not defined(V761_HUB_TELEMETRY) && not defined(YUXIANG_HUB_TELEMETRY) && not defined(WFLY2_HUB_TELEMETRY) && not defined(LOLI_HUB_TELEMETRY) && not defined(MLINK_HUB_TELEMETRY) && not defined(MLINK_FW_TELEMETRY) && not defined(MT99XX_HUB_TELEMETRY) && not defined(MULTI_CONFIG_INO)
+	#if not defined(HOTT_FW_TELEMETRY) && not defined(DSM_TELEMETRY) && not defined(SPORT_TELEMETRY) && not defined(HUB_TELEMETRY) && not defined(HUBSAN_HUB_TELEMETRY) && not defined(BUGS_HUB_TELEMETRY) && not defined(NCC1701_HUB_TELEMETRY) && not defined(BAYANG_HUB_TELEMETRY) && not defined(CABELL_HUB_TELEMETRY) && not defined(RLINK_HUB_TELEMETRY) && not defined(AFHDS2A_HUB_TELEMETRY) && not defined(AFHDS2A_FW_TELEMETRY) && not defined(MULTI_TELEMETRY) && not defined(MULTI_STATUS) && not defined(HITEC_HUB_TELEMETRY) && not defined(HITEC_FW_TELEMETRY) && not defined(SCANNER_TELEMETRY) && not defined(FRSKY_RX_TELEMETRY) && not defined(AFHDS2A_RX_TELEMETRY) && not defined(BAYANG_RX_TELEMETRY) && not defined(DEVO_HUB_TELEMETRY) && not defined(PROPEL_HUB_TELEMETRY) && not defined(OMP_HUB_TELEMETRY) && not defined(V761_HUB_TELEMETRY) && not defined(KAMTOM_HUB_TELEMETRY) && not defined(YUXIANG_HUB_TELEMETRY) && not defined(WFLY2_HUB_TELEMETRY) && not defined(LOLI_HUB_TELEMETRY) && not defined(MLINK_HUB_TELEMETRY) && not defined(MLINK_FW_TELEMETRY) && not defined(MT99XX_HUB_TELEMETRY) && not defined(MULTI_CONFIG_INO)
 		#undef TELEMETRY
 		#undef INVERT_TELEMETRY
 		#undef MULTI_TELEMETRY

Multiprotocol/WL91X_ccnrf.ino

@@ -0,0 +1,96 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#if defined(WL91X_CCNRF_INO)
+
+#include "iface_xn297.h"
+
+//#define FORCE_WL91X_ORIGINAL_ID
+
+#define WL91X_PAYLOAD_SIZE		9
+#define WL91X_RF_NUM_CHANNELS	3
+#define WL91X_PACKET_PERIOD		2594
+
+static void __attribute__((unused)) WL91X_send_packet()
+{
+	uint8_t val;
+
+	//RF freq
+	XN297_Hopping(hopping_frequency_no++);
+	hopping_frequency_no %= WL91X_RF_NUM_CHANNELS;
+
+	//Sticks
+	val = convert_channel_16b_limit(CH2,0x21,0xE0);			//THR forward 00..5F, backward 80..DF
+	if(val < 128) val = 127 - val;
+	packet[0] = val - 0x80;
+	val = convert_channel_s8b(CH1);							//ST right 00..7F, left 80..FF
+	packet[1] = val - 0x80;
+	//Trims
+	val = convert_channel_s8b(CH3);							//ST_Trim centered=80, increment/decrement=4, right 04..7C, left 84..FC
+	packet[2] = val - 0x80;
+	packet[3] = convert_channel_16b_limit(CH4,0x00,0x70);	//TH_Trim increment/decrement=3, 00..39..6F
+	//TX_ID
+	memcpy(&packet[4], rx_tx_addr, 4);
+	//Checksum
+	val = 0;
+	for(uint8_t i=0; i<WL91X_PAYLOAD_SIZE-1; i++)
+		val += packet[i];
+	packet[8] = val;
+
+	//Send
+	XN297_SetPower();
+	XN297_SetFreqOffset();
+	XN297_SetTxRxMode(TX_EN);
+	XN297_WritePayload(packet, WL91X_PAYLOAD_SIZE);
+	#ifdef DEBUG_SERIAL
+		for(uint8_t i=0; i < WL91X_PAYLOAD_SIZE; i++)
+			debug("%02X ", packet[i]);
+		debugln();
+	#endif
+}
+
+static void __attribute__((unused)) WL91X_RF_init()
+{
+	XN297_Configure(XN297_CRCEN, XN297_UNSCRAMBLED, XN297_250K);
+	XN297_HoppingCalib(WL91X_RF_NUM_CHANNELS);
+	XN297_SetTXAddr((uint8_t*)"\x46\x14\x7B\x08", 4);
+}
+
+static void __attribute__((unused)) WL91X_initialize_txid()
+{
+	#ifdef FORCE_WL91X_ORIGINAL_ID
+		memcpy(rx_tx_addr, (uint8_t*)"\x00\x1E\x33\x02",4);
+	#endif
+	memcpy(hopping_frequency, (uint8_t*)"\x1A\x3B\x3B",3);	//26,59,59
+}
+
+uint16_t WL91X_callback()
+{
+	#ifdef MULTI_SYNC
+		telemetry_set_input_sync(WL91X_PACKET_PERIOD);
+	#endif
+	WL91X_send_packet();
+	return WL91X_PACKET_PERIOD;
+}
+
+void WL91X_init()
+{
+	BIND_DONE;	//No bind for this protocol
+	WL91X_initialize_txid();
+	WL91X_RF_init();
+	hopping_frequency_no = 0;
+}
+
+#endif

Multiprotocol/XK2_ccnrf.ino

@@ -71,9 +71,13 @@ static void __attribute__((unused)) XK2_send_packet()
 		}
 		//Flags
 		packet[5] = GET_FLAG(CH5_SW, 0x01)								//Rate
-				  | GET_FLAG(CH6_SW, 0x08)								//Mode
 				  | GET_FLAG(CH7_SW, 0x20)								//Hover
 				  | GET_FLAG(CH8_SW, 0x40);								//Light
+		if(CH6_SW)
+			packet[5] |= 0x10;											//Gyro off (senior mode)
+		else if(Channel_data[CH6] > CHANNEL_MIN_COMMAND)
+			packet[5] |= 0x08;											//3D
+
 		//Telemetry not received=00, Telemetry received=01 but sometimes switch to 1 even if telemetry is not there...
 		packet[6] = 0x00;
 		//RXID checksum
@@ -200,7 +204,7 @@ uint16_t XK2_callback()
 			}
 			return 1000;
 		case XK2_DATA_PREP:
-			crc8=eeprom_read_byte((EE_ADDR)(XK2_EEPROM_OFFSET+RX_num));
+			crc8 = eeprom_read_byte((EE_ADDR)(XK2_EEPROM_OFFSET+RX_num));
 			debugln("R:RX_ID=%02X",crc8);
 			XN297_SetTxRxMode(TXRX_OFF);
 			XN297_SetTxRxMode(TX_EN);

Multiprotocol/XN297_EMU.ino

@@ -207,6 +207,27 @@ static void __attribute__((unused)) XN297_SetTxRxMode(enum TXRX_State mode)
 	#endif
 }
 
+#ifdef CC2500_INSTALLED
+uint8_t XN297_Buffer[32];
+uint8_t XN297_Buffer_Len = 0;
+
+static void __attribute__((unused)) XN297_SendCC2500Payload()
+{
+	// stop TX/RX
+	CC2500_Strobe(CC2500_SIDLE);
+	// flush tx FIFO
+	CC2500_Strobe(CC2500_SFTX);
+	// packet length
+	CC2500_WriteReg(CC2500_06_PKTLEN, XN297_Buffer_Len + 4);  // Packet len, fix packet len
+	// xn297L preamble
+	CC2500_WriteRegisterMulti(CC2500_3F_TXFIFO, (uint8_t*)"\x0C\x71\x0F\x55", 4);
+	// xn297 packet
+	CC2500_WriteRegisterMulti(CC2500_3F_TXFIFO, XN297_Buffer, XN297_Buffer_Len);
+	// transmit
+	CC2500_Strobe(CC2500_STX);
+}
+#endif
+
 static void __attribute__((unused)) XN297_SendPayload(uint8_t* msg, uint8_t len)
 {
 	#ifdef NRF24L01_INSTALLED
@@ -220,22 +241,25 @@ static void __attribute__((unused)) XN297_SendPayload(uint8_t* msg, uint8_t len)
 	#ifdef CC2500_INSTALLED
 		if(xn297_rf == XN297_CC2500)
 		{
-			// stop TX/RX
+			memcpy(XN297_Buffer, msg, len);
-			CC2500_Strobe(CC2500_SIDLE);
+			XN297_Buffer_Len = len;
-			// flush tx FIFO
+			XN297_SendCC2500Payload();
-			CC2500_Strobe(CC2500_SFTX);
-			// packet length
-			CC2500_WriteReg(CC2500_06_PKTLEN, len + 4);  // Packet len, fix packet len
-			// xn297L preamble
-			CC2500_WriteRegisterMulti(CC2500_3F_TXFIFO, (uint8_t*)"\x0C\x71\x0F\x55", 4);
-			// xn297 packet
-			CC2500_WriteRegisterMulti(CC2500_3F_TXFIFO, msg, len);
-			// transmit
-			CC2500_Strobe(CC2500_STX);
 		}
 	#endif
 }
 
+static void __attribute__((unused)) XN297_ReSendPayload()
+{
+	#ifdef NRF24L01_INSTALLED
+		if(xn297_rf == XN297_NRF)
+			NRF24L01_Strobe(NRF24L01_E3_REUSE_TX_PL);
+	#endif
+	#ifdef CC2500_INSTALLED
+		if(xn297_rf == XN297_CC2500)
+			XN297_SendCC2500Payload();
+	#endif
+}
+
 static void __attribute__((unused)) XN297_WritePayload(uint8_t* msg, uint8_t len)
 {
 	uint8_t buf[32];
@@ -329,9 +353,9 @@ static void __attribute__((unused)) XN297_WriteEnhancedPayload(uint8_t* msg, uin
 
 		last++;
 		buf[last] = bit_reverse(msg[len-1]) << 6; // last 2 bit of payload
-		if(xn297_scramble_enabled)
-			buf[last] ^= xn297_scramble[scramble_index++] & 0xc0;
 	}
+	if(xn297_scramble_enabled)
+		buf[last] ^= xn297_scramble[scramble_index++] & 0xc0;
 
 	// crc
 	if (xn297_crc)
@@ -351,8 +375,7 @@ static void __attribute__((unused)) XN297_WriteEnhancedPayload(uint8_t* msg, uin
 		buf[last++] = (crc & 0xff) << 6;
 	}
 	pid++;
-	if(pid>3)
+	pid &= 0x03;
-		pid=0;
 
 	// send packet
 	XN297_SendPayload(buf, last);

Multiprotocol/_Config.h

@@ -246,6 +246,7 @@
 #define	HONTAI_NRF24L01_INO
 #define JIABAILE_NRF24L01_INO
 #define	JJRC345_NRF24L01_INO
+#define	KAMTOM_NRF24L01_INO
 #define	KN_NRF24L01_INO
 #define	KYOSHO2_NRF24L01_INO
 #define	LOLI_NRF24L01_INO
@@ -256,6 +257,7 @@
 #define	REALACC_NRF24L01_INO
 #define	SGF22_NRF24L01_INO
 #define	SHENQI_NRF24L01_INO
+#define	SHENQI2_NRF24L01_INO
 #define	SYMAX_NRF24L01_INO
 #define	V2X2_NRF24L01_INO
 #define	V761_NRF24L01_INO
@@ -273,7 +275,9 @@
 #define	Q303_CCNRF_INO
 #define	Q90C_CCNRF_INO
 #define	SLT_CCNRF_INO
+#define	UDIRC_CCNRF_INO
 #define	V911S_CCNRF_INO
+#define	WL91X_CCNRF_INO
 #define	XK_CCNRF_INO
 #define	XK2_CCNRF_INO
 
@@ -349,6 +353,7 @@
 #define NCC1701_HUB_TELEMETRY		// Use FrSkyD Hub format to send telemetry to TX
 #define OMP_HUB_TELEMETRY			// Use FrSkyD Hub format to send telemetry to TX
 #define V761_HUB_TELEMETRY			// Use FrSkyD Hub format to send telemetry to TX
+#define KAMTOM_HUB_TELEMETRY		// Use FrSkyD Hub format to send telemetry to TX
 #define YUXIANG_HUB_TELEMETRY
 #define PROPEL_HUB_TELEMETRY		// Use FrSkyD Hub format to send telemetry to TX
 #define CABELL_HUB_TELEMETRY		// Use FrSkyD Hub format to send telemetry to TX
@@ -695,6 +700,7 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 		FX620
 		FX9630
 		Q560
+		QF012
 	PROTO_FY326
 		FY326
 		FY319
@@ -744,6 +750,8 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 		SKYTMBLR
 	PROTO_JOYSWAY
 		NONE
+	PROTO_KAMTOM
+		NONE
 	PROTO_KF606
 		KF606_KF606
 		KF606_MIG320
@@ -830,6 +838,8 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
   		J20
 	PROTO_SHENQI
 		NONE
+	PROTO_SHENQI2
+		NONE
 	PROTO_SKYARTEC
 		NONE
 	PROTO_SLT
@@ -845,6 +855,8 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 		SYMAX5C
 	PROTO_TRAXXAS
 		NONE
+	PROTO_UDIRC
+		NONE
 	PROTO_V2X2
 		V2X2
 		JXD506

Multiprotocol/iface_xn297.h

@@ -28,6 +28,7 @@ static void __attribute__((unused)) XN297_SetTXAddr(const uint8_t*, uint8_t);
 static void __attribute__((unused)) XN297_SetRXAddr(const uint8_t*, uint8_t);
 static void __attribute__((unused)) XN297_SetTxRxMode(enum TXRX_State);
 static void __attribute__((unused)) XN297_SendPayload(uint8_t*, uint8_t);
+static void __attribute__((unused)) XN297_ReSendPayload();
 static void __attribute__((unused)) XN297_WritePayload(uint8_t*, uint8_t);
 static void __attribute__((unused)) XN297_WriteEnhancedPayload(uint8_t*, uint8_t, uint8_t);
 static bool __attribute__((unused)) XN297_IsRX();

Protocols_Details.md

@@ -99,7 +99,7 @@ CFlie|38|CFlie||||||||NRF24L01|
 [FrskyX2](Protocols_Details.md#FRSKYX2---64)|64|CH_16|CH_8|EU_16|EU_8|Cloned|Cloned_8|||CC2500|
 [Frsky_RX](Protocols_Details.md#FRSKY_RX---55)|55|Multi|CloneTX|EraseTX|CPPM|||||CC2500|
 [Futaba/SFHSS](Protocols_Details.md#Futaba---21)|21|SFHSS||||||||CC2500|
-[FX](Protocols_Details.md#FX---58)|28|816|620|9630|Q560|||||NRF24L01|
+[FX](Protocols_Details.md#FX---58)|28|816|620|9630|Q560|QF012||||NRF24L01|
 [FY326](Protocols_Details.md#FY326---20)|20|FY326|FY319|||||||NRF24L01|
 [GD00X](Protocols_Details.md#GD00X---47)|47|GD_V1*|GD_V2*|||||||NRF24L01|XN297L
 [GW008](Protocols_Details.md#GW008---32)|32|||||||||NRF24L01|XN297
@@ -115,6 +115,7 @@ CFlie|38|CFlie||||||||NRF24L01|
 [JIABAILE](Protocols_Details.md#JIABAILE---102)|102|Std|Gyro|||||||NRF24L01|XN297
 [JJRC345](Protocols_Details.md#JJRC345---71)|71|JJRC345|SkyTmblr|||||||NRF24L01|XN297
 [JOYSWAY](Protocols_Details.md#JOYSWAY---84)|84|||||||||NRF24L01|XN297
+[KAMTOM](Protocols_Details.md#KAMTOM---104)|104|||||||||NRF24L01|XN297
 [KF606](Protocols_Details.md#KF606---49)|49|KF606|MIG320|ZCZ50||||||NRF24L01|XN297
 [KN](Protocols_Details.md#KN---9)|9|WLTOYS|FEILUN|||||||NRF24L01|
 [Kyosho](Protocols_Details.md#Kyosho---73)|73|FHSS|Hype|||||||A7105|
@@ -143,6 +144,7 @@ CFlie|38|CFlie||||||||NRF24L01|
 [Scorpio](Protocols_Details.md#Scorpio---94)|94|||||||||CYRF6936|
 [SGF22](Protocols_Details.md#SGF22---97)|97|F22|F22S|J20||||||NRF24L01|XN297
 [Shenqi](Protocols_Details.md#Shenqi---19)|19|Shenqi||||||||NRF24L01|LT8900
+[Shenqi2](Protocols_Details.md#Shenqi2---105)|105|Shenqi2||||||||NRF24L01|XN297
 [Skyartec](Protocols_Details.md#Skyartec---68)|68|||||||||CC2500|CC2500
 [SLT](Protocols_Details.md#SLT---11)|11|SLT_V1|SLT_V2|Q100|Q200|MR100|V1_4CH|RF_SIM||NRF24L01|CC2500
 [SymaX](Protocols_Details.md#Symax---10)|10|SYMAX|SYMAX5C|||||||NRF24L01|
@@ -153,6 +155,7 @@ CFlie|38|CFlie||||||||NRF24L01|
 [WFLY](Protocols_Details.md#WFLY---40)|40|WFR0x||||||||CYRF6936|
 [WFLY2](Protocols_Details.md#WFLY2---79)|79|RF20x||||||||A7105|
 [WK2x01](Protocols_Details.md#WK2X01---30)|30|WK2801|WK2401|W6_5_1|W6_6_1|W6_HEL|W6_HEL_I|||CYRF6936|
+[WL91X](Protocols_Details.md#WL91X---106)|106|||||||||NRF24L011&CC2500|XN297
 [XERALL](Protocols_Details.md#XERALL---91)|91|Tank||||||||NRF24L01|XN297
 [XK](Protocols_Details.md#XK---62)|62|X450|X420|Cars||||||NRF24L011&CC2500|XN297
 [XK2](Protocols_Details.md#XK2---99)|99|X4|P10|||||||NRF24L01&CC2500|XN297
@@ -1439,11 +1442,14 @@ FLIP: sets model into flip mode for approx 5 seconds at each throw of switch (re
 MODE: -100% level, +100% acro
 
 ### Sub_protocol V1_4CH - *5*
+Transmitters: SLT2 and SLT2 DLC, Receivers: SPMXSE2825RX, SPMXSBER1025G, SPMXSE4510RX, ...
 
 CH1|CH2|CH3|CH4
 ---|---|---|---
 CH1|CH2|CH3|CH4
 
+CH4 is used for DSC settings: -35% off to +15% full
+
 ### Sub_protocol RF_SIM - *6*
 Models: the SLT-dongle included in RealFlight 7.5
 
@@ -1481,6 +1487,14 @@ A|E|T|R|CALIB|RATE|6G_3D|6GSENIOR|LIGHT
 
 A280 -> 6GSENIOR: -100% - 6G, +100% - Senior mode (turn off gyro), LIGHT: cycle the light through on-flash-off when the CH9 value is changed from -100% to 100%
 
+## WL91X - *106*
+
+Models: WLtoys WL911, WL913, WL915 and may be others...
+
+CH1|CH2|CH3|CH4
+---|---|---|---
+ST|TH|ST_TR|TH_TR
+
 ## XK - *62*
 
 CC2500: only X450 is supported.
@@ -1532,6 +1546,8 @@ The plane does not need to be bound each time if it is powered on **after** the
 
 The rudder trim is driven from the rudder channel to increase the range (Original TX rudder has no range once the motor has been turned on...).
 
+Mode: -100%=6G, 0%=3D, +100%=Gyro off (Senior mode)
+
 ### Sub_protocol X4 - *0*
 Transmitter: XK X4-A160, X5S, model: XK A160S, XK A280, XK A300
 
@@ -1785,18 +1801,22 @@ FMODE and AUX7 have 4 positions: -100%..-50%=>0, -50%..5%=>1, 5%..50%=>2, 50%..1
 ## FX - *58*
 FEI XIONG
 
-CH1|CH2|CH3|CH4
----|---|---|---
-A|-|T|-
-
 ### Sub_protocol 816 - *0*
 Model: FX816 P38, B17
 
 Only 8 TX IDs available
 
+CH1|CH2|CH3|CH4
+---|---|---|---
+A|-|T|-
+
 ### Sub_protocol 620 - *1*
 Model: FX620 SU35
 
+CH1|CH2|CH3|CH4
+---|---|---|---
+A|-|T|-
+
 ### Sub_protocol 9630 - *2*
 Model: FX9630, FX9603, QIDI-550
 
@@ -1819,6 +1839,19 @@ FLIP is a toggle channel meaning that -100% to +100% is a command and +100% to -
 
 Gyro: -100%=6G, 0%=3D+Gyro, +100%=3D
 
+### Sub_protocol QF012 - *4*
+Model: QF012 SBD Dauntless
+
+CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8
+---|---|---|---|---|---|---|---
+A|E|T|R|FLIP|GYRO|Invert|Reset
+
+FLIP is a toggle channel meaning that -100% to +100% is a command and +100% to -100% is also a command
+
+Gyro: -100%=6G, 0%=3D+Gyro, +100%=3D
+
+Reset: Restore fine tunning midpoint
+
 ## FY326 - *20*
 
 ### Sub_protocol FY326 - *0*
@@ -1981,6 +2014,15 @@ Model: DF-Models SkyTumbler
 
 RTH not supported
 
+## KAMTOM - *104*
+Models: KAMTOM RC Racing KM24xx (KM32xx?), Pinecone SG-24xx
+
+CH1|CH2|CH3|CH4|CH5|CH6|CH7
+---|---|---|---|---|---|---
+ST|TH|UNK1|UNK2|ST_TR|TH_TR|TH_DR
+
+Low battery telemetry in A1 with 0 = low batt
+
 ## KYOSHO2 - *93*
 Model: TX KT-17, Minium Edge 540, Minium Citabria
 
@@ -2151,6 +2193,15 @@ CH1|CH2|CH3|CH4
 
 Throttle +100%=full forward,0%=stop,-100%=full backward.
 
+## Shenqi2 - *105*
+Autobind protocol
+
+Model: Shenqiwei 1/20 Mini Motorcycle
+
+CH1|CH2
+---|---
+ST|TH
+
 ## Symax - *10*
 Autobind protocol
 

docs/Compiling.md

@@ -108,7 +108,7 @@ The images below indicate the pin layout and the location of the ground pin on t
 |:---:|:---:|:---:|
 <img src="images/V2b_ISP.jpeg" width="189" height="200" /> | <img src="images/MPTM_PCB_2.3d_ISP.png" width="486" height="201" /> | <img src="images/ProMini_ISP.png" width="195" height="200" /> |
 
-You are now ready to plug in the USB programmer to the computer.  If you are looking for a good working USBasp Windows driver, [use this one](http://www.protostack.com/download/USBasp-win-driver-x86-x64-v3.0.7.zip).
+You are now ready to plug in the USB programmer to the computer.  If you are looking for a good working USBasp Windows driver, [use this one](https://protostack.com.au/download/USBasp-win-driver-x86-x64-v3.0.7.zip).
 
 ### Burn bootloader and set fuses
 The bootloader only needs to be burned once, unless you decide to switch from one option to the other (or it is accidentally erased).  If you have already burned the bootloader / set the fuses you can skip this step.