Remove Kyosho/FHSS&SYNC when MULTI_AIR

Save flash space

.github/workflows/main.yml

@@ -39,16 +39,26 @@ jobs:
     strategy:
       fail-fast: false
       matrix:
-        board: [
-          "multi4in1:avr:multiatmega328p:bootloader=none", 
-          "multi4in1:avr:multiatmega328p:bootloader=optiboot", 
-          "multi4in1:avr:multixmega32d4", 
-          "multi4in1:STM32F1:multi5in1t18int", 
-          "multi4in1:STM32F1:multistm32f103cb:debug_option=none", 
-          "multi4in1:STM32F1:multistm32f103cb:debug_option=native", 
-          "multi4in1:STM32F1:multistm32f103cb:debug_option=ftdi", 
-          "multi4in1:STM32F1:multistm32f103c8:debug_option=none"
-        ]
+        include:
+          - board: "multi4in1:avr:multiatmega328p:bootloader=none"
+            name: "ATmega328p"
+          - board: "multi4in1:avr:multiatmega328p:bootloader=optiboot"
+            name: "ATmega328p (Optiboot)"
+          - board: "multi4in1:avr:multixmega32d4"
+            name: "OrangeRX"
+          - board: "multi4in1:STM32F1:multistm32f103c8:debug_option=none"
+            name: "STM32F103 (64KB)"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=none"
+            name: "STM32F103 (128KB)"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=native"
+            name: "STM32F103 (128KB, USB Debugging)"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=ftdi"
+            name: "STM32F103 (128KB, Serial Debugging)"
+          - board: "multi4in1:STM32F1:multi5in1t18int"
+            name: "T18 5-in-1 (128KB)"
+
+    # Set the build name using the friendly board name
+    name: ${{ matrix.name }}
 
     # Set the environment variables
     env:

Lua_scripts/DSM FwdPrg_56_Color.lua

@@ -1,5 +1,5 @@
-local toolName = "TNS|DSM Forward Prog v0.55a (Color) |TNE"
-local VERSION  = "v0.55a"
+local toolName = "TNS|DSM Forward Prog v0.56 (Color) |TNE"
+local VERSION  = "v0.56"
 
 ---- #########################################################################
 ---- #                                                                       #

Lua_scripts/DSM FwdPrg_56_STUP.lua

@@ -0,0 +1,951 @@
+local toolName = "TNS|DSM Frwd Prog v0.56a (MIN-SETUP)|TNE"
+
+---- #########################################################################
+---- #                                                                       #
+---- # Copyright (C) OpenTX                                                  #
+-----#                                                                       #
+---- # License GPLv2: http://www.gnu.org/licenses/gpl-2.0.html               #
+---- #                                                                       #
+---- # This program is free software; you can redistribute it and/or modify  #
+---- # it under the terms of the GNU General Public License version 2 as     #
+---- # published by the Free Software Foundation.                            #
+---- #                                                                       #
+---- # This program is distributed in the hope that it will be useful        #
+---- # but WITHOUT ANY WARRANTY; without even the implied warranty of        #
+---- # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the         #
+---- # GNU General Public License for more details.                          #
+---- #                                                                       #
+---- #########################################################################
+
+
+local VERSION             = "v0.56"
+local DSMLIB_PATH         = "/SCRIPTS/TOOLS/DSMLIB/"
+local DATA_PATH           = "/MODELS/DSMDATA"
+
+local LOG_FILE            = "/LOGS/dsm_min_log.txt"
+
+-- Phase
+local PH_INIT = 0
+local PH_RX_VER, PH_TITLE  = 1, 2
+local PH_VAL_CHANGING, PH_VAL_EDITING, PH_VAL_EDIT_END     = 6, 7, 8
+local PH_WAIT_CMD, PH_EXIT_REQ, PH_EXIT_DONE               = 9, 10, 11
+
+-- Line Types
+local LT_MENU, LT_LIST_NC = 0x1C, 0x6C
+
+local Phase               = PH_INIT
+
+local Text                = {}
+local List_Text           = {}
+local List_Text_Img       = {}
+
+local originalValue       = 0
+
+local  ctx_SelLine = 0      -- Current Selected Line
+local  ctx_EditLine = nil   -- Current Editing Line
+
+local Menu                = { MenuId = 0, Text = "", TextId = 0, PrevId = 0, NextId = 0, BackId = 0 }
+local MenuLines           = {}
+
+local logFile             = nil
+
+local LCD_W_BUTTONS       = 19
+local LCD_H_BUTTONS       = 10
+
+local LCD_X_MAX           = 128
+local LCD_X_RIGHT_BUTTONS = LCD_X_MAX - LCD_W_BUTTONS - 1
+
+local LCD_Y_LINE_HEIGHT   = 7
+local LCD_Y_LOWER_BUTTONS = (8 * LCD_Y_LINE_HEIGHT) + 2
+
+local TEXT_ATTR           = SMLSIZE
+
+local TX_CHANNELS         = 12
+
+local AT_PLANE   = 0
+
+local aircraft_type_text = {[0]="Plane","Heli","Glider","Drone"}
+
+local WT_A1       = 0
+local WT_A2       = 1
+local WT_FLPR     = 2
+local WT_A1_F1    = 3
+local WT_A2_F1    = 4
+local WT_A2_F2    = 5
+local WT_ELEVON_A = 6
+local WT_ELEVON_B = 7
+
+local wing_type_text = {[0]="Normal","Dual Ail","Flapperon", "Ail + Flp","Dual Ail + Flp","Dual Ail/Flp","Elevon A","Elevon B"}
+
+local TT_R1    = 0
+local TT_R1_E1 = 1
+local TT_R1_E2 = 2
+local TT_R2_E1 = 3
+local TT_R2_E2 = 4
+local TT_VT_A  = 5
+local TT_VT_B  = 6
+local TT_TLRN_A = 7
+local TT_TLRN_B = 8
+local TT_TLRN_A_R2 = 9
+local TT_TLRN_B_R2 = 10
+
+local tail_type_text = {[0]="Rud Only","Normal","Rud + Dual Ele","Dual Rud + Elv","Dual Rud/Ele",
+                         "VTail A","VTail B","Taileron A","Taileron B", 
+                         "Taileron A + Dual Rud","Taileron B + Dual Rud"
+                        }
+
+local MT_NORMAL      = 0
+local MT_REVERSE     = 1
+
+local P1 = 0
+local P2 = 1
+local P3 = 2
+local P4 = 3
+local P5 = 4
+local P6 = 5
+local P7 = 6
+local P8 = 7
+--local P9 = 8
+--local P10 = 9
+
+local MV_AIRCRAFT_TYPE = 1001
+local MV_WING_TYPE     = 1002
+local MV_TAIL_TYPE     = 1003
+        
+local MV_CH_BASE       = 1010
+local MV_CH_THR        = 1010
+
+local MV_CH_L_AIL      = 1011
+local MV_CH_R_AIL      = 1012
+local MV_CH_L_FLP      = 1013
+local MV_CH_R_FLP      = 1014
+
+local MV_CH_L_RUD      = 1015
+local MV_CH_R_RUD      = 1016
+local MV_CH_L_ELE      = 1017
+local MV_CH_R_ELE      = 1018
+
+local MV_PORT_BASE       = 1020
+local MV_P1_MODE      = 1020
+--local MV_P2_MODE      = 1021
+--local MV_P3_MODE      = 1022
+--local MV_P4_MODE      = 1023
+--local MV_P5_MODE      = 1024
+local MV_P6_MODE      = 1025
+--local MV_P7_MODE      = 1026
+--local MV_P8_MODE      = 1027
+--local MV_P9_MODE      = 1028
+--local MV_P10_MODE     = 1029
+
+local MV_DATA_END        = 1040
+
+-- MENU DATA Management
+local M_DB = {}            -- Store the variables used in the Menus.
+
+local lastGoodMenu=0      
+  
+local currATyp = -1    
+local currTTyp = -1
+local currWTyp = -1
+
+local menuDataChanged = false
+
+local MODEL = {
+  modelName = "",            -- The name of the model comming from OTX/ETX
+  hashName = nil,
+  modelOutputChannel = {},   -- Output information from OTX/ETX
+
+  TX_CH_TEXT= { }, 
+  PORT_TEXT = { },
+
+  DSM_ChannelInfo = {}       -- Data Created by DSM Configuration Script
+}
+
+local function gc()
+  collectgarbage("collect")
+end
+
+--[[
+local function gcTable(t)
+  if type(t)=="table" then
+    for i,v in pairs(t) do
+      if type(v) == "table" then
+        gcTable(v)
+      end
+      t[i] = nil
+    end
+  end
+  gc()
+  return t 
+end
+--]]
+
+local function LOG_open()
+  logFile = io.open(LOG_FILE, "w")   -- Truncate Log File
+end
+
+local function LOG_write(...)
+  if (logFile == nil) then LOG_open() end
+  local str = string.format(...)
+  io.write(logFile, str)
+end
+
+local function LOG_close()
+  if (logFile ~= nil) then io.close(logFile) end
+end
+
+-- Saves MENU_DATA to a file
+local function ST_SaveFileData() 
+  local fname = MODEL.hashName
+
+  print("Saving File:"..fname)
+  local dataFile = assert(io.open(DATA_PATH .. "/" .. fname, "w"),"Please create "..DATA_PATH.." folder")  -- write File 
+  
+  -- Foreach MENU_DATA with a value write Var_Id:Value into file
+  for i = 0, MV_DATA_END do
+      if (M_DB[i]~=nil) then
+          io.write(dataFile,string.format("%s:%s\n",i,M_DB[i]))
+      end
+  end
+  io.close(dataFile)
+end
+
+local function tailTypeCompatible(a,b)
+
+  local function normalize(tt)
+    if (tt==TT_TLRN_A or tt==TT_TLRN_B) then 
+      return TT_TLRN_A
+    elseif (tt==TT_TLRN_A_R2 or tt==TT_TLRN_B_R2) then
+      return TT_TLRN_A_R2
+    elseif (tt==TT_VT_A or tt==TT_VT_B) then
+      return TT_VT_A
+    else
+      return tt
+    end
+  end
+
+  return (normalize(a)==normalize(b))
+end
+
+local function ST_PlaneWingInit(wingType) 
+    --print("Change Plane WingType:"..wing_type_text[wingType])
+
+    M_DB[MV_WING_TYPE] = wingType
+
+    -- Clear all Wing Data 
+    M_DB[MV_CH_L_AIL] = nil
+    M_DB[MV_CH_R_AIL] = nil
+    M_DB[MV_CH_L_FLP] = nil
+    M_DB[MV_CH_R_FLP] = nil
+
+    M_DB[MV_CH_THR] = P1
+    
+    -- Default Channel Assisgments for each Wing type
+
+    if (wingType==WT_A1) then
+        M_DB[MV_CH_L_AIL] = P2
+    elseif (wingType==WT_A2 or wingType==WT_FLPR) then
+        M_DB[MV_CH_L_AIL] = P6
+        M_DB[MV_CH_R_AIL] = P2
+    elseif (wingType==WT_A1_F1) then
+        M_DB[MV_CH_L_AIL] = P2
+        M_DB[MV_CH_L_FLP] = P6
+    elseif (wingType==WT_A2_F1) then
+        M_DB[MV_CH_L_AIL] = P6
+        M_DB[MV_CH_R_AIL] = P2
+        M_DB[MV_CH_L_FLP] = P5
+    elseif (wingType==WT_A2_F2) then
+        M_DB[MV_CH_L_AIL] = P6
+        M_DB[MV_CH_R_AIL] = P2
+        M_DB[MV_CH_R_FLP] = P5
+        M_DB[MV_CH_L_FLP] = P7
+    elseif (wingType==WT_ELEVON_A) then
+        M_DB[MV_CH_L_AIL] = P2
+        M_DB[MV_CH_R_AIL] = P3
+    elseif (wingType==WT_ELEVON_B) then
+        M_DB[MV_CH_L_AIL] = P3
+        M_DB[MV_CH_R_AIL] = P2
+    else -- Assume normal 
+       print("ERROR: Invalid Wing Type")
+    end 
+end
+
+local function ST_PlaneTailInit(tailType) 
+    if (M_DB[MV_WING_TYPE]==WT_ELEVON_A or
+        M_DB[MV_WING_TYPE]==WT_ELEVON_B) then
+        tailType = TT_R1 -- Delta only have ruder  
+    end
+
+    --print("Change Plane Tail Type:"..tail_type_text[tailType])
+
+    -- Clear all data for Tail 
+    M_DB[MV_TAIL_TYPE] = tailType
+    M_DB[MV_CH_L_ELE] = nil
+    M_DB[MV_CH_R_ELE] = nil
+    M_DB[MV_CH_L_RUD] = nil
+    M_DB[MV_CH_R_RUD] = nil
+
+    -- Setup Channels for different Tail types 
+    if (tailType == TT_R1) then
+        M_DB[MV_CH_L_RUD] = P4
+    elseif (tailType == TT_R1_E1) then
+        M_DB[MV_CH_L_ELE] = P3
+        M_DB[MV_CH_L_RUD] = P4
+    elseif (tailType == TT_R1_E2) then
+        M_DB[MV_CH_L_ELE] = P5
+        M_DB[MV_CH_R_ELE] = P3
+        M_DB[MV_CH_L_RUD] = P4
+    elseif (tailType == TT_R2_E1) then
+        M_DB[MV_CH_L_ELE] = P3
+        M_DB[MV_CH_L_RUD] = P4
+        M_DB[MV_CH_R_RUD] = P5
+    elseif (tailType == TT_R2_E2) then
+        M_DB[MV_CH_L_ELE] = P5
+        M_DB[MV_CH_R_ELE] = P3
+        M_DB[MV_CH_L_RUD] = P4
+        M_DB[MV_CH_R_RUD] = P6
+    elseif (tailType == TT_VT_A or tailType == TT_VT_B) then
+        M_DB[MV_CH_L_ELE] = P3
+        M_DB[MV_CH_R_ELE] = P4
+    elseif (tailType == TT_TLRN_A or tailType == TT_TLRN_B or
+            tailType == TT_TLRN_A_R2 or tailType == TT_TLRN_B_R2) then
+        M_DB[MV_CH_L_RUD] = P4
+        M_DB[MV_CH_L_ELE] = P5
+        M_DB[MV_CH_R_ELE] = P3
+    else -- Assume Normal 
+        print("ERROR:invalid Tail Type")
+    end
+
+    if (tailType == TT_TLRN_A_R2 or tailType == TT_TLRN_B_R2) then
+      M_DB[MV_CH_R_RUD] = P8
+    end
+end
+
+local function ST_AircraftInit(aircraftType)
+    M_DB[MV_AIRCRAFT_TYPE] = aircraftType
+    ST_PlaneWingInit(WT_A1)
+    ST_PlaneTailInit(TT_R1_E1)
+end
+
+
+-- Setup Initial Default Data for the Menus
+local function ST_Default_Data()
+    ST_AircraftInit(AT_PLANE)
+
+    for i=0,9 do
+      M_DB[MV_P1_MODE+i] = MT_NORMAL + MODEL.modelOutputChannel[P1+i].revert
+    end
+end
+
+local function MenuLinePostProcessing(line)
+    line.MenuId = Menu.MenuId
+
+    if line.Type == LT_MENU then
+        -- nothing to do on menu entries
+        line.Val=nil
+    elseif line.Type == LT_LIST_NC then
+        -- Normalize Min/Max to be relative to Zero
+        line.TextStart = line.Min
+        line.Def = line.Def - line.Min -- normalize default value 
+        line.Max = line.Max - line.Min -- normalize max index
+        line.Min = 0 -- min index
+    end
+end
+
+
+local function portUse(p)
+  local out = nil 
+  if p==M_DB[MV_CH_THR] then out = "Thr"
+  elseif p == M_DB[MV_CH_L_AIL] then 
+      out=(M_DB[MV_CH_R_AIL] and "Ail_L") or "Ail"
+  elseif p == M_DB[MV_CH_R_AIL] then out="Ail_R"
+  elseif p == M_DB[MV_CH_L_ELE] then 
+      out=(M_DB[MV_CH_R_ELE] and "Ele_L") or "Ele"
+  elseif p == M_DB[MV_CH_R_ELE] then out="Ele_R"
+  elseif p == M_DB[MV_CH_L_RUD] then 
+      out=(M_DB[MV_CH_R_RUD] and "Rud_L") or "Rud"
+  elseif p == M_DB[MV_CH_R_RUD] then out="Rud-R"
+  elseif p == M_DB[MV_CH_L_FLP] then 
+      out=(M_DB[MV_CH_R_FLP] and "Flp_L") or "Flp"
+  elseif p == M_DB[MV_CH_R_FLP] then out="Flp_R"
+  else
+    out = ""
+  end
+  return out
+end
+
+-- Creates the menus to Render with the GUI
+local function ST_LoadMenu(menuId)
+
+    local function Header(p)
+      return MODEL.PORT_TEXT[p].." "..portUse(p)
+    end
+
+    local function generateGyroReverse(menuId, P_BASE, V_BASE)
+      for i=0,4 do
+        MenuLines[i] = { Type = LT_LIST_NC, Text=Header(P_BASE+i), TextId = 0, ValId = V_BASE+i, Min=45, Max=46, Def=45, Val=M_DB[V_BASE+i] }
+      end
+
+      MenuLines[5] = { Type = LT_MENU, Text="Only TAER affects AS3X/SAFE react dir", TextId = 0, ValId = menuId }
+      MenuLines[6] = { Type = LT_MENU, Text="If changes, RX 'Relearn Servo'", TextId = 0, ValId = menuId }
+
+      ctx_SelLine = 0
+    end
+
+    -- Begin
+    for i = 0, 6 do -- clear menu
+        MenuLines[i] = { MenuId = 0, lineNum = 0, Type = 0 }
+    end
+
+    
+    if (menuId==0x1000) then -- MAIN MENU
+        Menu = { MenuId = 0x1000, Text = "Save-Exit ("..MODEL.modelName..")", PrevId = 0, NextId = 0, BackId = 0, TextId=0 }
+       
+        if (true) then
+            MenuLines[4] = { Type = LT_MENU, Text="Save Changes", TextId = 0, ValId = 0x1005 }
+            MenuLines[5] = { Type = LT_MENU, Text="Discard Changes", TextId = 0, ValId = 0xFFF9 }
+            ctx_SelLine = 4 
+        end
+        lastGoodMenu = menuId
+    elseif (menuId==0x1001) then -- MODEL SETUP
+        local backId = 0xFFF9 -- No changes, just exit
+        local title  =  "Setup  ("..MODEL.modelName..")"
+        if (menuDataChanged) then
+            backId = 0x1000  -- Go to Save menu
+            title = title.." *"
+        end
+        Menu = { MenuId = 0x1001, Text = title, PrevId = 0, NextId = 0, BackId = backId, TextId=0 }
+        MenuLines[0] = { Type = LT_MENU, Text = "Aircraft Setup", ValId = 0x1010,TextId=0 }
+        MenuLines[1] = { Type = LT_MENU, Text = "Wing & Tail Channels ", ValId = 0x1020, TextId=0 } 
+        MenuLines[3] = { Type = LT_MENU, Text = "Gyro Channel Reverse", ValId = 0x1030, TextId=0 } 
+        MenuLines[5] = { Type = LT_MENU, Text = "WARNING: Changing of Aircraft", ValId = 0x1001, TextId=0 } 
+        MenuLines[6] = { Type = LT_MENU, Text = "deletes prev Ch/Port assgmt.", ValId = 0x1001, TextId=0 } 
+
+        ctx_SelLine = 0
+        lastGoodMenu = menuId
+    elseif (menuId==0x1005) then
+        ST_SaveFileData()
+        menuDataChanged = false
+
+        local msg1 = "Data saved to: " 
+        local msg2 = " ../DSMLIB/"..MODEL.hashName
+
+        Menu = { MenuId = 0x1005, Text = "Config Saved", PrevId = 0, NextId = 0, BackId = 0, TextId=0 }
+        MenuLines[2] = { Type = LT_MENU, Text=msg1, TextId = 0, ValId = 0x1005 }
+        MenuLines[3] = { Type = LT_MENU, Text=msg2, TextId = 0, ValId = 0x1005 }
+        MenuLines[6] = { Type = LT_MENU, Text="Complete", TextId = 0, ValId = 0xFFF9 }
+        ctx_SelLine = 6
+        lastGoodMenu = menuId
+    elseif (menuId==0x1010) then
+        Menu = { MenuId = 0x1010, Text = "Aircraft", PrevId = 0, NextId = 0x1011, BackId = 0x1001, TextId=0 }
+        MenuLines[5] = { Type = LT_LIST_NC, Text="Aircraft Type", TextId = 0, ValId = MV_AIRCRAFT_TYPE, Min=15, Max=15, Def=15, Val=M_DB[MV_AIRCRAFT_TYPE] }
+        ctx_SelLine = 5
+        lastGoodMenu = menuId
+    elseif (menuId==0x1011) then
+        Menu = { MenuId = 0x1011, Text = "Model Type: "..aircraft_type_text[currATyp], PrevId = 0, NextId = 0x1020, BackId = 0x1010, TextId=0 }
+        MenuLines[5] = { Type = LT_LIST_NC, Text="Wing Type", TextId = 0, ValId = MV_WING_TYPE, Min=20, Max=27, Def=20, Val=M_DB[MV_WING_TYPE] }
+        MenuLines[6] = { Type = LT_LIST_NC, Text="Tail Type", TextId = 0, ValId = MV_TAIL_TYPE, Min=30, Max=40, Def=30, Val=M_DB[MV_TAIL_TYPE] }
+        ctx_SelLine = 5
+        lastGoodMenu = menuId
+    elseif (menuId==0x1020) then
+        ------ WING  SETUP -------
+        local thr = M_DB[MV_CH_THR]
+        local leftAil = M_DB[MV_CH_L_AIL]
+        local rightAil = M_DB[MV_CH_R_AIL]
+        local leftFlap = M_DB[MV_CH_L_FLP]
+        local rightFlap = M_DB[MV_CH_R_FLP]
+
+        local thrText     = "Thr"
+        local leftAilText = "Left Ail"
+        local rightAilText = "Right Ail"
+        local leftFlapText = "Left Flap"
+        local rightFlapText = "Right Flap"
+
+        if (rightAil==nil) then leftAilText = "Aileron" end
+        if (rightFlap==nil) then leftFlapText = "Flap" end
+
+        local title = aircraft_type_text[currATyp].."   Wing:"..wing_type_text[currWTyp]
+
+        Menu = { MenuId = 0x1020, Text = title, PrevId = 0, NextId = 0x1021, BackId = 0x1011, TextId=0 }
+
+        MenuLines[0] = { Type = LT_LIST_NC, Text=thrText, TextId = 0, ValId = MV_CH_THR, Min=0, Max=10, Def=0, Val= thr }
+
+        MenuLines[2] = { Type = LT_LIST_NC, Text=leftAilText, TextId = 0, ValId = MV_CH_L_AIL, Min=0, Max=9, Def=0, Val= leftAil }
+
+        if (rightAil) then
+            MenuLines[3] = { Type = LT_LIST_NC, Text=rightAilText, TextId = 0, ValId = MV_CH_R_AIL, Min=0, Max=9, Def=0, Val= rightAil }
+        end
+
+        if (leftFlap) then
+            MenuLines[4] = { Type = LT_LIST_NC, Text=leftFlapText, TextId = 0, ValId = MV_CH_L_FLP, Min=0, Max=9, Def=0, Val= leftFlap }
+        end
+        if (rightFlap) then
+            MenuLines[5] = { Type = LT_LIST_NC, Text=rightFlapText, TextId = 0, ValId = MV_CH_R_FLP, Min=0, Max=9, Def=0, Val= rightFlap }
+        end
+
+        ctx_SelLine = 0
+        lastGoodMenu = menuId
+
+    elseif (menuId==0x1021) then
+        ------ TAIL SETUP -------
+        local leftRud = M_DB[MV_CH_L_RUD] 
+        local rightRud = M_DB[MV_CH_R_RUD] 
+        local leftEle = M_DB[MV_CH_L_ELE]
+        local rightEle = M_DB[MV_CH_R_ELE]
+
+        local leftRudText = "Left Rud"
+        local rightRudText = "Right Rud"
+
+        local leftElvText = "Left Ele"
+        local rightElvText = "Right Ele"
+
+        if (rightRud==nil) then leftRudText = "Rud"  end
+        if (rightEle==nil) then leftElvText = "Ele" end
+
+        local title = aircraft_type_text[currATyp].."  Tail:"..tail_type_text[currTTyp]
+
+        Menu = { MenuId = 0x1021, Text = title, PrevId = 0, NextId = 0x1001, BackId = 0x1020, TextId=0 }
+        if (leftRud) then
+            MenuLines[1] = { Type = LT_LIST_NC, Text=leftRudText, TextId = 0, ValId = MV_CH_L_RUD, Min=0, Max=9, Def=0, Val= leftRud}
+        end
+
+        if (rightRud) then
+            MenuLines[2] = { Type = LT_LIST_NC, Text=rightRudText, TextId = 0, ValId = MV_CH_R_RUD, Min=0, Max=9, Def=0, Val=rightRud }
+        end
+
+        if (leftEle) then
+            MenuLines[4] = { Type = LT_LIST_NC, Text=leftElvText, TextId = 0, ValId = MV_CH_L_ELE, Min=0, Max=9, Def=0, Val=leftEle }
+        end
+
+        if (rightEle) then
+            MenuLines[5] = { Type = LT_LIST_NC, Text=rightElvText, TextId = 0, ValId = MV_CH_R_ELE, Min=0, Max=9, Def=0, Val=rightEle }
+        end
+
+        ctx_SelLine = 1
+        lastGoodMenu = menuId
+   
+    elseif (menuId==0x1030) then
+        Menu = { MenuId = 0x1030, Text = "Gyro Reverse (Port 1-5)", PrevId = 0, NextId = 0x1031, BackId = 0x1001, TextId=0 }
+        generateGyroReverse(menuId,P1,MV_P1_MODE)
+        lastGoodMenu = menuId
+    elseif (menuId==0x1031) then
+        Menu = { MenuId = 0x1031, Text = "Gyro Reverse (Port 6-10)", PrevId = 0x1030, NextId = 0, BackId = 0x1001, TextId=0 }
+        generateGyroReverse(menuId,P6,MV_P6_MODE)
+        lastGoodMenu = menuId
+    elseif (menuId==0xFFF9) then
+        ChangePhase(PH_EXIT_DONE)
+        return
+    else
+        Menu = { MenuId = 0x0002, Text = "NOT IMPLEMENTED", TextId = 0, PrevId = 0, NextId = 0, BackId = lastGoodMenu }
+        ctx_SelLine = -1 -- BACK BUTTON
+    end
+
+    for i = 0, 6 do 
+        if (MenuLines[i].Type > 0) then
+            MenuLinePostProcessing(MenuLines[i])
+        end
+    end
+    gc()
+end
+
+-- Inital List and Image Text for this menus
+local function ST_Init_Text(rxId) 
+    -- Channel Names use the Port Text Retrived from OTX/ETX
+    local p = 0
+
+    for i = 0, 9 do List_Text[i] = MODEL.PORT_TEXT[i]  end
+    List_Text[10] = "--"
+
+    -- Aircraft Type
+    List_Text[15+AT_PLANE]  = "Airplane"; 
+
+    -- Wing Types
+    p = 20+WT_A1;    List_Text[p] = "Single Ail";  --List_Text_Img[p]  = "x.png|Single Aileron" 
+    p = 20+WT_A2;    List_Text[p] = "Dual Ail";  --List_Text_Img[p]  = "x.png|Dual Aileron" 
+    p = 20+WT_FLPR;  List_Text[p] = "Flaperon";  --List_Text_Img[p]  = "x.png|Flaperon" 
+    p = 20+WT_A1_F1; List_Text[p] = "Ail + Flap";  --List_Text_Img[p]  = "x.png|Aileron + Flap" 
+    p = 20+WT_A2_F1; List_Text[p] = "Dual Ail + Flap";  --List_Text_Img[p]  = "x.png|Dual Aileron + Flap" 
+    p = 20+WT_A2_F2; List_Text[p] = "Dual Ail + Dual Flap";  --List_Text_Img[p]  = "x.png|Dual Aileron + Dual Flap" 
+    p = 20+WT_ELEVON_A; List_Text[p] = "Delta A";  --List_Text_Img[p]  = "x.png|Delta/Elevon A" 
+    p = 20+WT_ELEVON_B; List_Text[p] = "Delta B";  --List_Text_Img[p]  = "x.png|Delta/Elevon B" 
+
+    -- Tail Types
+    p = 30+TT_R1;    List_Text[p] = "Rudder Only";  --List_Text_Img[p]  = "x.png|Rudder Only" 
+    p = 30+TT_R1_E1; List_Text[p] = "Rud + Ele";  --List_Text_Img[p]  = "x.png|Tail Normal" 
+    p = 30+TT_R1_E2; List_Text[p] = "Rud + Dual Ele";  --List_Text_Img[p]  = "x.png|Rud + Dual Ele" 
+    p = 30+TT_R2_E1; List_Text[p] = "Dual Rud + Ele";  --List_Text_Img[p]  = "x.png|Dual Rud + Ele" 
+    p = 30+TT_R2_E2; List_Text[p] = "Dual Rud + Dual Ele";  --List_Text_Img[p]  = "x.png|Dual Rud + Dual Elev" 
+    p = 30+TT_VT_A;  List_Text[p] = "V-Tail A";  --List_Text_Img[p]  = "x.png|V-Tail A" 
+    p = 30+TT_VT_B;  List_Text[p] = "V-Tail B";  --List_Text_Img[p]  = "x.png|V-Tail B" 
+    p = 30+TT_TLRN_A; List_Text[p] = "Taileron A";  --List_Text_Img[p]  = "x.png|Taileron A" 
+    p = 30+TT_TLRN_B; List_Text[p] = "Taileron B";  --List_Text_Img[p]  = "x.png|Taileron B" 
+    p = 30+TT_TLRN_A_R2; List_Text[p] = "Taileron A + 2x Rud";  --List_Text_Img[p]  = "x.png|Taileron A + Dual Rud" 
+    p = 30+TT_TLRN_B_R2; List_Text[p] = "Taileron B + 2x Rud";  --List_Text_Img[p]  = "x.png|Taileron B + Dual Rud" 
+
+    -- Servo Reverse
+    List_Text[45+MT_NORMAL]  = "Normal"
+    List_Text[45+MT_REVERSE] = "Reverse"
+end
+
+-- Initial Setup
+local function ST_Init()
+    ST_Init_Text(0)
+    gc()
+ 
+    -- Setup default Data if no data loaded
+    menuDataChanged = false
+    if (M_DB[MV_AIRCRAFT_TYPE]==nil) then
+      ST_Default_Data()
+      menuDataChanged = true
+    end
+
+    currATyp = M_DB[MV_AIRCRAFT_TYPE]
+    currWTyp = M_DB[MV_WING_TYPE]
+    currTTyp = M_DB[MV_TAIL_TYPE]
+
+    Phase = PH_RX_VER
+end
+
+----- Line Type
+
+local function isSelectable(line)
+  if (line.Type == LT_MENU and line.ValId == line.MenuId) then return false end -- Menu to same page
+  if (line.Type ~= LT_MENU and  line.Max == 0) then return false end            -- Read only data line 
+  if (line.Type ~= 0 and line.TextId < 0x8000) then return true end          -- Not Flight Mode
+  return false;
+end
+
+local function isListLine(line) 
+  return line.Type==LT_LIST_NC
+end
+
+local function isEditing() 
+  return  ctx_EditLine ~= nil
+end
+
+-----------------------
+local function Get_Text(index)
+  local out = Text[index] or string.format("Unknown_%X", index)
+  return out
+end
+
+local function Get_Text_Value(index)
+  local out = List_Text[index] or Get_Text(index)
+  return out
+end
+
+function ChangePhase(newPhase)
+  Phase = newPhase
+end
+
+local function Value_Add(dir)
+  local line = MenuLines[ctx_SelLine]
+  local inc = dir
+
+  line.Val = line.Val + inc
+
+  if line.Val > line.Max then
+    line.Val = line.Max
+  elseif line.Val < line.Min then
+    line.Val = line.Min
+  end
+end
+--------------
+
+local function GotoMenu(menuId, lastSelectedLine)
+  Menu.MenuId = menuId
+  ctx_SelLine = lastSelectedLine
+  ChangePhase(PH_TITLE)
+end
+
+local function DSM_HandleEvent(event)
+  if event == EVT_VIRTUAL_EXIT then
+    if Phase == PH_RX_VER then
+      Phase = PH_EXIT_DONE -- Exit program
+    else
+      if isEditing() then   -- Editing a Line, need to  restore original value
+        MenuLines[ctx_EditLine].Val = originalValue
+        event = EVT_VIRTUAL_ENTER
+      else
+        if (Menu.BackId > 0 ) then -- Back??
+          ctx_SelLine = -1 --Back Button
+          event = EVT_VIRTUAL_ENTER
+        else
+          ChangePhase(PH_EXIT_REQ)
+        end
+      end
+    end
+  end -- Exit
+
+  if Phase == PH_RX_VER then return end -- nothing else to do 
+
+  if event == EVT_VIRTUAL_NEXT then
+    if isEditing() then -- Editting?
+      Value_Add(1)
+    else
+      if ctx_SelLine < 7 then -- On a regular line
+        local num = ctx_SelLine -- Find the prev selectable 
+        for i = ctx_SelLine + 1, 6, 1 do
+          local line = MenuLines[i]
+          if isSelectable(line) then
+            ctx_SelLine = i
+            break
+          end
+        end
+        if num == ctx_SelLine then       -- No Selectable Line
+          if Menu.NextId ~= 0 then
+            ctx_SelLine = 7 -- Next 
+          elseif Menu.PrevId ~= 0 then
+            ctx_SelLine = 8 -- Prev
+          end
+        end
+      elseif Menu.PrevId ~= 0 then
+        ctx_SelLine = 8 -- Prev
+      end
+    end
+    return
+  end
+  
+  if event == EVT_VIRTUAL_PREV then
+    if isEditing() then -- In Edit Mode
+      Value_Add(-1)
+    else
+      if ctx_SelLine == 8 and Menu.NextId ~= 0 then
+        ctx_SelLine = 7 -- Next 
+      elseif ctx_SelLine > 0 then
+        if ctx_SelLine > 6 then
+          ctx_SelLine = 7 --NEXT 
+        end
+        local num = ctx_SelLine -- Find Prev Selectable line
+        for i = ctx_SelLine - 1, 0, -1 do
+          local line = MenuLines[i]
+          if isSelectable(line) then
+            ctx_SelLine = i
+            break
+          end
+        end
+        if num == ctx_SelLine then   -- No Selectable Line
+          if (Menu.BackId > 0) then 
+            ctx_SelLine = -1 -- Back 
+          end
+        end
+      else
+        ctx_SelLine = -1   -- Back
+      end
+    end
+    return
+  end
+  
+
+  if event == EVT_VIRTUAL_ENTER then
+    if ctx_SelLine == -1 then    -- Back
+      GotoMenu(Menu.BackId, 0x80)
+    elseif ctx_SelLine == 7 then -- Next
+      GotoMenu(Menu.NextId, 0x82)
+    elseif ctx_SelLine == 8 then -- Prev
+      GotoMenu(Menu.PrevId, 0x81)
+    elseif ctx_SelLine >= 0 and MenuLines[ctx_SelLine].Type == LT_MENU then
+      GotoMenu(MenuLines[ctx_SelLine].ValId, ctx_SelLine)  -- ValId is the next menu
+    else
+      -- value entry
+      if isEditing() then
+        ctx_EditLine = nil   -- Done Editting
+        ChangePhase(PH_VAL_EDIT_END)
+      else   -- Start Editing
+        ctx_EditLine = ctx_SelLine
+        originalValue = MenuLines[ctx_SelLine].Val
+        ChangePhase(PH_VAL_EDITING)
+      end
+    end
+  end
+end
+
+local function DSM_Send_Receive()
+
+    if Phase == PH_RX_VER then -- request RX version
+        Phase = PH_TITLE
+        Menu.MenuId = 0x01001
+        Refresh_Display = true
+    elseif Phase == PH_WAIT_CMD then 
+        
+    elseif Phase == PH_TITLE then -- request menu title
+        ST_LoadMenu(Menu.MenuId)
+        if (Phase~=PH_EXIT_DONE) then
+          Phase = PH_WAIT_CMD
+        end
+        Refresh_Display = true
+    elseif Phase == PH_VAL_EDIT_END then -- send value
+        local line = MenuLines[ctx_SelLine] -- Updated Value of SELECTED line
+        
+        -- Update the menu data from the line
+        if (M_DB[line.ValId] ~= line.Val ) then
+            M_DB[line.ValId] = line.Val 
+            print(string.format("MENU_DATA[%d/%s]=%d",line.ValId,line.Text, line.Val))
+            menuDataChanged=true
+        end
+
+        -- Did the Wing type change?
+        local wt = M_DB[MV_WING_TYPE]
+        if (currWTyp ~= wt) then
+            currWTyp = wt
+            ST_PlaneWingInit(currWTyp)
+        
+            -- DELTA has only RUDER 
+            if (currWTyp==WT_ELEVON_A or currWTyp==WT_ELEVON_B) then
+              M_DB[MV_TAIL_TYPE] = TT_R1
+            end
+        end
+
+        --- Did the tail changed?
+        local tt = M_DB[MV_TAIL_TYPE]
+        if (currTTyp ~= tt) then
+            if (not tailTypeCompatible(currTTyp,tt)) then  
+              ST_PlaneTailInit(tt)
+            end
+            currTTyp = tt
+        end
+
+        Phase = PH_WAIT_CMD
+    elseif Phase == PH_EXIT_REQ then
+       Phase=PH_EXIT_DONE
+    end
+end
+
+-----
+
+local function showBitmap(x, y, imgDesc)
+  local f = string.gmatch(imgDesc, '([^%|]+)')   -- Iterator over values split by '|'
+  local imgName, imgMsg = f(), f()
+
+  f = string.gmatch(imgMsg or "", '([^%:]+)')   -- Iterator over values split by ':'
+  local p1, p2 = f(), f()
+
+  lcd.drawText(x, y, p1 or "", TEXT_ATTR)                     -- Alternate Image MSG
+  lcd.drawText(x, y + LCD_Y_LINE_HEIGHT, p2 or "", TEXT_ATTR) -- Alternate Image MSG
+  gc()
+end
+
+
+local function drawButton(x, y, text, active)
+  local attr = TEXT_ATTR
+  if (active) then attr = attr + INVERS end
+  lcd.drawText(x, y, text, attr)
+end
+
+local function DSM_Display()
+  lcd.clear()
+  --Draw RX Menu
+  if Phase == PH_RX_VER then
+    return
+  end
+
+    -- display Program version or RX version
+  local msg =  "FProg "..VERSION
+  lcd.drawText(40, LCD_Y_LOWER_BUTTONS, msg, TEXT_ATTR) 
+
+  if Menu.MenuId == 0 then return end; -- No Title yet
+
+  -- Got a Menu
+  lcd.drawText(1, 0, Menu.Text, TEXT_ATTR + INVERS)
+
+  local y = LCD_Y_LINE_HEIGHT + 2
+  for i = 0, 6 do
+    local attrib = TEXT_ATTR
+    if (i == ctx_SelLine) then attrib = attrib + INVERS end     -- Selected Line
+
+    local line = MenuLines[i]
+
+    if line ~= nil and line.Type ~= 0 then
+      local heading = line.Text 
+
+        local text = nil
+        if line.Type ~= LT_MENU then       -- list/value
+          if line.Val ~= nil then
+            if isListLine(line) then
+              local textId = line.Val + line.TextStart
+              text = Get_Text_Value(textId)
+
+              --local imgDesc = List_Text_Img[textId]
+             
+              --if (imgDesc and i == ctx_SelLine) then             -- Optional Image and Msg for selected value
+              --  showBitmap(1, 20, imgDesc)
+              --end
+            else
+              text = line.Val
+            end
+          end -- if is Value
+
+          if (ctx_EditLine == i) then  -- Editing a Line
+            attrib = BLINK + INVERS + TEXT_ATTR
+          end
+          lcd.drawText(LCD_X_MAX, y, text or "--", attrib + RIGHT) -- display value
+          --lcd.drawText(LCD_X_MAX, y, line.Format or "", TEXT_ATTR + RIGHT) -- display Format
+          attrib = TEXT_ATTR
+        end
+
+      lcd.drawText(1, y, heading, attrib) -- display text
+    end
+    y = y + LCD_Y_LINE_HEIGHT
+  end     -- for
+
+  if Menu.BackId~=0 then
+    drawButton(LCD_X_RIGHT_BUTTONS, 0, "Back", ctx_SelLine == -1)
+  end
+
+  if Menu.NextId~=0 then
+    drawButton(LCD_X_RIGHT_BUTTONS, LCD_Y_LOWER_BUTTONS, "Next", ctx_SelLine == 7)
+  end
+
+  if Menu.PrevId~=0 then
+    drawButton(1, LCD_Y_LOWER_BUTTONS, "Prev", ctx_SelLine == 8)
+  end
+end
+
+------------------------------------------------------------------------------------------------------------
+-- Init
+local function DSM_Init()
+  --LOG_open()
+  ST_Init()
+  gc()
+
+  if (LCD_W > 128) then
+    TEXT_ATTR = 0
+    LCD_Y_LINE_HEIGHT = 25
+    LCD_X_MAX         = 300
+    LCD_X_RIGHT_BUTTONS = LCD_X_MAX - 30
+
+    LCD_Y_LOWER_BUTTONS = (8 * LCD_Y_LINE_HEIGHT) + 2
+  end
+
+  Phase = PH_RX_VER
+end
+
+-- Main
+
+local function DSM_Run(event)
+  if event == nil then
+    error("Cannot be run as a model script!")
+    return 2
+  end
+
+  DSM_Display()
+  DSM_HandleEvent(event)
+  DSM_Send_Receive()
+  gc()
+
+  if Phase == PH_EXIT_DONE then
+    LOG_close()
+    return 2
+  else
+    return 0
+  end
+end
+
+---
+-- Load Model Config 
+gc()
+local r = assert(loadScript(DSMLIB_PATH.."DsmMIN_P1.lua"), "Not-Found: DSMLIB/DsmMIN_P1.lua")
+        (MODEL,M_DB, LOG_write)
+gc()
+----
+return { init = DSM_Init, run = DSM_Run }

Lua_scripts/DSMLIB/DsmMIN_P1.lua

@@ -0,0 +1,167 @@
+local MODEL, M_DATA, LOG_write = ...
+
+--[[
+local MODEL = {
+    modelName = "",            -- The name of the model comming from OTX/ETX
+    hashName = "",
+    modelOutputChannel = {},   -- Output information from OTX/ETX
+  
+    TX_CH_TEXT= { [0]=""}, 
+    PORT_TEXT = { [0]=""},
+  
+    DSM_ChannelInfo = {}       -- Data Created by DSM Configuration Script
+  }
+
+  -- MENU DATA Management
+local M_DATA = {}            -- Store the variables used in the Menus.
+
+--]]
+
+local DATA_PATH           = "/MODELS/DSMDATA"
+local TX_CHANNELS         = 12
+
+local MV_DATA_END        = 1040
+
+
+  local function hashName(mName)
+    local c=10000;
+  
+    local prefix = string.gsub(mName,"%.","_") -- Change any "." to "_"
+    prefix = string.gsub(prefix,"% ","_") -- Change any space to "_"
+    prefix = string.sub(prefix,1,5) -- Take the first 5 characters
+  
+    -- Simple Hash of the Model Name adding each character 
+    for i = 1, #mName do
+        local ch = string.byte(mName,i,i)
+        c=c+ch
+    end
+  
+    return (prefix .. c) -- Return Prefix + Hash
+  end
+  
+  -- Load Menu Data from a file 
+  local function ST_LoadFileData() 
+    local fname = hashName(MODEL.modelName)..".txt"
+    MODEL.hashName = fname
+  
+    -- Clear Menu Data
+    for i = 0, MV_DATA_END do
+        M_DATA[i]=nil
+    end
+  
+    print("Loading File:"..fname)
+  
+    local dataFile = io.open(DATA_PATH .. "/".. fname, "r")  -- read File 
+    -- cannot read file???
+    if (dataFile==nil) then return 0 end
+  
+    local line = io.read(dataFile, 5000)
+    io.close(dataFile)
+  
+    if #line == 0 then return 0 end -- No data??
+  
+    -- Process the input, each line is "Var_Id : Value" format 
+    -- Store it into MANU_DATA
+    local i=0
+    for k, v in string.gmatch(line, "(%d+):(%d+)") do
+        M_DATA[k+0]=v+0 -- do aritmentic to convert string to number
+        i=i+1
+    end
+  
+    -- Return 0 if no lines processed, 1 otherwise
+    if (i > 0) then return 1 else return 0 end
+  end
+
+  local function getModuleChannelOrder(num) 
+    --Determine fist 4 channels order
+    local ch_n={}
+    local st_n = {[0]= "R", "E", "T", "A" }
+    local c_ord=num -- ch order
+    if (c_ord == -1) then
+      ch_n[0] = st_n[3]
+      ch_n[1] = st_n[1]
+      ch_n[2] = st_n[2]
+      ch_n[3] = st_n[0]
+    else
+      ch_n[bit32.band(c_ord,3)] = st_n[3]
+      c_ord = math.floor(c_ord/4)
+      ch_n[bit32.band(c_ord,3)] = st_n[1]
+      c_ord = math.floor(c_ord/4)
+      ch_n[bit32.band(c_ord,3)] = st_n[2]
+      c_ord = math.floor(c_ord/4)
+      ch_n[bit32.band(c_ord,3)] = st_n[0]
+    end
+  
+    local s = ""
+    for i=0,3 do
+      s=s..ch_n[i]
+    end
+    return s
+  end
+  
+  local function ReadTxModelData()
+    local TRANSLATE_AETR_TO_TAER=false
+    local table = model.getInfo()   -- Get the model name 
+    MODEL.modelName = table.name
+  
+    local module = model.getModule(0) -- Internal
+    if (module==nil or module.Type~=6) then module = model.getModule(1) end -- External
+    if (module~=nil) then
+        if (module.Type==6 ) then -- MULTI-MODULE
+            local chOrder = module.channelsOrder
+            local s = getModuleChannelOrder(chOrder)
+            LOG_write("MultiChannel Ch Order: [%s]  %s\n",chOrder,s) 
+  
+            if (s=="AETR") then TRANSLATE_AETR_TO_TAER=true 
+            else TRANSLATE_AETR_TO_TAER=false 
+            end
+        end
+    end
+  
+    -- Read Ch1 to Ch10
+    local i= 0
+    for i = 0, TX_CHANNELS-1 do 
+        local ch = model.getOutput(i) -- Zero base 
+        if (ch~=nil) then
+            MODEL.modelOutputChannel[i] = ch
+            if (string.len(ch.name)==0) then 
+                ch.formatCh = string.format("TX:Ch%i",i+1)
+            else
+                ch.formatCh = string.format("TX:Ch%i/%s",i+1,ch.name or "--")
+            end
+        end
+    end
+  
+    -- Translate AETR to TAER
+  
+    if (TRANSLATE_AETR_TO_TAER) then 
+        LOG_write("Applying  AETR -> TAER translation\n") 
+        local ail = MODEL.modelOutputChannel[0]
+        local elv = MODEL.modelOutputChannel[1]
+        local thr = MODEL.modelOutputChannel[2]
+  
+        MODEL.modelOutputChannel[0] = thr
+        MODEL.modelOutputChannel[1] = ail
+        MODEL.modelOutputChannel[2] = elv
+    end
+  
+    -- Create the Port Text to be used 
+    LOG_write("Ports/Channels:\n") 
+    for i = 0, TX_CHANNELS-1 do 
+        local ch =  MODEL.modelOutputChannel[i]
+        if (ch~=nil) then
+            MODEL.TX_CH_TEXT[i] = ch.formatCh
+            MODEL.PORT_TEXT[i] = string.format("P%i (%s) ",i+1,MODEL.TX_CH_TEXT[i])  
+            LOG_write("Port%d %s [%d,%d] Rev=%d, Off=%d, ppmC=%d, syn=%d\n",i+1,MODEL.TX_CH_TEXT[i],math.floor(ch.min/10),math.floor(ch.max/10), ch.revert, ch.offset, ch.ppmCenter, ch.symetrical)
+        end
+    end
+  end
+  
+  -- Main Program
+
+  LOG_write("Reading Model Info\n")
+  ReadTxModelData()
+  local r = ST_LoadFileData()
+  return r
+  
+

Lua_scripts/DSMLIB/DsmMIN_P2.lua

@@ -0,0 +1,282 @@
+local MODEL, M_DATA, LOG_write = ...
+
+--[[
+local MODEL = {
+    modelName = "",            -- The name of the model comming from OTX/ETX
+    hashName = "",
+    modelOutputChannel = {},   -- Output information from OTX/ETX
+  
+    TX_CH_TEXT= { [0]=""}, 
+    PORT_TEXT = { [0]=""},
+  
+    DSM_ChannelInfo = {}       -- Data Created by DSM Configuration Script
+  }
+
+  -- MENU DATA Management
+local M_DATA = {}            -- Store the variables used in the Menus.
+
+--]]
+
+
+local TX_CHANNELS         = 12
+
+local AT_PLANE   = 0
+
+local aircraft_type_text = {[0]="Plane","Heli","Glider","Drone"}
+
+--[[
+local WT_A1       = 0
+local WT_A2       = 1
+local WT_FLPR     = 2
+local WT_A1_F1    = 3
+local WT_A2_F1    = 4
+local WT_A2_F2    = 5
+--]]
+local WT_ELEVON_A = 6
+local WT_ELEVON_B = 7
+
+local wing_type_text = {[0]="Normal","Dual Ail","Flapperon", "Ail + Flp","Dual Ail + Flp","Dual Ail/Flp","Elevon A","Elevon B"}
+
+--[[
+local TT_R1    = 0
+local TT_R1_E1 = 1
+local TT_R1_E2 = 2
+local TT_R2_E1 = 3
+local TT_R2_E2 = 4
+--]]
+
+local TT_VT_A  = 5
+local TT_VT_B  = 6
+local TT_TLRN_A = 7
+local TT_TLRN_B = 8
+local TT_TLRN_A_R2 = 9
+local TT_TLRN_B_R2 = 10
+
+local tail_type_text = {[0]="Rud Only","Normal","Rud + Dual Ele","Dual Rud + Elv","Dual Rud/Ele",
+            "VTail A","VTail B","Taileron A","Taileron B","Taileron A + Dual Rud","Taileron B + Dual Rud"}
+
+
+local MV_AIRCRAFT_TYPE = 1001
+local MV_WING_TYPE     = 1002
+local MV_TAIL_TYPE     = 1003
+        
+local MV_CH_BASE       = 1010
+local MV_CH_THR        = 1010
+local MV_CH_L_AIL      = 1011
+local MV_CH_R_AIL      = 1012
+local MV_CH_L_FLP      = 1013
+local MV_CH_R_FLP      = 1014
+
+local MV_CH_L_RUD      = 1015
+local MV_CH_R_RUD      = 1016
+local MV_CH_L_ELE      = 1017
+local MV_CH_R_ELE      = 1018
+
+local MV_PORT_BASE       = 1020
+
+local MV_DATA_END        = 1040
+
+--Channel Types --
+local CT_NONE     = 0x00
+local CT_AIL      = 0x01
+local CT_ELE      = 0x02
+local CT_RUD      = 0x04
+local CT_REVERSE  = 0x20
+local CT_THR      = 0x40
+local CT_SLAVE    = 0x80
+
+-- Seems like Reverse Mix is complement of the 3 bits
+local CMT_NORM     = 0x00   -- 0000
+local CMT_AIL      = 0x10   -- 0001 Taileron
+local CMT_ELE      = 0x20   -- 0010 For VTIAL and Delta-ELEVON
+local CMT_RUD      = 0x30   -- 0011 For VTIAL
+local CMT_RUD_REV  = 0x40   -- 0100 For VTIAL
+local CMT_ELE_REV  = 0x50   -- 0101 For VTIAL and Delta-ELEVON A
+local CMT_AIL_REV  = 0x60   -- 0110 Taileron 
+local CMT_NORM_REV = 0x70    -- 0111
+
+local MT_NORMAL      = 0
+local MT_REVERSE     = 1
+
+local function channelType2String(byte1, byte2) 
+    local s = ""
+  
+    if (byte2==0) then return s end;
+    
+    if (bit32.band(byte2,CT_AIL)>0) then s=s.."Ail" end
+    if (bit32.band(byte2,CT_ELE)>0) then s=s.."Ele" end
+    if (bit32.band(byte2,CT_RUD)>0) then s=s.."Rud" end
+    if (bit32.band(byte2,CT_THR)>0) then s=s.."Thr" end
+  
+    if (bit32.band(byte2,CT_REVERSE)>0) then s=s.."-" end
+  
+    if (bit32.band(byte2,CT_SLAVE)>0) then s=s.." Slv" end
+  
+    if (byte1==CMT_NORM) then s=s.." " 
+    elseif (byte1==CMT_AIL) then s=s.." M_Ail" 
+    elseif (byte1==CMT_ELE) then s=s.." M_Ele" 
+    elseif (byte1==CMT_RUD) then s=s.." M_Rud" 
+    elseif (byte1==CMT_RUD_REV) then s=s.." M_Rud-" 
+    elseif (byte1==CMT_ELE_REV) then s=s.." M_Ele-" 
+    elseif (byte1==CMT_AIL_REV) then s=s.." M_Ail-" 
+    elseif (byte1==CMT_NORM_REV) then s=s.." M-" 
+    end
+  
+    return s;
+  end
+  
+  -- This Creates the Servo Settings that will be used to pass to 
+-- Forward programming
+local function CreateDSMPortChannelInfo()
+    local function ApplyWingMixA(b2)
+        -- ELEVON
+        if (b2==CT_AIL+CT_ELE) then return CMT_ELE end; -- 0x03
+        if (b2==CT_AIL+CT_ELE+CT_SLAVE) then return CMT_NORM end; -- 0x83
+    end
+
+    local function ApplyWingMixB(b2)
+        -- ELEVON 
+        if (b2==CT_AIL+CT_ELE) then return CMT_NORM end; -- 0x03
+        if (b2==CT_AIL+CT_ELE+CT_SLAVE) then return CMT_ELE end; -- 0x83
+   end
+
+    local function ApplyTailMixA(b2)
+        -- VTAIL
+        -- Default normal/reverse behaviour 
+        if (b2==CT_RUD+CT_ELE) then return CMT_NORM end; -- 0x06
+        if (b2==CT_RUD+CT_ELE+CT_SLAVE) then return CMT_ELE end; -- 0x86
+
+        --TAILERON
+        -- Default normal/reverse behaviour 
+        if (b2==CT_AIL+CT_ELE) then return CMT_NORM end; -- 0x03
+        if (b2==CT_AIL+CT_ELE+CT_SLAVE) then return CMT_AIL end; -- 0x83
+    end
+
+    local function ApplyTailMixB(b2)
+        -- VTAIL 
+        -- Default normal/reverse behaviour 
+        if (b2==CT_RUD+CT_ELE) then return CMT_NORM end; -- 0x06
+        if (b2==CT_RUD+CT_ELE+CT_SLAVE) then return CMT_RUD end; -- 0x86
+
+        --TAILERON
+        if (b2==CT_AIL+CT_ELE) then return CMT_AIL end; -- 0x03
+        if (b2==CT_AIL+CT_ELE+CT_SLAVE) then return CMT_NORM end; -- 0x83
+    end
+
+    local function reverseMix(b)
+        if (b==CMT_NORM) then return CMT_NORM_REV end;
+        if (b==CMT_AIL) then return CMT_AIL_REV end;
+        if (b==CMT_ELE) then return CMT_ELE_REV end;
+        if (b==CMT_RUD) then return CMT_RUD_REV end;
+        return b
+    end
+
+    local DSM_Ch = MODEL.DSM_ChannelInfo 
+
+    for i=0, TX_CHANNELS-1 do
+        DSM_Ch[i] = {[0]= CMT_NORM, CT_NONE, nil}  -- Initialize with no special function 
+    end
+
+    --local aircraftType = M_DATA[MV_AIRCRAFT_TYPE]
+    local wingType = M_DATA[MV_WING_TYPE]
+    local tailType = M_DATA[MV_TAIL_TYPE]
+
+    local thrCh  =  M_DATA[MV_CH_THR]
+    local lAilCh =  M_DATA[MV_CH_L_AIL]
+    local rAilCh =  M_DATA[MV_CH_R_AIL]
+
+    local lElevCh = M_DATA[MV_CH_L_ELE]
+    local rElevCh = M_DATA[MV_CH_R_ELE]
+
+    local lRudCh = M_DATA[MV_CH_L_RUD]
+    local rRudCh = M_DATA[MV_CH_R_RUD]
+
+    -- Channels in menu vars are Zero base, Channel info is 1 based 
+    
+    -- THR 
+    if (thrCh~=nil and thrCh < 10) then DSM_Ch[thrCh][1]= CT_THR end
+
+    -- AIL (Left and Right)
+    if (lAilCh~=nil) then DSM_Ch[lAilCh][1] = CT_AIL  end
+    if (rAilCh~=nil) then DSM_Ch[rAilCh][1] = CT_AIL+CT_SLAVE end
+    -- ELE (Left and Right)
+    if (lElevCh~=nil) then DSM_Ch[lElevCh][1] = CT_ELE end
+    if (rElevCh~=nil) then DSM_Ch[rElevCh][1] = CT_ELE+CT_SLAVE end
+    -- RUD (Left and Right)
+    if (lRudCh~=nil) then DSM_Ch[lRudCh][1] = CT_RUD end
+    if (rRudCh~=nil) then DSM_Ch[rRudCh][1] = CT_RUD+CT_SLAVE end
+
+    -- VTAIL: RUD + ELE
+    if (tailType==TT_VT_A) then 
+        DSM_Ch[lElevCh][1] = CT_RUD+CT_ELE
+        DSM_Ch[rElevCh][1] = CT_RUD+CT_ELE+CT_SLAVE
+    elseif (tailType==TT_VT_B) then
+        DSM_Ch[lElevCh][1] = CT_RUD+CT_ELE+CT_SLAVE
+        DSM_Ch[rElevCh][1] = CT_RUD+CT_ELE
+    end
+
+    -- TAILERRON: 2-ELE + AIL
+    if (tailType==TT_TLRN_A or tailType==TT_TLRN_A_R2) then 
+        DSM_Ch[lElevCh][1] = CT_AIL+CT_ELE
+        DSM_Ch[rElevCh][1] = CT_AIL+CT_ELE+CT_SLAVE
+    elseif (tailType==TT_TLRN_B or tailType==TT_TLRN_B_R2) then
+        DSM_Ch[lElevCh][1] = CT_AIL+CT_ELE+CT_SLAVE
+        DSM_Ch[rElevCh][1] = CT_AIL+CT_ELE
+    end
+
+    ---- ELEVON :  AIL + ELE 
+    if (wingType==WT_ELEVON_A) then 
+        DSM_Ch[lAilCh][1] = CT_AIL+CT_ELE
+        DSM_Ch[rAilCh][1] = CT_AIL+CT_ELE+CT_SLAVE
+    elseif (wingType==WT_ELEVON_B) then
+        DSM_Ch[lAilCh][1] = CT_AIL+CT_ELE+CT_SLAVE
+        DSM_Ch[rAilCh][1] = CT_AIL+CT_ELE
+    end
+
+   ------MIXES ---------
+
+    -- TAIL Mixes (Elevator and VTail)
+    if (tailType==TT_VT_A or tailType==TT_TLRN_A or tailType==TT_TLRN_A_R2) then 
+        DSM_Ch[lElevCh][0] = ApplyTailMixA(DSM_Ch[lElevCh][1])
+        DSM_Ch[rElevCh][0] = ApplyTailMixA(DSM_Ch[rElevCh][1])
+    elseif (tailType==TT_VT_B or tailType==TT_TLRN_B or tailType==TT_TLRN_B_R2) then
+        DSM_Ch[lElevCh][0] = ApplyTailMixB(DSM_Ch[lElevCh][1])
+        DSM_Ch[rElevCh][0] = ApplyTailMixB(DSM_Ch[rElevCh][1])
+    end
+
+     ---- ELEVON :  AIL + ELE 
+     if (wingType==WT_ELEVON_A) then 
+        DSM_Ch[lAilCh][0] = ApplyWingMixA(DSM_Ch[lAilCh][1])
+        DSM_Ch[rAilCh][0] = ApplyWingMixA(DSM_Ch[rAilCh][1])
+    elseif (wingType==WT_ELEVON_B) then
+        DSM_Ch[lAilCh][0] = ApplyWingMixB(DSM_Ch[lAilCh][1])
+        DSM_Ch[rAilCh][0] = ApplyWingMixB(DSM_Ch[rAilCh][1])
+    end
+
+    -- Apply Gyro Reverse as needed for each channel as long as it is used 
+    for i=0, TX_CHANNELS-1 do
+        if (M_DATA[MV_PORT_BASE+i]==MT_REVERSE and DSM_Ch[i][1]>0) then
+            DSM_Ch[i][0]=reverseMix(DSM_Ch[i][0])
+            DSM_Ch[i][1]=DSM_Ch[i][1]+CT_REVERSE
+        end
+    end
+
+    -- Show how it looks
+    for i=0, 9 do
+        local b1,b2 =  DSM_Ch[i][0], DSM_Ch[i][1]
+        local s1 =  channelType2String(b1,b2)
+        local s = string.format("%s (%02X %02X)  %s\n", MODEL.PORT_TEXT[i],
+                    b1, b2,s1)
+        DSM_Ch[i][2]=s1
+        LOG_write(s) 
+    end
+
+    --MODEL.AirWingTailDesc = string.format("Aircraft(%s) Wing(%s) Tail(%s)",aircraft_type_text[aircraftType],wing_type_text[wingType],tail_type_text[tailType])
+end
+  
+  -- Main Program
+
+  LOG_write("Creating DSMPort Info\n")
+  CreateDSMPortChannelInfo()
+  
+

Lua_scripts/DSMLIB/DsmMainMenuLib.lua

@@ -1,5 +1,5 @@
 local Log, menuLib, modelLib, DEBUG_ON, SIMULATION_ON = ... -- Get DebugON from parameters
-local MAIN_MENU_LIB_VERSION = "0.55"
+local MAIN_MENU_LIB_VERSION = "0.56"
 local MODEL     = modelLib.MODEL
 
 local PHASE     = menuLib.PHASE

Lua_scripts/DSMLIB/DsmMenuLib.lua

@@ -547,8 +547,13 @@ function MenuLib.GetFlightModeValue(line)
         end
     else
         -- No adjustment needed
+        if (val==190) then
+            ret=ret.."Err:Out of Range"
+        else
             ret=ret..(val + 1)
         end
+        
+    end    
     return ret
 end
 

Lua_scripts/DSMLIB/DsmModelLib.lua

@@ -31,14 +31,15 @@ local CH_TYPE = {
 
 -- Seems like Reverse Mix is complement of the 3 bits
 local CH_MIX_TYPE = {
-    NORMAL       = 0x00,   -- 0000
-    MIX_AIL_B    = 0x10,   -- 0001 Taileron B
-    MIX_ELE_A    = 0x20,   -- 0010 For VTIAL and Delta-ELEVON A
-    MIX_ELE_B_REV= 0x30,   -- 0011 For VTIAL and Delta-ELEVON B
-    MIX_ELE_B    = 0x40,   -- 0100 For VTIAL and Delta-ELEVON B
-    MIX_ELE_A_REV= 0x50,   -- 0101 For VTIAL and Delta-ELEVON A
-    MIX_AIL_B_REV= 0x60,   -- 0110 Taileron B Rev
-    NORM_REV     = 0x70    -- 0111
+    MIX_NORM     = 0x00,   -- 0000
+    MIX_AIL      = 0x10,   -- 0001 Taileron
+    MIX_ELE      = 0x20,   -- 0010 For VTIAL and Delta-ELEVON
+    MIX_RUD      = 0x30,   -- 0011 For VTIAL
+
+    MIX_RUD_REV  = 0x40,   -- 0100 For VTIAL
+    MIX_ELE_REV  = 0x50,   -- 0101 For VTIAL and Delta-ELEVON A
+    MIX_AIL_REV  = 0x60,   -- 0110 Taileron 
+    MIX_NORM_REV = 0x70    -- 0111
 }
 
 local AIRCRAFT_TYPE = {
@@ -72,8 +73,11 @@ local TAIL_TYPE = {
     VTAIL_B      = 6,  -- 2
     TRAILERON_A  = 7,  -- 3
     TRAILERON_B  = 8,  -- 3
+    TRAILERON_A_R2  = 9,  -- 3
+    TRAILERON_B_R2  = 10  -- 3
 }
-local tail_type_text = {[0]="Rud Only","Normal","Rud + Dual Ele","Dual Rud + Elv","Dual Rud/Ele","VTail A","VTail B","Traileron A","Traileron B"}
+local tail_type_text = {[0]="Rud Only","Normal","Rud + Dual Ele","Dual Rud + Elv","Dual Rud/Ele",
+                        "VTail A","VTail B","Taileron A","Taileron B","Taileron A + 2x Rud","Taileron B + 2x Rud"}
 
 local CH_MODE_TYPE = {
     NORMAL      = 0,
@@ -156,18 +160,18 @@ local MENU_DATA = {}            -- Store the variables used in the Menus.
 
 -- DEFAULT Simple Plane Port configuration (The Configuration tool will overrride this)
 MODEL.DSM_ChannelInfo= {[0]= -- Start array at position 0
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.THR},    -- Ch1 Thr  (0x40)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.AIL},    -- Ch2 Ail  (0x01)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.ELE},    -- Ch2 ElE  (0x02)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.RUD},    -- Ch4 Rud  (0x04)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.NONE},   -- Ch5 Gear (0x00)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.NONE},   -- Ch6 Aux1 (0x00)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.NONE},   -- Ch7 Aux2 (0x00)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.NONE},   -- Ch8 Aux3 (0x00)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.NONE},   -- Ch9 Aux4 (0x00)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.NONE},   -- Ch10 Aux5 (0x00)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.NONE},   -- Ch11 Aux6 (0x00)
-                        {[0]=  CH_MIX_TYPE.NONE, CH_TYPE.NONE}    -- Ch12 Aux7 (0x00)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.THR},    -- Ch1 Thr  (0x40)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.AIL},    -- Ch2 Ail  (0x01)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.ELE},    -- Ch2 ElE  (0x02)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.RUD},    -- Ch4 Rud  (0x04)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE},   -- Ch5 Gear (0x00)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE},   -- Ch6 Aux1 (0x00)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE},   -- Ch7 Aux2 (0x00)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE},   -- Ch8 Aux3 (0x00)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE},   -- Ch9 Aux4 (0x00)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE},   -- Ch10 Aux5 (0x00)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE},   -- Ch11 Aux6 (0x00)
+                        {[0]=  CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE}    -- Ch12 Aux7 (0x00)
                     }   
 
 function ModelLib.printChannelSummary(a,w,t)
@@ -200,21 +204,24 @@ function ModelLib.channelType2String(byte1, byte2)
     local s = ""
 
     if (byte2==0) then return s end;
-    if (bit32.band(byte2,CH_TYPE.AIL)>0) then s=s.."AIL " end
-    if (bit32.band(byte2,CH_TYPE.ELE)>0) then s=s.."ELE " end
-    if (bit32.band(byte2,CH_TYPE.RUD)>0) then s=s.."RUD " end
-    if (bit32.band(byte2,CH_TYPE.THR)>0) then s=s.."THR " end
-    if (bit32.band(byte2,CH_TYPE.SLAVE)>0) then s=s.."SLAVE " end
-    if (bit32.band(byte2,CH_TYPE.REVERSE)>0) then s=s.."REVERSE " end
     
-    if (byte1==CH_MIX_TYPE.NORMAL) then s=s.." MIX_NOR" 
-    elseif (byte1==CH_MIX_TYPE.MIX_AIL_B) then s=s.." MIX_AIL_B" 
-    elseif (byte1==CH_MIX_TYPE.MIX_ELE_A) then s=s.." MIX_ELE_A" 
-    elseif (byte1==CH_MIX_TYPE.MIX_ELE_B_REV) then s=s.." MIX_ELE_B_Rev" 
-    elseif (byte1==CH_MIX_TYPE.MIX_ELE_B) then s=s.." MIX_ELE_B" 
-    elseif (byte1==CH_MIX_TYPE.MIX_ELE_A_REV) then s=s.." MIX_ELE_A_Rev" 
-    elseif (byte1==CH_MIX_TYPE.MIX_AIL_B_REV) then s=s.." MIX_AIL_B_Rev" 
-    elseif (byte1==CH_MIX_TYPE.NORM_REV) then s=s.." MIX_NOR_Rev" 
+    if (bit32.band(byte2,CH_TYPE.AIL)>0) then s=s.."Ail" end
+    if (bit32.band(byte2,CH_TYPE.ELE)>0) then s=s.."Ele" end
+    if (bit32.band(byte2,CH_TYPE.RUD)>0) then s=s.."Rud" end
+    if (bit32.band(byte2,CH_TYPE.THR)>0) then s=s.."Thr" end
+
+    if (bit32.band(byte2,CH_TYPE.REVERSE)>0) then s=s.."-" end
+
+    if (bit32.band(byte2,CH_TYPE.SLAVE)>0) then s=s.." Slv" end
+
+    if (byte1==CH_MIX_TYPE.MIX_NORM) then s=s.." " 
+    elseif (byte1==CH_MIX_TYPE.MIX_AIL) then s=s.." M_Ail" 
+    elseif (byte1==CH_MIX_TYPE.MIX_ELE) then s=s.." M_Ele" 
+    elseif (byte1==CH_MIX_TYPE.MIX_RUD) then s=s.." M_Rud" 
+    elseif (byte1==CH_MIX_TYPE.MIX_RUD_REV) then s=s.." M_Rud-" 
+    elseif (byte1==CH_MIX_TYPE.MIX_ELE_REV) then s=s.." M_Ele-" 
+    elseif (byte1==CH_MIX_TYPE.MIX_AIL_REV) then s=s.." M_Ail-" 
+    elseif (byte1==CH_MIX_TYPE.MIX_NORM_REV) then s=s.." M-" 
     end
 
     return s;
@@ -257,7 +264,7 @@ function ModelLib.ReadTxModelData()
   MODEL.modelName = table.name
 
   local module = model.getModule(0) -- Internal
-  if (module==nil) then module = model.getModule(1) end -- External
+  if (module==nil or module.Type~=6) then module = model.getModule(1) end -- External
   if (module~=nil) then
       if (module.Type==6 ) then -- MULTI-MODULE
           local chOrder = module.channelsOrder
@@ -307,11 +314,7 @@ function ModelLib.ReadTxModelData()
       local ch =  MODEL.modelOutputChannel[i]
       if (ch~=nil) then
           MODEL.TX_CH_TEXT[i] = ch.formatCh
-          if LCD_W <= 128 then -- SMALLER SCREENS
           MODEL.PORT_TEXT[i] = string.format("P%i (%s) ",i+1,MODEL.TX_CH_TEXT[i])
-          else
-              MODEL.PORT_TEXT[i] = string.format("Port%i (%s) ",i+1,MODEL.TX_CH_TEXT[i])
-          end
           
           Log.LOG_write("Port%d %s [%d,%d] Rev=%d, Off=%d, ppmC=%d, syn=%d\n",i+1,MODEL.TX_CH_TEXT[i],math.floor(ch.min/10),math.floor(ch.max/10), ch.revert, ch.offset, ch.ppmCenter, ch.symetrical)
       end
@@ -343,6 +346,11 @@ end
 function ModelLib.ST_LoadFileData() 
     local fname = ModelLib.hashName(MODEL.modelName)..".txt"
 
+    -- Clear Menu Data
+    for i = 0, MEMU_VAR.DATA_END do
+        MENU_DATA[i]=nil
+    end
+
     print("Loading File:"..fname)
 
     local dataFile = io.open(DATA_PATH .. "/".. fname, "r")  -- read File 
@@ -401,60 +409,45 @@ end
 function ModelLib.CreateDSMPortChannelInfo()
     local function ApplyWingMixA(b2)
         -- ELEVON
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE) then return CH_MIX_TYPE.MIX_ELE_A end; -- 0x03
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.MIX_ELE_A_REV end; -- 0x23
-       
-       -- Default normal/reverse behaviour 
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.NORMAL end; -- 0x83
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.NORM_REV end; -- 0xA3
+        if (b2==CH_TYPE.AIL+CH_TYPE.ELE) then return CH_MIX_TYPE.MIX_ELE end; -- 0x03
+        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_NORM end; -- 0x83
     end
 
     local function ApplyWingMixB(b2)
         -- ELEVON 
-        -- Default normal/reverse behaviour 
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE) then return CH_MIX_TYPE.NORMAL end; -- 0x03
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.NORM_REV end; -- 0x23
-
-        -- Difference with B 
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_ELE_A end; -- 0x83
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.MIX_ELE_A_REV  end; -- 0xA3
+        if (b2==CH_TYPE.AIL+CH_TYPE.ELE) then return CH_MIX_TYPE.MIX_NORM end; -- 0x03
+        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_ELE end; -- 0x83
    end
 
     local function ApplyTailMixA(b2)
         -- VTAIL
         -- Default normal/reverse behaviour 
-        if (b2==CH_TYPE.RUD+CH_TYPE.ELE) then return CH_MIX_TYPE.NORMAL end; -- 0x06
-        if (b2==CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.NORM_REV end; -- 0x26
-
-        if (b2==CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_ELE_A end; -- 0x86
-        if (b2==CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.SLAVE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.MIX_ELE_A_REV  end; -- 0xA6
+        if (b2==CH_TYPE.RUD+CH_TYPE.ELE) then return CH_MIX_TYPE.MIX_NORM end; -- 0x06
+        if (b2==CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_ELE end; -- 0x86
 
         --TAILERON
         -- Default normal/reverse behaviour 
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE) then return CH_MIX_TYPE.NORMAL end; -- 0x03
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.NORM_REV end; -- 0x23
-
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_AIL_B end; -- 0x83
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.MIX_AIL_B_REV end; -- 0xA3
-
+        if (b2==CH_TYPE.AIL+CH_TYPE.ELE) then return CH_MIX_TYPE.MIX_NORM end; -- 0x03
+        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_AIL end; -- 0x83
     end
 
     local function ApplyTailMixB(b2)
         -- VTAIL 
         -- Default normal/reverse behaviour 
-        if (b2==CH_TYPE.RUD+CH_TYPE.ELE) then return CH_MIX_TYPE.NORMAL end; -- 0x06
-        if (b2==CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.NORM_REV end; -- 0x26
-
-        if (b2==CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_ELE_B end; -- 0x86
-        if (b2==CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.SLAVE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.MIX_ELE_B_REV end; -- 0xA6
+        if (b2==CH_TYPE.RUD+CH_TYPE.ELE) then return CH_MIX_TYPE.MIX_NORM end; -- 0x06
+        if (b2==CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_RUD end; -- 0x86
 
         --TAILERON
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE) then return CH_MIX_TYPE.MIX_AIL_B end; -- 0x03
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.MIX_AIL_B_REV end; -- 0x23
+        if (b2==CH_TYPE.AIL+CH_TYPE.ELE) then return CH_MIX_TYPE.MIX_AIL end; -- 0x03
+        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.MIX_NORM end; -- 0x83
+    end
 
-        -- Default normal/reverse behaviour 
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE) then return CH_MIX_TYPE.NORMAL end; -- 0x83
-        if (b2==CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE+CH_TYPE.REVERSE) then return CH_MIX_TYPE.NORM_REV end; -- 0xA3
+    local function reverseMix(b)
+        if (b==CH_MIX_TYPE.MIX_NORM) then return CH_MIX_TYPE.MIX_NORM_REV end;
+        if (b==CH_MIX_TYPE.MIX_AIL) then return CH_MIX_TYPE.MIX_AIL_REV end;
+        if (b==CH_MIX_TYPE.MIX_ELE) then return CH_MIX_TYPE.MIX_ELE_REV end;
+        if (b==CH_MIX_TYPE.MIX_RUD) then return CH_MIX_TYPE.MIX_RUD_REV end;
+        return b
     end
 
 
@@ -462,7 +455,7 @@ function ModelLib.CreateDSMPortChannelInfo()
     local DSM_ChannelInfo = MODEL.DSM_ChannelInfo 
 
     for i=0, TX_CHANNELS-1 do
-        DSM_ChannelInfo[i] = {[0]= 0x00, CH_TYPE.NONE} -- Initialize with no special function 
+        DSM_ChannelInfo[i] = {[0]= CH_MIX_TYPE.MIX_NORM, CH_TYPE.NONE} -- Initialize with no special function 
     end
 
     local aircraftType = MENU_DATA[MEMU_VAR.AIRCRAFT_TYPE]
@@ -484,7 +477,7 @@ function ModelLib.CreateDSMPortChannelInfo()
     -- Channels in menu vars are Zero base, Channel info is 1 based 
     
     -- THR 
-    if (thrCh~=nil) then DSM_ChannelInfo[thrCh][1]= CH_TYPE.THR end
+    if (thrCh~=nil and thrCh < 10) then DSM_ChannelInfo[thrCh][1]= CH_TYPE.THR end
 
     -- AIL (Left and Right)
     if (lAilCh~=nil) then DSM_ChannelInfo[lAilCh][1] = CH_TYPE.AIL  end
@@ -497,59 +490,36 @@ function ModelLib.CreateDSMPortChannelInfo()
     if (rRudCh~=nil) then DSM_ChannelInfo[rRudCh][1] = CH_TYPE.RUD+CH_TYPE.SLAVE end
 
     -- VTAIL: RUD + ELE
-    if (tailType==TAIL_TYPE.VTAIL_A) then 
+    if (tailType==TAIL_TYPE.VTAIL_A or tailType==TAIL_TYPE.VTAIL_B) then 
         DSM_ChannelInfo[lElevCh][1] = CH_TYPE.RUD+CH_TYPE.ELE
         DSM_ChannelInfo[rElevCh][1] = CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.SLAVE
-    elseif (tailType==TAIL_TYPE.VTAIL_B) then
-        DSM_ChannelInfo[lElevCh][1] = CH_TYPE.RUD+CH_TYPE.ELE+CH_TYPE.SLAVE
-        DSM_ChannelInfo[rElevCh][1] = CH_TYPE.RUD+CH_TYPE.ELE
     end
 
-    -- TRAILERRON: 2-ELE + AIL
-    if (tailType==TAIL_TYPE.TRAILERON_A) then 
+    -- TAILERRON: 2-ELE + AIL
+    if (tailType==TAIL_TYPE.TRAILERON_A or tailType==TAIL_TYPE.TRAILERON_A_R2 or
+        tailType==TAIL_TYPE.TRAILERON_B or tailType==TAIL_TYPE.TRAILERON_B_R2) then 
         DSM_ChannelInfo[lElevCh][1] = CH_TYPE.AIL+CH_TYPE.ELE
         DSM_ChannelInfo[rElevCh][1] = CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE
-    elseif (tailType==TAIL_TYPE.TRAILERON_B) then
-        DSM_ChannelInfo[lElevCh][1] = CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE
-        DSM_ChannelInfo[rElevCh][1] = CH_TYPE.AIL+CH_TYPE.ELE
     end
 
     ---- ELEVON :  AIL + ELE 
-    if (wingType==WING_TYPE.ELEVON_A) then 
-        DSM_ChannelInfo[lAilCh][1] = CH_TYPE.AIL+CH_TYPE.ELE
-        DSM_ChannelInfo[rAilCh][1] = CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE
-    elseif (wingType==WING_TYPE.ELEVON_B) then
+    if (wingType==WING_TYPE.ELEVON_A or wingType==WING_TYPE.ELEVON_B) then 
         DSM_ChannelInfo[lAilCh][1] = CH_TYPE.AIL+CH_TYPE.ELE
         DSM_ChannelInfo[rAilCh][1] = CH_TYPE.AIL+CH_TYPE.ELE+CH_TYPE.SLAVE
     end
 
-    -- Apply Gyro Reverse as needed for each channel as long as it is used 
-    for i=0, TX_CHANNELS-1 do
-        if (MENU_DATA[MEMU_VAR.PORT_BASE+i]==CH_MODE_TYPE.REVERSE and DSM_ChannelInfo[i][1]>0) then
-            DSM_ChannelInfo[i][0]=DSM_ChannelInfo[i][1]+CH_MIX_TYPE.NORM_REV -- ALL REVERSE is 0x70 for normal
-            DSM_ChannelInfo[i][1]=DSM_ChannelInfo[i][1]+CH_TYPE.REVERSE
-        end
-    end
+    ------MIXES ---------
 
-    -- VTAIL: RUD + ELE
-    if (tailType==TAIL_TYPE.VTAIL_A) then 
+    -- TAIL Mixes (Elevator and VTail)
+    if (tailType==TAIL_TYPE.VTAIL_A or tailType==TAIL_TYPE.TRAILERON_A or tailType==TAIL_TYPE.TRAILERON_A_R2) then 
+        DSM_ChannelInfo[lElevCh][0] = ApplyTailMixA(DSM_ChannelInfo[lElevCh][1])
+        DSM_ChannelInfo[rElevCh][0] = ApplyTailMixA(DSM_ChannelInfo[rElevCh][1])
+    elseif (tailType==TAIL_TYPE.VTAIL_B or tailType==TAIL_TYPE.TRAILERON_B or tailType==TAIL_TYPE.TRAILERON_B_R2) then 
         DSM_ChannelInfo[lElevCh][0] = ApplyTailMixA(DSM_ChannelInfo[lElevCh][1])
         DSM_ChannelInfo[rElevCh][0] = ApplyTailMixA(DSM_ChannelInfo[rElevCh][1])
-    elseif (tailType==TAIL_TYPE.VTAIL_B) then
-        DSM_ChannelInfo[lElevCh][0] = ApplyTailMixB(DSM_ChannelInfo[lElevCh][1])
-        DSM_ChannelInfo[rElevCh][0] = ApplyTailMixB(DSM_ChannelInfo[rElevCh][1])
     end
 
-    -- TRAILERRON: ELE + AIL
-    if (tailType==TAIL_TYPE.TRAILERON_A) then 
-        DSM_ChannelInfo[lElevCh][1] = ApplyTailMixA(DSM_ChannelInfo[lElevCh][1])
-        DSM_ChannelInfo[rElevCh][1] = ApplyTailMixA(DSM_ChannelInfo[rElevCh][1])
-    elseif (tailType==TAIL_TYPE.TRAILERON_B) then
-        DSM_ChannelInfo[lElevCh][1] = ApplyTailMixB(DSM_ChannelInfo[lElevCh][1])
-        DSM_ChannelInfo[rElevCh][1] = ApplyTailMixB(DSM_ChannelInfo[rElevCh][1])
-    end
-
-     ---- ELEVON :  AIL + ELE 
+     ---- Wing Mixes 
      if (wingType==WING_TYPE.ELEVON_A) then 
         DSM_ChannelInfo[lAilCh][0] = ApplyWingMixA(DSM_ChannelInfo[lAilCh][1])
         DSM_ChannelInfo[rAilCh][0] = ApplyWingMixA(DSM_ChannelInfo[rAilCh][1])
@@ -558,6 +528,14 @@ function ModelLib.CreateDSMPortChannelInfo()
         DSM_ChannelInfo[rAilCh][0] = ApplyWingMixB(DSM_ChannelInfo[rAilCh][1])
     end
 
+    -- Apply Gyro Reverse as needed for each channel as long as it is used 
+    for i=0, TX_CHANNELS-1 do
+        if (MENU_DATA[MEMU_VAR.PORT_BASE+i]==CH_MODE_TYPE.REVERSE and DSM_ChannelInfo[i][1]>0) then
+            DSM_ChannelInfo[i][0]=reverseMix(DSM_ChannelInfo[i][0])
+            DSM_ChannelInfo[i][1]=DSM_ChannelInfo[i][1]+CH_TYPE.REVERSE
+        end
+    end
+
     -- Show how it looks
     for i=0, 9 do
         local b1,b2 =  DSM_ChannelInfo[i][0], DSM_ChannelInfo[i][1]
@@ -618,7 +596,8 @@ function ModelLib.ST_PlaneWingInit(wingType)
 end
 
 function ModelLib.ST_PlaneTailInit(tailType) 
-    if (MENU_DATA[MEMU_VAR.WING_TYPE]==WING_TYPE.ELEVON_A) then
+    if (MENU_DATA[MEMU_VAR.WING_TYPE]==WING_TYPE.ELEVON_A or
+        MENU_DATA[MEMU_VAR.WING_TYPE]==WING_TYPE.ELEVON_B) then
         tailType = TAIL_TYPE.RUD_1 -- Delta only have ruder  
     end
 
@@ -643,29 +622,29 @@ function ModelLib.ST_PlaneTailInit(tailType)
         MENU_DATA[MEMU_VAR.CH_L_RUD] = PORT.PORT4
     elseif (tailType == TAIL_TYPE.RUD_2_ELEV_1) then
         MENU_DATA[MEMU_VAR.CH_L_ELE] = PORT.PORT3
-        MENU_DATA[MEMU_VAR.CH_L_RUD] = PORT.PORT5
-        MENU_DATA[MEMU_VAR.CH_R_RUD] = PORT.PORT4
+        MENU_DATA[MEMU_VAR.CH_L_RUD] = PORT.PORT4
+        MENU_DATA[MEMU_VAR.CH_R_RUD] = PORT.PORT5
     elseif (tailType == TAIL_TYPE.RUD_2_ELEV_2) then
         MENU_DATA[MEMU_VAR.CH_L_ELE] = PORT.PORT5
         MENU_DATA[MEMU_VAR.CH_R_ELE] = PORT.PORT3
-        MENU_DATA[MEMU_VAR.CH_L_RUD] = PORT.PORT6
-        MENU_DATA[MEMU_VAR.CH_R_RUD] = PORT.PORT4
-    elseif (tailType == TAIL_TYPE.VTAIL_A) then
+        MENU_DATA[MEMU_VAR.CH_L_RUD] = PORT.PORT4
+        MENU_DATA[MEMU_VAR.CH_R_RUD] = PORT.PORT6
+    elseif (tailType == TAIL_TYPE.VTAIL_A or tailType == TAIL_TYPE.VTAIL_B) then
         MENU_DATA[MEMU_VAR.CH_L_ELE] = PORT.PORT4
         MENU_DATA[MEMU_VAR.CH_R_ELE] = PORT.PORT3
-    elseif (tailType == TAIL_TYPE.VTAIL_B) then
-        MENU_DATA[MEMU_VAR.CH_L_ELE]   = PORT.PORT3
-        MENU_DATA[MEMU_VAR.CH_R_ELE]  = PORT.PORT4
-    elseif (tailType == TAIL_TYPE.TRAILERON_A) then
-        MENU_DATA[MEMU_VAR.CH_L_ELE]  = PORT.PORT5
-        MENU_DATA[MEMU_VAR.CH_R_ELE] = PORT.PORT3
-    elseif (tailType == TAIL_TYPE.TRAILERON_B) then
+    elseif (tailType == TAIL_TYPE.TRAILERON_A or tailType==TAIL_TYPE.TRAILERON_A_R2 or
+            tailType == TAIL_TYPE.TRAILERON_B or tailType==TAIL_TYPE.TRAILERON_B_R2) then
+        MENU_DATA[MEMU_VAR.CH_L_RUD] = PORT.PORT4
         MENU_DATA[MEMU_VAR.CH_L_ELE] = PORT.PORT5
         MENU_DATA[MEMU_VAR.CH_R_ELE] = PORT.PORT3
     else -- Assume Normal 
         print("ERROR:invalid Tail Type")
     end
 
+    if (tailType == TAIL_TYPE.TRAILERON_A_R2 or tailType==TAIL_TYPE.TRAILERON_B_R2) then
+        MENU_DATA[MEMU_VAR.CH_R_RUD] = PORT.PORT7
+    end
+
     ModelLib.printChannelSummary()
 end
 

Lua_scripts/DSMLIB/DsmSetupMenuLib.lua

@@ -24,7 +24,7 @@
 ------------------------------------------------------------------------------
 
 local Log, menuLib, modelLib, DEBUG_ON, SIMULATION_ON = ... -- Get DebugON from parameters
-local SETUP_LIB_VERSION = "0.55"
+local SETUP_LIB_VERSION = "0.56"
 
 local DATA_PATH = modelLib.DATA_PATH
 
@@ -53,26 +53,61 @@ local currWingType = -1         -- Current TailType selected, and to detect chan
 local menuDataChanged = false   -- Flag to notify if any data has changed
 
 
+local function tailTypeCompatible(a,b)
 
+    local function normalize(tt)
+      if (tt==TAIL_TYPE.TRAILERON_A or tt==TAIL_TYPE.TRAILERON_B) then 
+        return TAIL_TYPE.TRAILERON_A
+    elseif (tt==TAIL_TYPE.TRAILERON_A_R2 or tt==TAIL_TYPE.TRAILERON_B_R2) then 
+        return TAIL_TYPE.TRAILERON_A_R2  
+      elseif (tt==TAIL_TYPE.VTAIL_A or tt==TAIL_TYPE.VTAIL_B) then
+        return TAIL_TYPE.VTAIL_A
+      else
+        return tt
+      end
+    end
+  
+    return (normalize(a)==normalize(b))
+  end
 
 
 -- Creates the menus to Render with the GUI
 local function ST_LoadMenu(menuId)
     local ctx = menuLib.DSM_Context
 
-    local function formatTXRevert(port)
-        if  (MODEL.modelOutputChannel[port].revert==0) then
-            return " (Tx:"..menuLib.Get_List_Text(300+CH_MODE_TYPE.NORMAL)..")"
-        else
-            return " (Tx:"..menuLib.Get_List_Text(300+CH_MODE_TYPE.REVERSE)..")"
+    local function portUse(p)
+        local out = "" 
+        if p==MENU_DATA[MEMU_VAR.CH_THR] then out = "Thr"
+        elseif p == MENU_DATA[MEMU_VAR.CH_L_AIL] then 
+            out=(MENU_DATA[MEMU_VAR.CH_R_AIL] and "Ail_L") or "Ail"
+        elseif p == MENU_DATA[MEMU_VAR.CH_R_AIL] then out="Ail_R"
+        elseif p == MENU_DATA[MEMU_VAR.CH_L_ELE] then 
+            out=(MENU_DATA[MEMU_VAR.CH_R_ELE] and "Ele_L") or "Ele"
+        elseif p == MENU_DATA[MEMU_VAR.CH_R_ELE] then out="Ele_R"
+        elseif p == MENU_DATA[MEMU_VAR.CH_L_RUD] then 
+            out=(MENU_DATA[MEMU_VAR.CH_R_RUD] and "Rud_L") or "Rud"
+        elseif p == MENU_DATA[MEMU_VAR.CH_R_RUD] then out="Rud_R"
+        elseif p == MENU_DATA[MEMU_VAR.CH_L_FLP] then 
+            out=(MENU_DATA[MEMU_VAR.CH_R_FLP] and "Flp_L") or "Flp"
+        elseif p == MENU_DATA[MEMU_VAR.CH_R_FLP] then out="Flp_R"
         end
+        return out
+    end
+
+    local function formatTXRevert(port)
+        local out = " " .. modelLib.channelType2String(MODEL.DSM_ChannelInfo[port][0], MODEL.DSM_ChannelInfo[port][1]);
+        return out
+    end
+
+    local function Header(p)
+        return MODEL.PORT_TEXT[p].." "..portUse(p)
     end
 
     menuLib.clearMenuLines()
 
     
     if (menuId==0x1000) then -- MAIN MENU
-        ctx.Menu = { MenuId = 0x1000, Text = "Save-Exit ("..MODEL.modelName..")", PrevId = 0, NextId = 0, BackId = 0xFFF9, TextId=0 }
+        ctx.Menu = { MenuId = 0x1000, Text = "Save-Exit ("..MODEL.modelName..")", PrevId = 0, NextId = 0, BackId = 0, TextId=0 }
        
         if (true) then
             ctx.MenuLines[4] = { Type = LINE_TYPE.MENU, Text="Save Changes", TextId = 0, ValId = 0x1005 }
@@ -128,6 +163,7 @@ local function ST_LoadMenu(menuId)
         ctx.SelLine = 6
         lastGoodMenu = menuId
     elseif (menuId==0x1010) then
+        modelLib.printChannelSummary()
         ctx.Menu = { MenuId = 0x1010, Text = "Aircraft Type", PrevId = 0, NextId = 0x1011, BackId = 0x1001, TextId=0 }
         ctx.MenuLines[5] = { Type = LINE_TYPE.LIST_MENU_NC, Text="Aircraft Type", TextId = 0, ValId = MEMU_VAR.AIRCRAFT_TYPE, Min=50, Max=53, Def=50, Val=MENU_DATA[MEMU_VAR.AIRCRAFT_TYPE] }
         ctx.SelLine = 5
@@ -135,7 +171,7 @@ local function ST_LoadMenu(menuId)
     elseif (menuId==0x1011) then
         ctx.Menu = { MenuId = 0x1011, Text = "Model Type:"..modelLib.aircraft_type_text[currAircraftType], PrevId = 0, NextId = 0x1020, BackId = 0x1010, TextId=0 }
         ctx.MenuLines[5] = { Type = LINE_TYPE.LIST_MENU_NC, Text="Wing Type", TextId = 0, ValId = MEMU_VAR.WING_TYPE, Min=100, Max=107, Def=100, Val=MENU_DATA[MEMU_VAR.WING_TYPE] }
-        ctx.MenuLines[6] = { Type = LINE_TYPE.LIST_MENU_NC, Text="Tail Type", TextId = 0, ValId = MEMU_VAR.TAIL_TYPE, Min=200, Max=208, Def=200, Val=MENU_DATA[MEMU_VAR.TAIL_TYPE] }
+        ctx.MenuLines[6] = { Type = LINE_TYPE.LIST_MENU_NC, Text="Tail Type", TextId = 0, ValId = MEMU_VAR.TAIL_TYPE, Min=200, Max=210, Def=200, Val=MENU_DATA[MEMU_VAR.TAIL_TYPE] }
         ctx.SelLine = 5
         lastGoodMenu = menuId
     elseif (menuId==0x1020) then
@@ -159,7 +195,7 @@ local function ST_LoadMenu(menuId)
 
         ctx.Menu = { MenuId = 0x1020, Text = title, PrevId = 0, NextId = 0x1021, BackId = 0x1011, TextId=0 }
 
-        ctx.MenuLines[0] = { Type = LINE_TYPE.LIST_MENU_NC, Text=thrText, TextId = 0, ValId = MEMU_VAR.CH_THR, Min=0, Max=9, Def=0, Val= thr }
+        ctx.MenuLines[0] = { Type = LINE_TYPE.LIST_MENU_NC, Text=thrText, TextId = 0, ValId = MEMU_VAR.CH_THR, Min=0, Max=10, Def=0, Val= thr }
 
         ctx.MenuLines[2] = { Type = LINE_TYPE.LIST_MENU_NC, Text=leftAilText, TextId = 0, ValId = MEMU_VAR.CH_L_AIL, Min=0, Max=9, Def=0, Val= leftAil }
 
@@ -174,7 +210,7 @@ local function ST_LoadMenu(menuId)
             ctx.MenuLines[5] = { Type = LINE_TYPE.LIST_MENU_NC, Text=rightFlapText, TextId = 0, ValId = MEMU_VAR.CH_R_FLP, Min=0, Max=9, Def=0, Val= rightFlap }
         end
 
-        ctx.SelLine = 1
+        ctx.SelLine = 0
         lastGoodMenu = menuId
 
     elseif (menuId==0x1021) then
@@ -216,14 +252,15 @@ local function ST_LoadMenu(menuId)
         lastGoodMenu = menuId
    
     elseif (menuId==0x1030) then
+        modelLib.CreateDSMPortChannelInfo()
         modelLib.printChannelSummary()
         
         ctx.Menu = { MenuId = 0x1030, Text = "Gyro Channel Reverse (Port 1-5)", PrevId = 0, NextId = 0x1031, BackId = 0x1001, TextId=0 }
-        ctx.MenuLines[0] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT1], TextId = 0, ValId = MEMU_VAR.PORT1_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT1_MODE], Format = formatTXRevert(PORT.PORT1) }
-        ctx.MenuLines[1] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT2], TextId = 0, ValId = MEMU_VAR.PORT2_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT2_MODE], Format = formatTXRevert(PORT.PORT2) }
-        ctx.MenuLines[2] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT3], TextId = 0, ValId = MEMU_VAR.PORT3_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT3_MODE], Format = formatTXRevert(PORT.PORT3) }
-        ctx.MenuLines[3] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT4], TextId = 0, ValId = MEMU_VAR.PORT4_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT4_MODE], Format = formatTXRevert(PORT.PORT4) }
-        ctx.MenuLines[4] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT5], TextId = 0, ValId = MEMU_VAR.PORT5_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT5_MODE], Format = formatTXRevert(PORT.PORT5) }
+        ctx.MenuLines[0] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT1), TextId = 0, ValId = MEMU_VAR.PORT1_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT1_MODE], Format = formatTXRevert(PORT.PORT1) }
+        ctx.MenuLines[1] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT2), TextId = 0, ValId = MEMU_VAR.PORT2_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT2_MODE], Format = formatTXRevert(PORT.PORT2) }
+        ctx.MenuLines[2] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT3), TextId = 0, ValId = MEMU_VAR.PORT3_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT3_MODE], Format = formatTXRevert(PORT.PORT3) }
+        ctx.MenuLines[3] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT4), TextId = 0, ValId = MEMU_VAR.PORT4_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT4_MODE], Format = formatTXRevert(PORT.PORT4) }
+        ctx.MenuLines[4] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT5), TextId = 0, ValId = MEMU_VAR.PORT5_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT5_MODE], Format = formatTXRevert(PORT.PORT5) }
 
         ctx.MenuLines[5] = { Type = LINE_TYPE.MENU, Text="Only Thr/Ail/Rud/Ele. This affects AS3X/SAFE reaction dir./b", TextId = 0, ValId = 0x1030 }
         ctx.MenuLines[6] = { Type = LINE_TYPE.MENU, Text="Any changes, use RX 'Relearn Servo Settings'/b", TextId = 0, ValId = 0x1030 }
@@ -231,13 +268,14 @@ local function ST_LoadMenu(menuId)
         ctx.SelLine = 0
         lastGoodMenu = menuId
     elseif (menuId==0x1031) then
+        modelLib.CreateDSMPortChannelInfo()
         modelLib.printChannelSummary()
         ctx.Menu = { MenuId = 0x1031, Text = "Gyro Channel Reverse (Port 6-10)", PrevId = 0x1030, NextId = 0, BackId = 0x1001, TextId=0 }
-        ctx.MenuLines[0] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT6], TextId = 0, ValId = MEMU_VAR.PORT6_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT6_MODE], Format = formatTXRevert(PORT.PORT6) }
-        ctx.MenuLines[1] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT7], TextId = 0, ValId = MEMU_VAR.PORT7_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT7_MODE], Format = formatTXRevert(PORT.PORT7) }
-        ctx.MenuLines[2] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT8], TextId = 0, ValId = MEMU_VAR.PORT8_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT8_MODE], Format = formatTXRevert(PORT.PORT8) }
-        ctx.MenuLines[3] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT9], TextId = 0, ValId = MEMU_VAR.PORT9_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT9_MODE], Format = formatTXRevert(PORT.PORT9) }
-        ctx.MenuLines[4] = { Type = LINE_TYPE.LIST_MENU_NC, Text=MODEL.PORT_TEXT[PORT.PORT10], TextId = 0, ValId = MEMU_VAR.PORT10_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT10_MODE], Format = formatTXRevert(PORT.PORT10) }
+        ctx.MenuLines[0] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT6), TextId = 0, ValId = MEMU_VAR.PORT6_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT6_MODE], Format = formatTXRevert(PORT.PORT6) }
+        ctx.MenuLines[1] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT7), TextId = 0, ValId = MEMU_VAR.PORT7_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT7_MODE], Format = formatTXRevert(PORT.PORT7) }
+        ctx.MenuLines[2] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT8), TextId = 0, ValId = MEMU_VAR.PORT8_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT8_MODE], Format = formatTXRevert(PORT.PORT8) }
+        ctx.MenuLines[3] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT9), TextId = 0, ValId = MEMU_VAR.PORT9_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT9_MODE], Format = formatTXRevert(PORT.PORT9) }
+        ctx.MenuLines[4] = { Type = LINE_TYPE.LIST_MENU_NC, Text=Header(PORT.PORT10), TextId = 0, ValId = MEMU_VAR.PORT10_MODE, Min=300, Max=301, Def=300, Val=MENU_DATA[MEMU_VAR.PORT10_MODE], Format = formatTXRevert(PORT.PORT10) }
      
         ctx.MenuLines[5] = { Type = LINE_TYPE.MENU, Text="Only Thr/Ail/Rud/Ele. This affects AS3X/SAFE reaction dir./b", TextId = 0, ValId = 0x1031 }
         ctx.MenuLines[6] = { Type = LINE_TYPE.MENU, Text="Any changes, use RX 'Relearn Servo Settings'/b", TextId = 0, ValId = 0x1031 }
@@ -321,18 +359,21 @@ local function ST_SendReceive()
 
             -- DELTA has only RUDER 
             if ((currWingType==WING_TYPE.ELEVON_A or currWingType==WING_TYPE.ELEVON_B) and TAIL_TYPE~=TAIL_TYPE.RUD_1) then
-                currTailType = TAIL_TYPE.RUD_1
+                MENU_DATA[MEMU_VAR.TAIL_TYPE] = TAIL_TYPE.RUD_1
             end
         end
 
         --- Did the tail changed?
-        if (currTailType ~= MENU_DATA[MEMU_VAR.TAIL_TYPE]) then
+        local ntt = MENU_DATA[MEMU_VAR.TAIL_TYPE]
+        if (currTailType ~= ntt) then
             if (currAircraftType==AIRCRAFT_TYPE.GLIDER) then
-                currTailType = MENU_DATA[MEMU_VAR.TAIL_TYPE]
+                currTailType = ntt
                 modelLib.ST_GliderTailInit(currTailType)
             else
-                currTailType = MENU_DATA[MEMU_VAR.TAIL_TYPE]
-                modelLib.ST_PlaneTailInit(currTailType)
+                if (not tailTypeCompatible(currTailType,ntt)) then
+                    modelLib.ST_PlaneTailInit(ntt)
+                end
+                currTailType = ntt
             end
         end
 
@@ -355,6 +396,7 @@ local function ST_Init_Text(rxId)
 
     -- Channel Names use the Port Text Retrived from OTX/ETX
     for i = 0, 9 do List_Text[i] = MODEL.PORT_TEXT[i]  end
+    List_Text[10]="--"
 
     -- Aircraft Type
     List_Text[50+AIRCRAFT_TYPE.PLANE]  = "Airplane";    --List_Text_Img[50+AIRCRAFT_TYPE.PLANE]   = "at_plane.png|Airplane" 
@@ -380,8 +422,11 @@ local function ST_Init_Text(rxId)
     List_Text[200+TAIL_TYPE.RUD_2_ELEV_2] = "Dual Rud + Dual Ele";  List_Text_Img[200+TAIL_TYPE.RUD_2_ELEV_2]  = "tt_2rud_2ele.png|Dual Rud + Dual Elev" 
     List_Text[200+TAIL_TYPE.VTAIL_A] = "V-Tail A";  List_Text_Img[200+TAIL_TYPE.VTAIL_A]  = "tt_vtail.png|V-Tail A" 
     List_Text[200+TAIL_TYPE.VTAIL_B] = "V-Tail B";  List_Text_Img[200+TAIL_TYPE.VTAIL_B]  = "tt_vtail.png|V-Tail B" 
-    List_Text[200+TAIL_TYPE.TRAILERON_A] = "Traileron A";  List_Text_Img[200+TAIL_TYPE.TRAILERON_A]  = "tt_traileron.png|Traileron A" 
-    List_Text[200+TAIL_TYPE.TRAILERON_B] = "Traileron B";  List_Text_Img[200+TAIL_TYPE.TRAILERON_B]  = "tt_traileron.png|Traileron B" 
+    List_Text[200+TAIL_TYPE.TRAILERON_A] = "Taileron A";  List_Text_Img[200+TAIL_TYPE.TRAILERON_A]  = "tt_taileron.png|Taileron A" 
+    List_Text[200+TAIL_TYPE.TRAILERON_B] = "Taileron B";  List_Text_Img[200+TAIL_TYPE.TRAILERON_B]  = "tt_taileron.png|Taileron B" 
+    List_Text[200+TAIL_TYPE.TRAILERON_A_R2] = "Taileron A + 2x Rud";  List_Text_Img[200+TAIL_TYPE.TRAILERON_A_R2]  = "tt_taileron2.png|Taileron A + Dual Rud" 
+    List_Text[200+TAIL_TYPE.TRAILERON_B_R2] = "Taileron B + 2x Rud";  List_Text_Img[200+TAIL_TYPE.TRAILERON_B_R2]  = "tt_taileron2.png|Taileron B + Dual Rud" 
+
 
     -- Servo Reverse
     if (LCD_W > 128) then
@@ -399,8 +444,9 @@ local function ST_Init()
     ST_Init_Text(0)
 
     -- Setup default Data, and load a file if exist
-    modelLib.ST_Default_Data()
+    --modelLib.ST_Default_Data()
     if (modelLib.ST_LoadFileData()==0) then -- Did not load a file
+        modelLib.ST_Default_Data()
         modelLib.ST_SaveFileData() -- Save Defaults
     end
     menuDataChanged = false

Lua_scripts/DSMLIB/DsmSimMenuLib.lua

@@ -26,7 +26,7 @@
 
 
 local Log, menuLib, modelLib, DEBUG_ON = ... -- Get DebugON from parameters
-local SIM_LIB_VERSION = "0.55"
+local SIM_LIB_VERSION = "0.56"
 local MSG_FILE = "/SCRIPTS/TOOLS/DSMLIB/msg_fwdp_en.txt"
 
 local PHASE = menuLib.PHASE

Lua_scripts/DSMLIB/MIN_msg_fwdp_en.txt

@@ -6,10 +6,5 @@
 T |0x0097|DONT USE: Factory Reset
 T |0x0098|DONT USE: Factory Reset
 T |0x00A5|DONT USE: First Time Setup
-T |0x00B0|Self-Lev/Ang Dem
-T |0x00CD|Level model & capt attitude
 T |0x0190|DONT USE: Relearn Servo Settings
 T |0x020D|DONT USE: First Time SAFE Setup
-T |0x0254|Pos = Up, Neg = Down
-T |0x0267|Pos = Nose Up/Roll Right
-T |0x0268|Neg = Nose Down/Roll Left

Lua_scripts/DSMLIB/msg_fwdp_en.txt

@@ -69,6 +69,10 @@ T |0x0053|Output Channel 3
 T |0x0054|Output Channel 4
 T |0x0055|Output Channel 5
 T |0x0056|Output Channel 6
+T |0x0057|Output Channel 7
+T |0x0058|Output Channel 8
+T |0x0059|Output Channel 9
+T |0x005A|Output Channel 10
 --
 -- FailSafe Options
 --LT|0x005E|Inh
@@ -143,7 +147,7 @@ T |0x00A5|First Time Setup
 T |0x00AA|Capture Gyro Gains
 T |0x00AD|Gain Channel Select
 T |0x00AF|Dynamic
-LT|0x00B0|Self-Level/Angle Dem
+LT|0x00B0|Self-Level
 LT|0x00B1|Envelope
 --
 -- Flight Modes List Options 
@@ -163,9 +167,9 @@ T |0x00BE|Unknown_BE -- Used in Reset menu (0x0001) while the RX is rebooting
 --
 T |0x00C7|Calibrate Sensor
 T |0x00C8|Sensor is Calibrating.. Wait 
-T |0x00CA|SAFE/Panic Mode Setup
+T |0x00CA|SAFE & Panic Mode Setup
 --
-T |0x00CD|Level model and capture attitude/m -- SPECIAL MENU to itself who is not a comment
+T |0x00CD|Level model & capt attitude/m -- SPECIAL MENU to itself who is not a comment
 T |0x00CE|Error TX Conf
 T |0x00CF|Invalid TX Ch Conf 1
 T |0x00D0|Invalid TX Ch Conf 2
@@ -382,7 +386,7 @@ T |0x0251|Are you sure you want to ovewrite the "Target"
 T |0x0252|with the "Source" ? 
 T |0x0253| -- Blank
 --
-T |0x0254|Postive = Up, Negative = Down
+T |0x0254|Pos = Up, Neg = Down
 --
 -- First time safe setup Page 1  (maybe ask to select Flight Mode cannel)
 T |0x0255|Before setting up SAFE
@@ -404,8 +408,8 @@ T |0x0262|by "Source"
 --
 T |0x0263|Fixed/Adjustable Gains/c/b
 T |0x0266|Heading Gain/c/b
-T |0x0267|Positive = Nose Up/Roll Right
-T |0x0268|Negative = Nose Down/Roll Left
+T |0x0267|Pos = Nose Up/Roll Right
+T |0x0268|Neg = Nose Down/Roll Left
 T |0x0269|SAFE - Thr to Pitch
 T |0x026A|Use CAUTION for Yaw gain!/b
 --

Lua_scripts/DSMLIB/readme.md

@@ -4,255 +4,19 @@ Rewrite/Enhancements by: Francisco Arzu
 
 Thanks to all the people volunteered to test it.
 
-# NOTE for FC6250HX FC+RX version
-For the full size FC6250HX, Only use V0.55 or newer.
+Release Notes for
 
-DO NOT use previous versions to do the Swashplate -> RX Orientation. The problem was that it did not have the orientation messages.. and you are choosing blind. The calibration will never stop until you place the RX in the right orientation, even after restarting the RX (if flashing red, is not in the right orientation.. if flashshing white is in the right orientation).  If you run into this problem, and lights are blinking red, rotate the FC on the longer axis until you get white blinking.. keep it stable, will blink white faster andlet calibration finishes.. after that is back to normal.
+## COLOR Radios
+Read more [Color radios](./readme_color.md) 
 
-# Introduction  (v0.55)
+![main-menu](https://user-images.githubusercontent.com/32604366/230751340-dd118f36-1884-405b-b12b-81cba16c7321.png)
+![flight-mode-setup](https://user-images.githubusercontent.com/32604366/230751281-0c71ff4a-179f-41fd-9290-302a6e0fe821.png)
 
-This script library enhances the original DSM Forward Programming tool. DSM Forward Programming is needed to setup many of the new Spektrum Receivers with Gyro AS3X/SAFE features. For the Gyro (/Safe) to correct the plane in flight, it needs to move the right surfaces therefore the RX needs to know the configuration of the plane (Wing Type, Tail Type, Mixers, Servo Assignments, Servo Reverse). That info tells the RX where the aileron(s) are (one or two), where the elevator(s) are (one or two),  V-Tail, Delta Wing, etc. 
+## Black & White Radios (Small Screens)
+Read more [black & whire radios](./readme_bw.md) 
 
-Since EdgeTx/OpenTx doesn’t have an equivalent setup that is stored in the radio, we have to create our own version. This info is stored inside the `/MODELS/DSMDATA` directory/folder (which needs to be created by manually).
-
-During `"Gyro Settings->initial setup"`, the RX asks the TX for model information behind the scenes.  After setup, `"Gyro Settings->System Tools-> Relearn Servo Settings"` requests the TX servo configuration and stores it in the RX. 
-
-# Deployment
-
-When upgrading from a previous version of this tool, delete your /SCRIPTS/TOOLS/DSMLIB before copying the new one (if you customized your images, inside "DSMLIB/img" do a backup first)
-
-Uncompress the Zip file (ZIP version) into your local computer.
-In another window, open your TX SDCard.
-
-1. The zip file has the same structure as your SDCard. If you want to copy all the content of the zip file into your SDCard top level folder, it will create all the directories and files in the right place.
-2. Make sure to check that  `/MODELS/DSMDATA` is there. The script will complain at startup if it does not exist. Here the script saves the Spektrun settings for each of your models.
-
-Your TX SDCard should looks like this:
-
-    /SCRIPTS/TOOLS/     -- you only need one of the 3 to save some space in your TOOLS screen
-        DSM FwdPrg_05_BW.lua      -- black/white text only 
-        DSM FwdPrg_05_Color.lua   -- Color and touch radios
-        DSM FwdPrg_05_MIN.lua     -- `NEW!` Minimalistic version for radios with LOW memory (cannot setup new planes)
-        
-    /SCRIPTS/TOOLS/DSMLIB/        -- (ALL CAPITALS) Libraries ane extra files
-            DsmFwPrgLib.lua       -- DSM Protocol Message and Menu   engine
-            DsmFwPrgSIMLib.lua    -- Simulation of AR631, FC6250HX  (For GUI development)
-            SetupLib.lua          -- Model Setup Screens
-            msg_fwdp_en.txt       -- `NEW!` Messages for forward programing externalized. To support other langs (english)
-	    ... a few other files
-
-    /SCRIPTS/TOOLS/DSMLIB/img                -- Images for RX orientations
-
-Other Directories
-
-    /MODELS/DSMDATA                 --(ALL CAPITALS) Data of model config (Wing Type, Servo Assignments)
-    /LOGS/dsm_log.txt		    --Readable log of the last RX/TX session, usefull for debugging problems
-
-
-
-# Common Questions
-1. `RX not accepting channels higher than Ch6 for Flight-mode o Gains:`
-- V0.55 and newer:  Problem solved.. Should allow you to select up to 12ch with the switch technique or with the scroller.
-
-- V0.53/0.54:  The RX is listening to channel changes for this options. Configure the Switch to the channel, togling once the switch will select the channel on the menu field.  
-
-2. `Only able to switch to Fligh-mode 2 and 3, but not 1:`
-Check that the module "Enable max throw" is OFF in you Multi-Module settings (where you do BIND), otherwise the TX signals will be out of range.
-The multi-module is already adjusting the TX/FrSky servo range internally to match Spektrum.
-
-3. `Why Ch1 says Ch1 (TX:Ch3/Thr)?`:
- Radios with Multi-Module are usually configured to work the standard AETR convention. Spektrum uses TAER. The multi-module does the conversion when transmitting the signals. So `Spektrum Ch1 (Throttle)` really comes from the `TX Ch3`.  We show both information (+name from the TX output).  If your multi-module/radio is setup as TAER, the script will not do the re-arrangement.  
-
-4. `If i change the model name, the original model settings are lost.` This is correct, the model name is used to generate the file name (inside /MODEL/DSMDATA) who stores the model configuration. Currently EdgeTx and OpenTX has differt features where i could get either the Model Name or the YAML file where the EdgeTX model configuration is stored.. to keep the code compatible, the model name is used.
-
-5. `Reversing a channel in my TX do not reverse the AS3X/SAFE reaction.` Correct, the chanel stick direction and the Gyro direction are two separate things.
-
-    5.1: First, you have setup your model so that the sticks and switches moves the surfaces in the right direction.
- 
-    5.2: Go to the script, `Model Setup` and setup your wing type, tail type, and select the channel assigment for each surface. Leave the servo settings the same as the values in the TX to start.
- 
-    5.3: Go to `Forward programming->Gyro Setting->Initial Setup` (New/factory reset), or `Forward programming->Gyro Setting->System Setup->Relearn Servo Settings` (not new). This will load your current Gyro servo settings into the plane's RX. This moves the current servo TX settings to the RX, so it is now in a known state.
- 
-    5.4: Verify that the AS3X and SAFE reacts in the proper direction. You can use the Flight mode configured as "Safe Mode: Auto-Level" to see if it moves the surfaces in the right direction.  
- 
-    5.5: If a surface don't move in the right direction, go to the `Model Setup->Gyro Channel Reverse` to reverse the Gyro on the channels needed, and do again the `Forward programming->Gyro Setting->System Setup->Relearn Servo Settings` to tranfer the new settings to the RX.
-
-    5.6: Specktrum TX always passes the TX servo reverse as the Gyro Reverse, but on many OpenTX/EdgeTX radios, the Rud/Ail are usually reversed by default compared to Specktrum. So far i don't think that i can use this as a rule, that is why the `Gyro Channel Reverse` page exist. 
-    
-
-
----
----
-
-# Changes and fixes 
-V0.55:
-1. Finally found where the TX reports to the RX how many channels is transmiting. The TX now reports itself as a 12ch radio instead of 6h. (DSM Multi-Module limit).  This fixes a few things:
-    
-    
-    a. Many places where you have to select channels > CH6 for Flight-Mode, Gains, Panic now works properly with the scroller. The radio is still validating that you are not selecting an invalid channel. For example, if you have an additional AIL on CH6, it will not allow you to use CH6 for FM or Gains.. it just move to the next valid one.
-
-    b. When setting up AIL/ELE on channels greater than CH6, on previous versions SAFE/AS3X was not moving them.. now they work up correctly.  Set them up in the first in CH1-CH10.  Why CH10?? Thats what fits on the reverse screen, otherwise, have to add more screens.
-
-    c. Some individual Gain channels was not allowing to setup on CH greater than CH6. Now is fixed.
-
-2. User Interface:
-    a. `RTN` Key now works as `Back` when the screen has a `Back`. Makes it easy for navigation.. Presing `RTN` on the main screen exists the tool.
-    b. Much faster refresh of the menus. Optimize the process of send/recive menu data from the RX.
-
-3. The TX now comunicates the SubTrim positions to the RX during `Relearn Servo Setting`. This changes the center of movement to one side or another. Really not much difference with small amounts of subtrim, previous versions where asuming subtrim of 0. When you have an extreame subtrim to one side, it was not moving simetrically.
-
-4. Support for FC6250HX (the one with separate RX).. Setup Swashplate type, RX orientation works properly.. This are menu options that the smaller version that comes in the
-Blade 230S did not have.
-
-
-V0.54:
-1. Fix a problem in the Attitude Trim page (`Gyro Settings->System Setup->SAFE/Panic Setup->Attitude Trim`). It was not saving the values after exiting the menu. This is to change what SAFE considers "Level" flying.
-2. Wings 2-Ail 2-Flaps had a bug on the 2nd flap.
-3. New Minimalistic script (`DsmFwdPrg_05_MIN.lua`): For radios with very low memory (FrSky QX7, RM Zorro, others). It can only change existing settings, but does not have the Plane Setup menus to setup a completly new plane.  In some radios, the very first time it runs (compile + run), it might give you a `not enouth memory` error.. try to run it again.
-4. External menu message file (DSMLIB/msg_fwdp_en.txt and MIN_msg_fwdp_en.txt).  Intial work to do localization and different languages.
-
-V0.53:
-1. Improved channel selection (Flight mode, Panic Channel, Gains Channel). Now during editing a channel, you can select any channel (>Ch4). Also, of you toggle the switch/channel it will populate the screen.
-2. Support for smaller screens (128x64) in B&W. The problem with this older radios is memory. In some, it does not have enouth memory to load the additional DSMLIB libraries.
-3. Fix formatting problem with some TX channel names who could affect the screen.. for example, rud channel should show "Ch4/rud", but shows "Ch4ud" because /r is for right justify formatting on messages. Now the formatting is only if it appears at the end of the message.
-
-V0.52:
-1. Menus to be able to configure Plane in a similar way as Spektrum Radio (v0.52)
-2. Make "Gyro Settings"->"Initial Setup" works (Tested on AR631,AR637xx with PLANE type of aircraft)
-3. Properly reset and restart after initial configuration and SAFE changes.
-4. Write Log of the conversation between RX/TX. To be used for debugging a problem is reported. 
-5. Provide a simulation of RX to do GUI development in Companion, and understand patterns of how the data is organized.
-
-
-# Tested Hardware
-- AR631/AR637xx
-- FC6250HX (Blade 230S V2 Helicopter; FC+RX in one, mini version)
-- FC6250HX (Separate RX.. use only V55 or newer of this tool)
-- AR636 (Blade 230S V1 Heli firmware 4.40)
-
-- Radiomaster TX16S  (All versions)
-
-Please report if you have tested it with other receivers to allow us to update the documentation. Code should work up to 10 channels for the main surfaces (Ail/Ele/etc).  All Spektrum RX are internally 20 channels, so you can use Ch7 for Flight Mode even if your RX is only 6 channels (See common Questions)
-
-
-# Messages Displayed in the GUI
-
-If in a screen you get text that looks like `Unknown_XX` (ex: Unknown_D3), that message has not been setup in the script in english. If you can determine what the proper message is,  you can send us a message to be added to the library.
-The `XX` represents a Hex Number (0..9,A..F)  message ID. 
-
-
-### Version 0.53 and older: 
-If you want to fix it in your local copy, all messages are towards the end in the file `SCRIPT\TOOS\DSMLIB\DsmFwPrgLib.lua`. Messages for Headers are stored in `Text` and messages for Options are stored in `List_Text`.  Lua scripts are text files, and can be edited with Notepad or equivalent.
-
-Portion of DsmFwPrgLib.lua:
-
-    Text[0x0097] = "Factory Reset"
-    Text[0x0098] = "Factory Reset" -- FC6250HX: Title
-    Text[0x0099] = "Advanced Setup"
-    Text[0x009A] = "Capture Failsafe Positions"
-    Text[0x009C] = "Custom Failsafe"
-
-    Text[0x009F] = "Save & Reset RX"  -- TODO: Find the Proper Spektrum Value ??
-
-    Text[0x00A5] = "First Time Setup"
-    Text[0x00AA] = "Capture Gyro Gains"
-    Text[0x00AD] = "Gain Channel Select"
-
-    -- Safe mode options, Inhibit + the values 
-    local safeModeOptions = {0x0003,0x00B0,0x00B1}  -- inh (gap), "Self-Level/Angle Dem, Envelope
-    List_Text[0x00B0] = "Self-Level/Angle Dem"
-    List_Text[0x00B1] = "Envelope"
-
-For example, if you get `Unknown_9D` in the GUI and your now that it should say **NEW Text**, you can edit the lua script to look like this:
-
-    Text[0x009A] = "Capture Failsafe Positions"
-    Text[0x009C] = "Custom Failsafe"
-
-    Text[0x009D] = "NEW Text" -- NEW Text added for AR98xx
-
-    Text[0x009F] = "Save & Reset RX"  -- TODO: Find the proper Spektrum text
-
-### Version 0.54 and newer:
-The menu messages are stored in DSMLIB/msg_fwdp_en.txt (For english). Just add the message there. MIN_msg_fwdp_en.txt has shorter messages overrides for screens who are smaller (for minimalistic 128x64 version).   The reference to the message file is at the file `/DSMLIB/DsmFwPrgLib.lua` if you want to change to use another language.
-
-    T |0x0097|Factory Reset
-    LT|0x00B0|Self-Level/Angle Dem
-    LT|0x00B1|Envelope
-
-
-# LOG File
-
-The log file of the last use of the script is located at `/LOGS/dsm_log.txt`. **It is overridden on every start to avoid filling up the SD card**. So if you want to keep it, copy or rename it before starting the script again. (it can be renamed in the TX by browsing the SD card)
-
-The log is human readable. The first number is the number of seconds since the start, and then what is the current state of the Library, and what has been sent and received. The info in the log can be easily used to create a new simulation for that RX in the future.
-
-Example Log:
-
-    5.340 WAIT_CMD: DSM_GotoMenu(0x1010,LastSelectedLine=0)
-    5.350 MENU_TITLE: SEND DSM_getMenu(MenuId=0x1010 LastSelectedLine=0)
-    5.440 MENU_TITLE: RESPONSE Menu: M[Id=0x1010 P=0x0 N=0x0 B=0x1000 Text="Gyro settings"[0xF9]]
-    5.490 MENU_LINES: SEND DSM_getFirstMenuLine(MenuId=0x1010)
-    5.590 MENU_LINES: RESPONSE MenuLine: L[#0 T=M VId=0x1011 Text="AS3X Settings"[0x1DD]   MId=0x1010 ]
-    5.640 MENU_LINES: SEND DSM_getNextLine(MenuId=0x1010,LastLine=0)
-    5.740 MENU_LINES: RESPONSE MenuLine: L[#1 T=M VId=0x1019 Text="SAFE Settings"[0x1E2]   MId=0x1010 ]
-    5.790 MENU_LINES: SEND DSM_getNextLine(MenuId=0x1010,LastLine=1)
-    5.850 MENU_LINES: RESPONSE MenuLine: L[#2 T=M VId=0x1021 Text="F-Mode Setup"[0x87]   MId=0x1010 ]
-    5.910 MENU_LINES: SEND DSM_getNextLine(MenuId=0x1010,LastLine=2)
-    5.970 MENU_LINES: RESPONSE MenuLine: L[#3 T=M VId=0x1022 Text="System Setup"[0x86]   MId=0x1010 ]
-    6.020 MENU_LINES: SEND DSM_getNextLine(MenuId=0x1010,LastLine=3
-
-# Validation of data by the RX
-
-The RX validates the data. if you change to an invalid channel or do a invalid number range, the RX will change it at the end of editing the field.
-
----
-# Version 0.53
-- Improve Channel selection in menus
-- Support smaller screens 128x64 in the black/white mode.
-
-# Version 0.52
-- Fix Reversing of Servos
-- Properly detect Multimodule Ch settings AETR 
----
-
-# Version 0.51  (volunteer testing version, not for production)
-- New Screens to Configure Model (Wing Type/Tail Tail, etc)
-- Finally got understanding that the previous unknown 0x05 lines are to send Model/Servo data to RX.
-- Fix use of AR636B (Firmware version 4.40.0 for Blade 230 heli, is the only one with Forward Programming)
-- Aircraft types:  Tested With Plane type only.. Glider and other in progress
-
-### Known Problems:
-- 4-Servo Wing type (Dual Ail/Tail) in planes give conflicting servo assignments by defaults.. Solution choose your own Ch.
-- Glider, Heli, Drone: Still in development. In glider, only a few wing type works.. needs to restrict menu options for the only valid one.
-
-
-# Version 0.5
-
-- Make the code more readable and understandable
-- Separate the DSM Forwards Programming logic from the GUI
-- Log the communication with the RX on a /LOGS/dsm_log.txt to allow to debug it easier 
-	and see the exchange of data between the RX/TX
-- Created a black/white Text only version with only Key/Roller Inputs
-- Created a nicer GUI for EdgeTX touch screen color Radios
-- RX simulation for GUI development:  turn on `SIMULATION_ON=true` in the beginning of the lua file
-- Test it on AR631, AR637xx, FC6250HX (Helicopter)
-
-### Some settings that can change (top of Lua file):
-    SIMULATION_ON = false   -- FALSE: hide similation menu (DEFAULT), TRUE: show RX simulation menu 
-	DEBUG_ON = 1           -- 0=NO DEBUG, 1=HIGH LEVEL 2=LOW LEVEL   (Debug logged into the /LOGS/dsm_log.txt)
-	USE_SPECKTRUM_COLORS = true -- true: Use spectrum colors, false: use theme colors (default on OpenTX, OpenTX handle colors different) 
-
-
-### Known Problems:
-1. **Incorrect List Value Options:** Some Menu List line (`LINE_TYPE.LIST_MENU1` or `L_m1` in logs), the range (min/max) of valid values seems to be incorrect, but the RX corrects the values.
-in the MINimalistic version, the RX is doing all the range validation, and will show invalid options temporarilly. In an Spektrum radio, it happens so fast, that you don't notice it, but in LUA scripts who are slower, you can see it in the screen. 
-In the COLOR version, The code has hardcoded the valid ranges to avoid this problem.
-
-2. Glider/Heli/Drone wing types not ready.
-
-For Helicopter, use airplane normal wing and normal tail
-
-
-# Version 0.2
-Original Version from Pascal Langer
+![image](https://github.com/frankiearzu/DSMTools/assets/32604366/be03ad40-3e2f-45e1-8f50-d231c3931169)
+![image](https://github.com/frankiearzu/DSMTools/assets/32604366/5010a361-1234-4c83-97b2-2eb6ae0d1061)
+![image](https://github.com/frankiearzu/DSMTools/assets/32604366/0d4e04dc-90d7-4322-9ad1-f57cbde49029)
+![IMG_3024](https://user-images.githubusercontent.com/32604366/230123260-614f4e5e-9546-4439-9196-db885894083f.jpg)
 

Lua_scripts/DSMLIB/readme_bw.md

@@ -0,0 +1,181 @@
+# Credits
+Code is based on the code/work by: Pascal Langer (Author of the Multi-Module) 
+Rewrite/Enhancements by: Francisco Arzu
+
+Thanks to all the people volunteered to test it.
+
+# Introduction  (v0.56 Black & White  Small Radios)
+
+!!!!!NEW!!!!!!: Finally was able to create the Plane Setup for Smaller Radios
+There is still significant memory limitations in some of this radios, so the Setup and FP was split in two files.
+The file 'DSM FwdPrg_56_STUP.lua' is the new one to create the planes setup that works together with 'DSM FwdPrg_56_MIN.lua'
+
+# How to Use it
+
+Step #1: Make sure that the /MODELS/DSMDATA folder exist.
+
+Step #2: Run the "DSM FwdPrg_56_STUP" first to setup the plane wing, tail and channels to use for each surface. At the end it will ask you to "save" the configuration. That saves a file in the /MODELS/DSMDATA folder.
+
+![image](https://github.com/frankiearzu/DSMTools/assets/32604366/be03ad40-3e2f-45e1-8f50-d231c3931169)
+![image](https://github.com/frankiearzu/DSMTools/assets/32604366/5010a361-1234-4c83-97b2-2eb6ae0d1061)
+![image](https://github.com/frankiearzu/DSMTools/assets/32604366/0d4e04dc-90d7-4322-9ad1-f57cbde49029)
+
+Why the RX needs to know the Plane Setup??   The AS3X/Gyro and SAFE needs to know what surfaces to move to do the proper correction in flight. It needs to know what channels are you using for ailerons, elevarors and rudders (could be 1 or 2 of each). Also if you have special Wing like a delta wing, the elevator and aileron functions are on the same channels.. same with V-Trails, Ruder/Elevator are combined. All this information is shared with the RX during "First Time Setup" as well as "Relearn Servo Setting".   Older version of 0.55 MIN hardcoded this info to be a plain 4-ch regular plane, thats why we discourage to use those function.
+
+
+Step #3: Run the "DSM FwdPrg_56_MIN". It uses the model configuration created in step #2 to properly tell the receiver the plane configuration for initial setup.  If you get "Cannot load model config", that means that the file was not created on step #2.   Once it shows the intial forward programming page for your receiver, usuall "Gyro Settings and Other Settings". You can properly setup the a plane from initial setup... if you are not familiar with this step, view some of the videos. There are already multiple videos showing how to do it EdgeTX color version, or the Spektrum official videos, the menus are the same.
+
+
+## Dealing with Low memory
+On my FrSky QX7 (Probably the one with the lower memory compared to Radiomaster Boxter and maybe Zorro), it will give you "not enouth memory"
+the very first time you try to run it since is compiling + running. Try to run them at least 2 times again, this times wll just run (not compile).
+In some ocations that keeps giving memory problems, i have to restart the radio, and try to run it right after restart.
+
+After it runs fine, and you try to run it the 2nd time and gives "not enouth memory", you have restart the radio.. for me this is random.. 
+sometimes i can run it many times consecutively.. but once it gives memory error, have to restart to be able to run again. 
+Once it starts, it should work find after... is the statup who loads what it needs to memory.
+
+I am running EdgeTX 2.9.2 (there was some memory cleanup in 2.9.0, and 2.9.1 to get a bit more memory)
+I left version 0.55 in the files, since it uses less memory, it can change the mayority of FP parameters, but cannot setup plane or Relearn Servo Settings
+(don't execute the menus who say 'DON'T USE!!').. v0.55 and v0.56 MINs can co-exist.
+
+Video of how to deal with memory:
+https://www.youtube.com/watch?v=kG3RfVa_brU
+
+# Deployment
+
+Uncompress the Zip file (ZIP version) into your local computer.
+In another window, open your TX SDCard and go to `/SCRIPTS/TOOLS`.
+
+When upgrading from a previous version of this tool, delete your `/SCRIPTS/TOOLS/DSMLIB` before copying the new one (if you customized the menu messages, inside `DSMLIB` do a backup of the message files first)
+
+1. The zip file has the same structure as your SDCard. If you want to copy all the content of the zip file into your SDCard, it will create all the directories and files in the right place.
+
+For the MINimalistic version, Your TX SDCard should looks like this:
+
+    /SCRIPTS/TOOLS
+        DSM FwdPrg_56_MIN.lua     -- Minimalistic version for radios with LOW memory (Can setup planes)
+        DSM FwdPrg_56_STUP.lua    -- `NEW!` Setup plane for minimalistic version (LOW Memory radios)
+        DSM FwdPrg_55_MIN.lua     -- Uses less memory than v56, but cannot do initial setup of the plane
+
+    /SCRIPTS/TOOLS/DSMLIB/       -- (ALL CAPITALS) Libraries ane extra files
+        DsmFwPrgMIN_P1.lua            -- Part1 of extra files for Min
+        DsmFwPrgMIN_P2.lua            -- Part2 of extra files for Min
+        msg_fwdp_en.txt               -- Menu messages in English  (common for all radios)
+        MIN_msg_fwdp_en.txt           -- Menu messages in English  (overrides for 128x164 resolution)
+
+### Other Directories/Files
+
+    /LOGS/dsm_log.txt		       	--Readable log of the last RX/TX session, usefull for debugging problems
+
+# NOTE for FC6250HX FC+RX version
+For the full size FC6250HX, Only use V0.55 or newer.
+
+DO NOT use previous versions to do the Setup -> Gyro Settings -> Orientation. The problem was that it did not have the orientation messages.. and you are were choosing blind. The calibration will never stop until you place the RX in the right orientation, even after restarting the RX (if flashing red, is not in the right orientation.. if flashshing white is in the right orientation).  If you run into this problem, and lights are blinking red, rotate the FC on the longer axis until you get white blinking.. keep it stable, will blink white faster andlet calibration finishes.. after that is back to normal.
+
+OpenTX: When you enter "forward programming" you will hear "Telemetry lost" and "Telemetry recovered".. The FC led will blink white, but when exit FP, will blink red...is not problem.. but will need to be power cycled to get blinking green again.. i think is something related to temporarilly loosing the connection with the radio..researching the OpenTX code since it only happens with this helis FC. 
+
+# Common Questions
+1. `RX not accepting channels higher than Ch6 for Flight-mode o Gains:`
+    - All Spektrum RX are 20 channels internally, even if it only has 6 external Ch/Ports to connect servos.
+
+    - Make sure that when you bind your RX, you select the proper range of channels to use.. By default, ch1-ch8.
+    
+    - You have to mapped a Switch/Slider to the channel, togling/moving  will select the channel on the menu field.
+
+    - The RX validates the channels, and it does not detect signal on a channel, it will not allow to select it..that is why is important to move the switch/slider, so that the RX knows that is a valid channel.   
+
+
+# Changes and fixes 
+
+v0.56:
+1. Fix Tail-Type "Taileron" functionality that was not working. Also validated V-Tail and Delta wings.
+2. Added Taileron and two Rudder config (Many Freewing Jets like F18,F16, etc)
+3. Gyro-Reverse Screen now shows what is the channel/port used for (Ail, Ele, Rud, etc)
+4. COLOR ONLY: Gyro-Reverse Screen now shows what information that shared with the RX about each channel (Role, Slave, Reverse).
+5. NEW!! Initial version of Plane Setup for B&W radios
+
+V0.55:
+1. Finally found where the TX reports to the RX how many channels is transmiting. The TX now reports itself as a 12ch radio instead of 6h. (DSM Multi-Module limit).  This fixes a few things:
+    
+    a. Many places where you have to select channels > CH6 for Flight-Mode, Gains, Panic now works properly with the scroller. The radio is still validating that you are not selecting an invalid channel. For example, if you have an additional AIL on CH6, it will not allow you to use CH6 for FM or Gains.. it just move to the next valid one.
+
+    b. When setting up AIL/ELE on channels greater than CH6, on previous versions SAFE/AS3X was not moving them.. now they work up correctly.  Set them up in the first in CH1-CH10.  Why CH10?? Thats what fits on the reverse screen, otherwise, have to add more screens.
+
+    c. Some individual Gain channels was not allowing to setup on CH greater than CH6. Now is fixed.
+
+2. User Interface:
+    a. `RTN` Key now works as `Back` when the screen has a `Back`. Makes it easy for navigation.. Presing `RTN` on the main screen exists the tool.
+    b. Much faster refresh of the menus. Optimize the process of send/recive menu data from the RX.
+
+3. Support for FC6250HX (the one with separate RX).. Setup Swashplate type, RX orientation works properly.. This are menu options that the smaller version that comes in the
+Blade 230S did not have.
+
+V0.54 Beta:
+- First version for the small screens, and limited memory.  Only can change existing values, it cannot setup a brand new plane or new RX from Zero
+- Fix problem on editing the SAFE Mode Attitude Trim
+- First version with externalize merges, so that it can be translated to other languages
+
+# Tested Radios and RXs
+- Radio: FrSky QX7:   Due to limited memory, could be that the first time is does not start (not enouth memory to compile+run), but try again after a fresh TX restart.
+
+- AR631/AR637xx
+- FC6250HX (Blade 230S V2 Helicopter)
+- FC6250HX (Separate RX.. use only V55 or newer of this tool)
+- AR636 (Blade 230S V1 Heli firmware 4.40)
+
+Please report if you have tested it with other receivers to allow us to update the documentation. Code should work up to 10 channels for the main surfaces (Ail/Ele/etc).  All Spektrum RX are internally 20 channels, so you can use Ch7 for Flight Mode even if your RX is only 6 channels (See common Questions)
+
+# Messages Displayed in the GUI
+
+If in a screen you get text that looks like `Unknown_XX` (ex: Unknown_D3), that message has not been setup in the script in english. If you can determine what the proper message is,  you can send us a message to be added to the library.
+The `XX` represents a Hex Number (0..9,A..F)  message ID. 
+
+If you want to fix it in your local copy, all messages are in the file `SCRIPT\TOOS\DSMLIB\msg_fwdp_en.txt`. (english version)
+
+Example::
+
+    T |0x0080|Orientation
+    T |0x0082|Heading
+    T |0x0085|Frame Rate
+    T |0x0086|System Setup
+    T |0x0087|F-Mode Setup
+    T |0x0088|Enabled F-Modes
+    T |0x0089|Gain Channel
+    T |0x008A|Gain Sensitivity/r  -- Right Align
+    T |0x008B|Panic
+    T |0x008E|Panic Delay
+
+For example, if you get `Unknown_9D` in the GUI and your now that it should say **NEW Text**, you can edit the lua script to look like this:
+    T |0x009D|NEW Text -- NEW Text added for AR98xx
+
+# Local Language Support 
+Some settings that can change (top of Lua file):
+`local LANGUAGE            = "en"`
+
+If you want to translate the menu messages to another language (like french), copy the file `msg_fwdp_en.txt` into `msg_fwdp_fr.txt`, translate it, and change the language in the lua file to `"fr"`.
+
+
+# LOG File
+
+The log file of the last use of the script is located at `/LOGS/dsm_log.txt`. **It is overridden on every start to avoid filling up the SD card**. So if you want to keep it, copy or rename it before starting the script again. (it can be renamed in the TX by browsing the SD card)
+
+The log is human readable, and can help use debug problems remotrly
+
+
+# Validation of data by the RX
+
+When you change a value in the GUI, the RX validates that the value is valid.  This applies to channels as well as values.
+
+
+---
+# Version 0.54
+First version for Small Radios
+
+### Known Problems:
+- Currently cannot setup a plane from scratch.. (Working on it).
+- The first time you run it, it will give you "not enouth memory", but should work the 2nd time after the first compilation (creation of .luac). After that, it should start right away.
+ 
+# Version 0.2
+Original Version from Pascal Langer
+ 

Lua_scripts/DSMLIB/readme_color.md

@@ -0,0 +1,284 @@
+# Credits
+Code is based on the code/work by: Pascal Langer (Author of the Multi-Module) 
+Rewrite/Enhancements by: Francisco Arzu
+
+Thanks to all the people volunteered to test it.
+
+# Introduction  (v0.56)
+
+NOTE: Unless you use special tail types, probably not worth the upgrade. The changes are mostly cosmetic on the Gyro Reverse page to show extra information.
+
+In 0.56, focused on validating and fixing the Wing and Tail type special mixing. Vtail/Delta was working but Taileron was not. The Gyro Reverse screen now show what type of servo information is sharing with the TX.  This affects the Gyro AS3X and SAFE behaviour, you still needs to set your TX with the proper mixes to do V-Tail/Taileron/etc.
+
+- The first is the "Role" of the port (`Ail/Ele/Rud/Thr`). Combination is posible for for special types of wing/tails: Vtail:`EleRud`, Delta & Taileron: `AilEle`.
+- The `-` (Minus) is Reverse.
+- Information is if it the Master or Slave (Master is implicit)
+- The type of mix applied: for V-Tail, the left/right Elevators (`EleRud`) uses `M_Rud` (Mix Rudder), For Delta, the left/right Ailerons (`AilEle`) uses `M_Ele` (Mix Elevator), and finally the Tailerons, the the left/right Elevators (`AilEle`) uses `M_Ail` (Mix Aileron).  Looks like the Mixes are for the entire RX and only needs to be set in one of the ports, The difference between the "A" and "B" configuration is just if the mix is set on the Master or Slave port (like Taileron_A or Taileron_B) and affects the direction.. sometimes you have to try both. Start by setting the right direction for the primary roll, and then use the A/B configurations. For exmaple, in Taileron, the primary roll is Elevators, the secondary roll is Aileron (Mix Aileron).    Below is a Taileron example: Two independent Elevators and 2 independent ailerons. 
+
+![image](https://github.com/frankiearzu/DSMTools/assets/32604366/4bbeb234-c92c-4663-b464-549df1c134a0)
+![image](https://github.com/frankiearzu/DSMTools/assets/32604366/f8fa62b4-9843-4d81-9c67-7c8bfcf252f2)
+
+
+With spektrum constantly updating its firmware, you only need to update the message file if you see in the screen any message "Unknown_xyz".
+
+
+This script library enhances the original DSM Forward Programming tool. DSM Forward Programming is needed to setup many of the new Spektrum Receivers with Gyro AS3X/SAFE features. For the Gyro (/Safe) to correct the plane in flight, it needs to move the right surfaces therefore the RX needs to know the configuration of the plane (Wing Type, Tail Type, Mixers, Servo Assignments, Servo Reverse). That info tells the RX where the aileron(s) are (one or two), where the elevator(s) are (one or two),  V-Tail, Delta Wing, etc. 
+
+Since EdgeTx/OpenTx doesn’t have an equivalent setup that is stored in the radio, we have to create our own version. This info is stored inside the `/MODELS/DSMDATA` directory/folder (which needs to be created by manually).
+
+During `"Gyro Settings->initial setup"`, the RX asks the TX for model information behind the scenes.  After setup, `"Gyro Settings->System Tools-> Relearn Servo Settings"` requests the TX servo configuration and stores it in the RX. 
+
+# Deployment
+
+When upgrading from a previous version of this tool, delete your /SCRIPTS/TOOLS/DSMLIB before copying the new one (if you customized your images, inside "DSMLIB/img" do a backup first). Also you can delete the previous DSM_FwdProg*.* from /SCRIPTS/TOOLS.
+
+Uncompress the Zip file (ZIP version) into your local computer.
+In another window, open your TX SDCard.
+
+1. The zip file has the same structure as your SDCard. If you want to copy all the content of the zip file into your SDCard top level folder, it will create all the directories and files in the right place.
+2. Make sure to check that  `/MODELS/DSMDATA` is there. The script will complain at startup if it does not exist. Here the script saves the Spektrun settings for each of your models.
+
+Your TX SDCard should looks like this:
+
+    /SCRIPTS/TOOLS/     -- you only need one of the 3 to save some space in your TOOLS screen
+        DSM FwdPrg_56_Color.lua   -- Color and touch radios
+
+        
+    /SCRIPTS/TOOLS/DSMLIB/        -- (ALL CAPITALS) Libraries ane extra files
+            DsmFwPrgLib.lua       -- DSM Protocol Message and Menu   engine
+            DsmFwPrgSIMLib.lua    -- Simulation of AR631, FC6250HX  (For GUI development)
+            SetupLib.lua          -- Model Setup Screens
+            msg_fwdp_en.txt       -- `NEW!` Messages for forward programing externalized. To support other langs (english)
+	    ... a few other files
+
+    /SCRIPTS/TOOLS/DSMLIB/img                -- Images for RX orientations
+
+Other Directories
+
+    /MODELS/DSMDATA                 --(ALL CAPITALS) Data of model config (Wing Type, Servo Assignments)
+    /LOGS/dsm_log.txt		    --Readable log of the last RX/TX session, usefull for debugging problems
+
+# NOTE for FC6250HX FC+RX version
+For the full size FC6250HX, Only use V0.55 or newer.
+
+DO NOT use previous versions to do the Setup -> Gyro Settings -> Orientation. The problem was that it did not have the orientation messages.. and you are were choosing blind. The calibration will never stop until you place the RX in the right orientation, even after restarting the RX (if flashing red, is not in the right orientation.. if flashshing white is in the right orientation).  If you run into this problem, and lights are blinking red, rotate the FC on the longer axis until you get white blinking.. keep it stable, will blink white faster andlet calibration finishes.. after that is back to normal.
+
+OpenTX: When you enter "forward programming" you will hear "Telemetry lost" and "Telemetry recovered".. The FC led will blink white, but when exit FP, will blink red...is not problem.. but will need to be power cycled to get blinking green again.. i think is something related to temporarilly loosing the connection with the radio..researching the OpenTX code since it only happens with this helis FC. 
+
+# Common Questions
+1. `RX not accepting channels higher than Ch6 for Flight-mode o Gains:`
+- V0.55 and newer:  Problem solved.. Should allow you to select up to 12ch with the switch technique or with the scroller.
+
+- V0.53/0.54:  The RX is listening to channel changes for this options. Configure the Switch to the channel, togling once the switch will select the channel on the menu field.  
+
+2. `Only able to switch to Fligh-mode 2 and 3, but not 1:`
+Check that the module "Enable max throw" is OFF in you Multi-Module settings (where you do BIND), otherwise the TX signals will be out of range.
+The multi-module is already adjusting the TX/FrSky servo range internally to match Spektrum.
+
+3. `Why Ch1 says Ch1 (TX:Ch3/Thr)?`:
+ Radios with Multi-Module are usually configured to work the standard AETR convention. Spektrum uses TAER. The multi-module does the conversion when transmitting the signals. So `Spektrum Ch1 (Throttle)` really comes from the `TX Ch3`.  We show both information (+name from the TX output).  If your multi-module/radio is setup as TAER, the script will not do the re-arrangement.  
+
+4. `If i change the model name, the original model settings are lost.` This is correct, the model name is used to generate the file name (inside /MODEL/DSMDATA) who stores the model configuration. Currently EdgeTx and OpenTX has differt features where i could get either the Model Name or the YAML file where the EdgeTX model configuration is stored.. to keep the code compatible, the model name is used.
+
+5. `Reversing a channel in my TX do not reverse the AS3X/SAFE reaction.` Correct, the chanel stick direction and the Gyro direction are two separate things.
+
+    5.1: First, you have setup your model so that the sticks and switches moves the surfaces in the right direction.
+ 
+    5.2: Go to the script, `Model Setup` and setup your wing type, tail type, and select the channel assigment for each surface. Leave the servo settings the same as the values in the TX to start.
+ 
+    5.3: Go to `Forward programming->Gyro Setting->Initial Setup` (New/factory reset), or `Forward programming->Gyro Setting->System Setup->Relearn Servo Settings` (not new). This will load your current Gyro servo settings into the plane's RX. This moves the current servo TX settings to the RX, so it is now in a known state.
+ 
+    5.4: Verify that the AS3X and SAFE reacts in the proper direction. You can use the Flight mode configured as "Safe Mode: Auto-Level" to see if it moves the surfaces in the right direction.  
+ 
+    5.5: If a surface don't move in the right direction, go to the `Model Setup->Gyro Channel Reverse` to reverse the Gyro on the channels needed, and do again the `Forward programming->Gyro Setting->System Setup->Relearn Servo Settings` to tranfer the new settings to the RX.
+
+    5.6: Specktrum TX always passes the TX servo reverse as the Gyro Reverse, but on many OpenTX/EdgeTX radios, the Rud/Ail are usually reversed by default compared to Specktrum. So far i don't think that i can use this as a rule, that is why the `Gyro Channel Reverse` page exist. 
+    
+
+
+---
+---
+
+# Changes and fixes 
+V0.56:
+
+1. Fix Tail-Type "Taileron" functionality that was not working. Also validated V-Tail and Delta wings.
+2. Added Taileron and two Rudder config (Many Freewing Jets like F18,F16, etc)
+3. Gyro-Reverse Screen now shows what is the channel/port used for (Ail, Ele, Rud, etc)
+4. COLOR ONLY: Gyro-Reverse Screen now shows what information that shared with the RX about each channel (Role, Slave, Reverse).
+5. NEW!! Initial version of Plane Setup for B&W radios
+
+V0.55a:
+1. Fix loading external messages file for OpenTX.
+   
+V0.55:
+1. Finally found where the TX reports to the RX how many channels is transmiting. The TX now reports itself as a 12ch radio instead of 6h. (DSM Multi-Module limit).  This fixes a few things:
+    
+    
+    a. Many places where you have to select channels > CH6 for Flight-Mode, Gains, Panic now works properly with the scroller. The radio is still validating that you are not selecting an invalid channel. For example, if you have an additional AIL on CH6, it will not allow you to use CH6 for FM or Gains.. it just move to the next valid one.
+
+    b. When setting up AIL/ELE on channels greater than CH6, on previous versions SAFE/AS3X was not moving them.. now they work up correctly.  Set them up in the first in CH1-CH10.  Why CH10?? Thats what fits on the reverse screen, otherwise, have to add more screens.
+
+    c. Some individual Gain channels was not allowing to setup on CH greater than CH6. Now is fixed.
+
+2. User Interface:
+    a. `RTN` Key now works as `Back` when the screen has a `Back`. Makes it easy for navigation.. Presing `RTN` on the main screen exists the tool.
+    b. Much faster refresh of the menus. Optimize the process of send/recive menu data from the RX.
+
+3. The TX now comunicates the SubTrim positions to the RX during `Relearn Servo Setting`. This changes the center of movement to one side or another. Really not much difference with small amounts of subtrim, previous versions where asuming subtrim of 0. When you have an extreame subtrim to one side, it was not moving simetrically.
+
+4. Support for FC6250HX (the one with separate RX).. Setup Swashplate type, RX orientation works properly.. This are menu options that the smaller version that comes in the
+Blade 230S did not have.
+
+
+V0.54:
+1. Fix a problem in the Attitude Trim page (`Gyro Settings->System Setup->SAFE/Panic Setup->Attitude Trim`). It was not saving the values after exiting the menu. This is to change what SAFE considers "Level" flying.
+2. Wings 2-Ail 2-Flaps had a bug on the 2nd flap.
+3. New Minimalistic script (`DsmFwdPrg_05_MIN.lua`): For radios with very low memory (FrSky QX7, RM Zorro, others). It can only change existing settings, but does not have the Plane Setup menus to setup a completly new plane.  In some radios, the very first time it runs (compile + run), it might give you a `not enouth memory` error.. try to run it again.
+4. External menu message file (DSMLIB/msg_fwdp_en.txt and MIN_msg_fwdp_en.txt).  Intial work to do localization and different languages.
+
+V0.53:
+1. Improved channel selection (Flight mode, Panic Channel, Gains Channel). Now during editing a channel, you can select any channel (>Ch4). Also, of you toggle the switch/channel it will populate the screen.
+2. Support for smaller screens (128x64) in B&W. The problem with this older radios is memory. In some, it does not have enouth memory to load the additional DSMLIB libraries.
+3. Fix formatting problem with some TX channel names who could affect the screen.. for example, rud channel should show "Ch4/rud", but shows "Ch4ud" because /r is for right justify formatting on messages. Now the formatting is only if it appears at the end of the message.
+
+V0.52:
+1. Menus to be able to configure Plane in a similar way as Spektrum Radio (v0.52)
+2. Make "Gyro Settings"->"Initial Setup" works (Tested on AR631,AR637xx with PLANE type of aircraft)
+3. Properly reset and restart after initial configuration and SAFE changes.
+4. Write Log of the conversation between RX/TX. To be used for debugging a problem is reported. 
+5. Provide a simulation of RX to do GUI development in Companion, and understand patterns of how the data is organized.
+
+
+# Tested Hardware
+- AR631/AR637xx
+- FC6250HX (Blade 230S V2 Helicopter; FC+RX in one, mini version)
+- FC6250HX (Separate RX.. use only V55 or newer of this tool)
+- AR636 (Blade 230S V1 Heli firmware 4.40)
+
+- Radiomaster TX16S  (All versions)
+
+Please report if you have tested it with other receivers to allow us to update the documentation. Code should work up to 10 channels for the main surfaces (Ail/Ele/etc).  All Spektrum RX are internally 20 channels, so you can use Ch7 for Flight Mode even if your RX is only 6 channels (See common Questions)
+
+
+# Messages Displayed in the GUI
+
+If in a screen you get text that looks like `Unknown_XX` (ex: Unknown_D3), that message has not been setup in the script in english. If you can determine what the proper message is,  you can send us a message to be added to the library.
+The `XX` represents a Hex Number (0..9,A..F)  message ID. 
+
+
+### Version 0.53 and older: 
+If you want to fix it in your local copy, all messages are towards the end in the file `SCRIPT\TOOS\DSMLIB\DsmFwPrgLib.lua`. Messages for Headers are stored in `Text` and messages for Options are stored in `List_Text`.  Lua scripts are text files, and can be edited with Notepad or equivalent.
+
+Portion of DsmFwPrgLib.lua:
+
+    Text[0x0097] = "Factory Reset"
+    Text[0x0098] = "Factory Reset" -- FC6250HX: Title
+    Text[0x0099] = "Advanced Setup"
+    Text[0x009A] = "Capture Failsafe Positions"
+    Text[0x009C] = "Custom Failsafe"
+
+    Text[0x009F] = "Save & Reset RX"  -- TODO: Find the Proper Spektrum Value ??
+
+    Text[0x00A5] = "First Time Setup"
+    Text[0x00AA] = "Capture Gyro Gains"
+    Text[0x00AD] = "Gain Channel Select"
+
+    -- Safe mode options, Inhibit + the values 
+    local safeModeOptions = {0x0003,0x00B0,0x00B1}  -- inh (gap), "Self-Level/Angle Dem, Envelope
+    List_Text[0x00B0] = "Self-Level/Angle Dem"
+    List_Text[0x00B1] = "Envelope"
+
+For example, if you get `Unknown_9D` in the GUI and your now that it should say **NEW Text**, you can edit the lua script to look like this:
+
+    Text[0x009A] = "Capture Failsafe Positions"
+    Text[0x009C] = "Custom Failsafe"
+
+    Text[0x009D] = "NEW Text" -- NEW Text added for AR98xx
+
+    Text[0x009F] = "Save & Reset RX"  -- TODO: Find the proper Spektrum text
+
+### Version 0.54 and newer:
+The menu messages are stored in DSMLIB/msg_fwdp_en.txt (For english). Just add the message there. MIN_msg_fwdp_en.txt has shorter messages overrides for screens who are smaller (for minimalistic 128x64 version).   The reference to the message file is at the file `/DSMLIB/DsmFwPrgLib.lua` if you want to change to use another language.
+
+    T |0x0097|Factory Reset
+    LT|0x00B0|Self-Level/Angle Dem
+    LT|0x00B1|Envelope
+
+
+# LOG File
+
+The log file of the last use of the script is located at `/LOGS/dsm_log.txt`. **It is overridden on every start to avoid filling up the SD card**. So if you want to keep it, copy or rename it before starting the script again. (it can be renamed in the TX by browsing the SD card)
+
+The log is human readable. The first number is the number of seconds since the start, and then what is the current state of the Library, and what has been sent and received. The info in the log can be easily used to create a new simulation for that RX in the future.
+
+Example Log:
+
+    5.340 WAIT_CMD: DSM_GotoMenu(0x1010,LastSelectedLine=0)
+    5.350 MENU_TITLE: SEND DSM_getMenu(MenuId=0x1010 LastSelectedLine=0)
+    5.440 MENU_TITLE: RESPONSE Menu: M[Id=0x1010 P=0x0 N=0x0 B=0x1000 Text="Gyro settings"[0xF9]]
+    5.490 MENU_LINES: SEND DSM_getFirstMenuLine(MenuId=0x1010)
+    5.590 MENU_LINES: RESPONSE MenuLine: L[#0 T=M VId=0x1011 Text="AS3X Settings"[0x1DD]   MId=0x1010 ]
+    5.640 MENU_LINES: SEND DSM_getNextLine(MenuId=0x1010,LastLine=0)
+    5.740 MENU_LINES: RESPONSE MenuLine: L[#1 T=M VId=0x1019 Text="SAFE Settings"[0x1E2]   MId=0x1010 ]
+    5.790 MENU_LINES: SEND DSM_getNextLine(MenuId=0x1010,LastLine=1)
+    5.850 MENU_LINES: RESPONSE MenuLine: L[#2 T=M VId=0x1021 Text="F-Mode Setup"[0x87]   MId=0x1010 ]
+    5.910 MENU_LINES: SEND DSM_getNextLine(MenuId=0x1010,LastLine=2)
+    5.970 MENU_LINES: RESPONSE MenuLine: L[#3 T=M VId=0x1022 Text="System Setup"[0x86]   MId=0x1010 ]
+    6.020 MENU_LINES: SEND DSM_getNextLine(MenuId=0x1010,LastLine=3
+
+# Validation of data by the RX
+
+The RX validates the data. if you change to an invalid channel or do a invalid number range, the RX will change it at the end of editing the field.
+
+---
+# Version 0.53
+- Improve Channel selection in menus
+- Support smaller screens 128x64 in the black/white mode.
+
+# Version 0.52
+- Fix Reversing of Servos
+- Properly detect Multimodule Ch settings AETR 
+---
+
+# Version 0.51  (volunteer testing version, not for production)
+- New Screens to Configure Model (Wing Type/Tail Tail, etc)
+- Finally got understanding that the previous unknown 0x05 lines are to send Model/Servo data to RX.
+- Fix use of AR636B (Firmware version 4.40.0 for Blade 230 heli, is the only one with Forward Programming)
+- Aircraft types:  Tested With Plane type only.. Glider and other in progress
+
+### Known Problems:
+- 4-Servo Wing type (Dual Ail/Tail) in planes give conflicting servo assignments by defaults.. Solution choose your own Ch.
+- Glider, Heli, Drone: Still in development. In glider, only a few wing type works.. needs to restrict menu options for the only valid one.
+
+
+# Version 0.5
+
+- Make the code more readable and understandable
+- Separate the DSM Forwards Programming logic from the GUI
+- Log the communication with the RX on a /LOGS/dsm_log.txt to allow to debug it easier 
+	and see the exchange of data between the RX/TX
+- Created a black/white Text only version with only Key/Roller Inputs
+- Created a nicer GUI for EdgeTX touch screen color Radios
+- RX simulation for GUI development:  turn on `SIMULATION_ON=true` in the beginning of the lua file
+- Test it on AR631, AR637xx, FC6250HX (Helicopter)
+
+### Some settings that can change (top of Lua file):
+    SIMULATION_ON = false   -- FALSE: hide similation menu (DEFAULT), TRUE: show RX simulation menu 
+	DEBUG_ON = 1           -- 0=NO DEBUG, 1=HIGH LEVEL 2=LOW LEVEL   (Debug logged into the /LOGS/dsm_log.txt)
+	USE_SPECKTRUM_COLORS = true -- true: Use spectrum colors, false: use theme colors (default on OpenTX, OpenTX handle colors different) 
+
+
+### Known Problems:
+1. **Incorrect List Value Options:** Some Menu List line (`LINE_TYPE.LIST_MENU1` or `L_m1` in logs), the range (min/max) of valid values seems to be incorrect, but the RX corrects the values.
+in the MINimalistic version, the RX is doing all the range validation, and will show invalid options temporarilly. In an Spektrum radio, it happens so fast, that you don't notice it, but in LUA scripts who are slower, you can see it in the screen. 
+In the COLOR version, The code has hardcoded the valid ranges to avoid this problem.
+
+2. Glider/Heli/Drone wing types not ready.
+
+For Helicopter, use airplane normal wing and normal tail
+
+
+# Version 0.2
+Original Version from Pascal Langer
+ 

Lua_scripts/MultiChan.txt

@@ -119,9 +119,10 @@
 49,0,KF606,KF606,1,Trim
 49,1,KF606,MIG320,1,Trim,LED
 49,2,KF606,ZCZ50,1,Trim,UNK
-9,0,KN,WLToys,0,DRate,THold,IdleUp,Gyro,Ttrim,Atrim,Etrim
-9,1,KN,Feilun,0,DRate,THold,IdleUp,Gyro,Ttrim,Atrim,Etrim
-73,0,Kyosho,Std,0,CH5,CH6,CH7,CH8,CH9,CH10,CH11,CH12,CH13,CH14
+9,0,KN,WLToys,0,DRate,THold,IdleUp,Gyro,Ttrim,Atrim,Etrim,Rtrim,Hover
+9,1,KN,Feilun,0,DRate,THold,IdleUp,Gyro,Ttrim,Atrim,Etrim,Rtrim,Hover
+73,0,Kyosho,FHSS,0,CH5,CH6,CH7,CH8,CH9,CH10,CH11,CH12,CH13,CH14
+73,1,Kyosho,Hype,0,CH5,CH6
 18,0,MJXQ,WHL08,1,Flip,LED,Pict,Video,HLess,RTH,AuFlip,Pan,Tilt,Rate
 18,1,MJXQ,X600,1,Flip,LED,Pict,Video,HLess,RTH,AuFlip,Pan,Tilt,Rate
 18,2,MJXQ,X800,1,Flip,LED,Pict,Video,HLess,RTH,AuFlip,Pan,Tilt,Rate
@@ -155,6 +156,7 @@
 74,0,RadioLink,Surface,0,CH5,CH6,CH7,CH8,FS_CH1,FS_CH2,FS_CH3,FS_CH4,FS_CH5,FS_CH6,FS_CH7,FS_CH8
 74,1,RadioLink,Air,0,CH5,CH6,CH7,CH8,FS_CH1,FS_CH2,FS_CH3,FS_CH4,FS_CH5,FS_CH6,FS_CH7,FS_CH8
 74,2,RadioLink,DumboRC,0,CH5,CH6,CH7,CH8,FS_CH1,FS_CH2,FS_CH3,FS_CH4,FS_CH5,FS_CH6,FS_CH7,FS_CH8
+74,3,RadioLink,RC4G,0,CH5,FS_CH1,FS_CH2,FS_CH3,FS_CH4
 76,0,Realacc,R11,1,Flip,Light,Calib,HLess,RTH,UNK
 50,0,Redpine,Fast,0,sCH5,sCH6,sCH7,sCH8,sCH9,sCH10,sCH11,sCH12,sCH13,sCH14,sCH15,sCH16
 50,1,Redpine,Slow,0,sCH5,sCH6,sCH7,sCH8,sCH9,sCH10,sCH11,sCH12,sCH13,sCH14,sCH15,sCH16
@@ -168,7 +170,6 @@
 11,4,SLT,MR100,0,Rates,n-a,CH7,CH8,Mode,Flip,Video,Pict
 10,0,Symax,Std,1,Flip,Rates,Pict,Video,HLess
 10,1,Symax,X5C,1,Flip,Rates,Pict,Video,HLess
-61,0,Tiger,Std,1,Flip,Light
 43,0,Traxxas,6519,0
 5,0,V2x2,Std,1,Flip,Light,Pict,Video,HLess,CalX,CalY
 5,1,V2x2,JXD506,1,Flip,Light,Pict,Video,HLess,StaSto,Emerg,Cam_UD
@@ -185,7 +186,8 @@
 30,4,WK2x01,W6HEL,0,Gear,Col,Gyro
 30,5,WK2x01,W6HEL_I,0,Gear,Col,Gyro
 62,0,XK,X450,1,FMode,TakeOf,Emerg,3D_6G,Pict,Video
-62,1,XK,X420,1,FMode,TakeOf,Emerg,3D_6G,Pict,Video
+62,1,XK,X420,1,FMode,TakeOf,Emerg,3D_6G,Pict,Video,Flip,Light
+62,2,XK,Cars,0,FMode,TakeOf,Emerg,3D_6G,Pict,Video,Flip,Light
 8,0,YD717,Std,1,Flip,Light,Pict,Video,HLess
 8,1,YD717,SkyWlkr,1,Flip,Light,Pict,Video,HLess
 8,2,YD717,Simax4,1,Flip,Light,Pict,Video,HLess
@@ -198,7 +200,7 @@
 81,0,E010r5,E010r5,1,Flip,LED,CALIB,HLess,RTH,GLIDE
 82,0,LOLI,Std,0,CH5,CH6,CH7,CH8,1SwSePpPw,2SwSePw,3SwSe,4SwSe,5SwSeSb,6SwSe,7SwSePw,8SwSe
 83,0,E129,E129,1,TakLan,EmStop,TrimA,TrimE,TrimR
-83,1,E129,C186,1,TakLan,EmStop,TrimA,TrimE,TrimR
+83,1,E129,C186,1,TakLan,EmStop,TrimA,TrimE,TrimR,Loop,Flip
 84,0,JOYSWAY,Std,0
 85,0,E016H,Std,1,Stop,Flip,n-a,HLess,RTH
 87,0,IKEA
@@ -209,3 +211,6 @@
 92,0,MT99xx2,PA18,0,MODE,FLIP,RTH
 93,0,Kyosho2,KT-17,0
 94,0,Scorpio
+95,0,Bluefly,HP100,0,CH5,CH6,CH7,CH8
+96,0,BumbleB
+97,0,SGF22,Std,1,Mode,Flip,LED,Pict,Video

Lua_scripts/MultiConfig.lua

@@ -135,11 +135,15 @@ local function Config_Draw_Edit( event )
         Edit = 0
       elseif event == EVT_VIRTUAL_PREV then
       -- Change value
+        if Menu_value[Edit_pos] > 0 then
           Menu_value[Edit_pos] = Menu_value[Edit_pos] - 1
+        end
       elseif event == EVT_VIRTUAL_NEXT then
       -- Change value
+        if Menu_value[Edit_pos] < 255 then
           Menu_value[Edit_pos] = Menu_value[Edit_pos] + 1
         end
+      end
       --Blink
       Blink = Blink + 1
       if Blink > 30 then
@@ -319,9 +323,6 @@ local function Config_Draw_Menu()
       --Read line from buffer
       for i = 0, 20-1, 1 do
         value=multiBuffer( line*20+13+i )
-        if value == 0 then
-          break   -- end of line
-        end
         if value > 0x80 and Menu[line].field_type == 0 then
         -- Read field type
           Menu[line].field_type = bitand(value, 0xF0)
@@ -334,6 +335,9 @@ local function Config_Draw_Menu()
         else
           if Menu[line].field_type == 0 then
           -- Text
+          if value == 0 then
+            break   -- end of line
+          end
             Menu[line].text = Menu[line].text .. string.char(value)
           else
           -- Menu specific fields

Lua_scripts/README.md

@@ -58,15 +58,11 @@ This is the Graupner HoTT adapted version of the Model Locator script using RSSI
 
 The OpenTX sensor "RSSI" is populated by the individual OpenTX telemetry protocol implementations and returns a value from 0..100 (percent) originating from the early FrSky implementation. It turns out that FrSky did not really provide a genuine signal strength indicator in units of dbm but a link quality indicator in 0..100%. With Graupner HoTT the link quality indicator is not a good basis for the model locator as it is very non-linear and doesn't change much with distance. Using the Graupner HoTT telemetry sensor "Rssi" which is a true signal strength indicator serves the purpose of locating a model much better as it varies much more with distance.
 
-## DSM Forward Programming
+## DSM Tools for EdgeTX and OpenTx
 
-This is a work in progress. It's available for color(+touch) and B&W screens.
+Collection of EdgeTx/OpenTX Tools to use with Spektrum Receivers including forward programming. Located on the radio SD card under \SCRIPTS\TOOLS, make sure to copy the DSMLIB folder!
 
-Work on OpenTX and EdgeTX. Located on the radio SD card under \SCRIPTS\TOOLS, make sure to copy the DSMLIB folder along with DSM FwdPrg_05_Color.lua or DSM FwdPrg_05_BW.lua.
-
-[![DSM Forward Programming](https://img.youtube.com/vi/sjIaDw5j9nE/0.jpg)](https://www.youtube.com/watch?v=sjIaDw5j9nE)
-
-If some text appears as Unknown_xxx, please report xxx and what the exact text display should be.
+Frank is maintaining these awesome tools, check out his [repository](https://github.com/frankiearzu/DSMTools). Feel free to ask questions or open issues there.
 
 ## DSM PID Flight log gain parameters for Blade micros
 

Multiprotocol/A7105_SPI.ino

@@ -418,10 +418,10 @@ void A7105_Init(void)
 			#ifdef KYOSHO_A7105_INO
 				if(protocol==PROTO_KYOSHO)
 				{
-					if(sub_protocol==KYOSHO_FHSS)
-						A7105_Regs=(uint8_t*)KYOSHO_A7105_regs;
-					else
+					if(sub_protocol==KYOSHO_HYPE)
 						A7105_Regs=(uint8_t*)KYOSHO_HYPE_A7105_regs;
+					else //FHSS && SYNCRO
+						A7105_Regs=(uint8_t*)KYOSHO_A7105_regs;
 				}
 			#endif
 		}
@@ -446,7 +446,7 @@ void A7105_Init(void)
 	}
 	A7105_Strobe(A7105_STANDBY);
 
-	if(protocol==PROTO_KYOSHO && sub_protocol==KYOSHO_FHSS)
+	if(protocol==PROTO_KYOSHO && sub_protocol!=KYOSHO_HYPE)
 	{//strange calibration...
 		//IF Filter Bank Calibration
 		A7105_WriteReg(A7105_02_CALC,0x0F);

Multiprotocol/BUMBLEB_ccnrf.ino

@@ -0,0 +1,196 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#if defined(BUMBLEB_CCNRF_INO)
+
+#include "iface_xn297.h"
+
+#define FORCE_BUMBLEB_ORIGINAL_ID
+#define BUMBLEB_TELEM_DEBUG
+
+#define BUMBLEB_PACKET_PERIOD	10200
+#define BUMBLEB_RF_BIND_CHANNEL	42
+#define BUMBLEB_RF_NUM_CHANNELS	2
+#define BUMBLEB_PAYLOAD_SIZE	7
+
+static void __attribute__((unused)) BUMBLEB_send_packet()
+{
+	packet[6] = 0x00;
+	if(IS_BIND_IN_PROGRESS)
+	{
+		packet[0] = rx_tx_addr[0];
+		packet[1] = rx_tx_addr[1];
+		packet[2] = 0x54;			 //???
+		packet[3] = 0x58;			 //???
+		hopping_frequency_no ^= 0x01;
+		packet[4] = hopping_frequency[hopping_frequency_no];
+	}
+	else
+	{
+		//hopping frequency
+		XN297_Hopping(hopping_frequency_no);
+		hopping_frequency_no ^= 0x01;
+		packet[0] = 0x20
+					|GET_FLAG(CH6_SW,0x80);				// High rate
+		packet[1] = convert_channel_8b_limit_deadband(AILERON,0xBF,0xA0,0x81,40);	// Aileron: Max values:BD..A0..82
+		if(packet[1] < 0xA0)
+			packet[1] = 0x20 - packet[1];				// Reverse low part of aileron
+		packet[2] = convert_channel_8b(CH5)>>2;			// 01..20..3F
+		if(CH7_SW)										// Drive trim from aileron
+		{
+			uint8_t ch=convert_channel_8b(AILERON);
+			if(ch > 0x5A && ch < 0x80-0x07)
+				packet[2] = ch - 0x5A;
+			else if(ch < 0x5A)
+			{
+				if(ch < 0x5A-0x20)
+					packet[2] = 0;
+				else
+					packet[2] = ch - (0x5A-0x20);
+			}
+			else if(packet[1] == 0x89)
+				packet[2] = 0x20;
+			else if(ch > 0xA5)
+			{
+				if(ch > 0xA9+0x1F)
+					packet[2] = 0x3F;
+				else
+					packet[2] = ch - 0x89;
+			}
+			else if(ch > 0xA5-0x1F)
+				packet[2] = ch - (0xA5-0x1F-0x20);
+		}
+		else
+			packet[2] = convert_channel_8b(CH5)>>2;		// 01..20..3F
+		packet[3] = convert_channel_8b(THROTTLE)>>2;	// 00..3F
+		packet[4] = hopping_frequency[hopping_frequency_no];
+	}
+
+	packet[5] = packet[0];
+	for(uint8_t i=1;i<BUMBLEB_PAYLOAD_SIZE-2;i++)
+		packet[5] += packet[i];
+
+	#if 0
+		debug("P:");
+		for(uint8_t i=0;i<BUMBLEB_PAYLOAD_SIZE;i++)
+			debug(" %02X", packet[i]);
+		debugln("");
+	#endif
+
+	XN297_SetPower();									// Set tx_power
+	XN297_SetFreqOffset();								// Set frequency offset
+	XN297_SetTxRxMode(TX_EN);
+	XN297_WritePayload(packet, BUMBLEB_PAYLOAD_SIZE);
+}
+
+static void __attribute__((unused)) BUMBLEB_RF_init()
+{
+	//Config CC2500
+	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_250K);
+	XN297_SetTXAddr((uint8_t*)"\x55\x55\x55\x55\x55", 5);
+	XN297_HoppingCalib(BUMBLEB_RF_NUM_CHANNELS);		// Calibrate all channels
+	XN297_RFChannel(BUMBLEB_RF_BIND_CHANNEL);			// Set bind channel
+	XN297_SetRXAddr(rx_tx_addr, BUMBLEB_PAYLOAD_SIZE);
+}
+
+static void __attribute__((unused)) BUMBLEB_initialize_txid()
+{
+	calc_fh_channels(BUMBLEB_RF_NUM_CHANNELS);
+	rx_tx_addr[0] = rx_tx_addr[2];
+	rx_tx_addr[1] = rx_tx_addr[3];
+	#ifdef FORCE_BUMBLEB_ORIGINAL_ID
+		rx_tx_addr[0] = 0x33;
+		rx_tx_addr[1] = 0x65;
+		hopping_frequency[0] = 2;
+		hopping_frequency[1] = 40;
+	#endif
+	rx_tx_addr[2] = rx_tx_addr[3] = rx_tx_addr[4] = 0x55;
+}
+
+enum {
+	BUMBLEB_BIND		= 0x00,
+	BUMBLEB_BINDRX		= 0x01,
+	BUMBLEB_DATA		= 0x02,
+};
+
+#define BUMBLEB_WRITE_TIME 850
+
+uint16_t BUMBLEB_callback()
+{
+	bool rx;
+	switch(phase)
+	{
+		case BUMBLEB_BIND:
+			rx = XN297_IsRX();				// Needed for the NRF24L01 since otherwise the bit gets cleared
+
+			BUMBLEB_send_packet();
+
+			if( rx )
+			{ // a packet has been received
+				#ifdef BUMBLEB_TELEM_DEBUG
+					debug("RX :");
+				#endif
+				if(XN297_ReadPayload(packet_in, BUMBLEB_PAYLOAD_SIZE))
+				{ // packet with good CRC
+					#ifdef BUMBLEB_TELEM_DEBUG
+						debug("OK :");
+						for(uint8_t i=0;i<BUMBLEB_PAYLOAD_SIZE;i++)
+							debug(" %02X",packet_in[i]);
+					#endif
+					// packet_in = 4F 71 55 52 58 61 AA
+					rx_tx_addr[2] = packet_in[0];
+					rx_tx_addr[3] = packet_in[1];
+					//rx_tx_addr[4] = packet_in[2];	// to test with other planes...
+					XN297_SetTXAddr(rx_tx_addr, 5);
+					BIND_DONE;
+					phase = BUMBLEB_DATA;
+					break;
+				}
+			}
+			phase++;
+			return BUMBLEB_WRITE_TIME;
+		case BUMBLEB_BINDRX:
+			{
+				uint16_t start=(uint16_t)micros();
+				while ((uint16_t)((uint16_t)micros()-(uint16_t)start) < 500)
+				{
+					if(XN297_IsPacketSent())
+						break;
+				}
+			}
+			XN297_SetTxRxMode(RX_EN);
+			phase = BUMBLEB_BIND;
+			return BUMBLEB_PACKET_PERIOD-BUMBLEB_WRITE_TIME;
+		case BUMBLEB_DATA:
+			#ifdef MULTI_SYNC
+				telemetry_set_input_sync(BUMBLEB_PACKET_PERIOD);
+			#endif
+			BUMBLEB_send_packet();
+			break;
+	}
+	return BUMBLEB_PACKET_PERIOD;
+}
+
+void BUMBLEB_init()
+{
+	BUMBLEB_initialize_txid();
+	BUMBLEB_RF_init();
+	hopping_frequency_no = 0;
+	
+	BIND_IN_PROGRESS;	// autobind protocol
+	phase = BUMBLEB_BIND;
+}
+
+#endif

Multiprotocol/Bluefly_ccnrf.ino

@@ -0,0 +1,118 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+// compatible with BLUEFLY HP100
+
+#if defined(BLUEFLY_CCNRF_INO)
+
+#include "iface_nrf250k.h"
+
+#define BLUEFLY_PACKET_PERIOD		6000
+#define BLUEFLY_PACKET_SIZE			12
+#define BLUEFLY_RF_BIND_CHANNEL		81
+#define BLUEFLY_NUM_RF_CHANNELS		15
+#define BLUEFLY_BIND_COUNT			800
+#define BLUEFLY_TXID_SIZE			5
+
+static void __attribute__((unused)) BLUEFLY_send_packet()
+{
+	if(IS_BIND_IN_PROGRESS)
+	{
+		memset(packet, 0x55, BLUEFLY_PACKET_SIZE);
+		memcpy(packet, rx_tx_addr, BLUEFLY_TXID_SIZE);
+		packet[5] = hopping_frequency[0];
+	}
+	else
+	{
+		NRF250K_Hopping(hopping_frequency_no);
+		hopping_frequency_no++;
+		if(hopping_frequency_no >= BLUEFLY_NUM_RF_CHANNELS);
+			hopping_frequency_no = 0;
+
+		packet[8] = packet[9] = 0;
+		for(uint8_t i=0; i<8 ; i++)
+		{
+			uint16_t ch = convert_channel_16b_limit(CH_AETR[i], 0, 1000);
+			packet[ i] = ch;
+			ch &= 0x300;
+			ch >>= 2;
+			packet[8 + (i>3?0:1)] = (packet[8 + (i>3?0:1)] >> 2) | ch;
+		}
+		// Checksum
+		uint8_t l, h, t;
+		l = h = 0xff;
+		for (uint8_t i=0; i<10; ++i)
+		{
+			h ^= packet[i];
+			h ^= h >> 4;
+			t = h;
+			h = l;
+			l = t;
+			t = (l<<4) | (l>>4);
+			h ^= ((t<<2) | (t>>6)) & 0x1f;
+			h ^= t & 0xf0;
+			l ^= ((t<<1) | (t>>7)) & 0xe0;
+		}
+		packet[10] = h; 
+		packet[11] = l;
+	}
+	
+	NRF250K_WritePayload(packet, BLUEFLY_PACKET_SIZE);
+	NRF250K_SetPower();				// Set tx_power
+	NRF250K_SetFreqOffset();		// Set frequency offset
+}
+
+static void __attribute__((unused)) BLUEFLY_RF_init()
+{
+	NRF250K_Init();
+	NRF250K_SetTXAddr((uint8_t *)"\x32\xAA\x45\x45\x78", BLUEFLY_TXID_SIZE);	// BLUEFLY Bind address
+	NRF250K_HoppingCalib(BLUEFLY_NUM_RF_CHANNELS);								// Calibrate all channels
+	NRF250K_RFChannel(BLUEFLY_RF_BIND_CHANNEL);									// Set bind channel
+}
+
+static void __attribute__((unused)) BLUEFLY_initialize_txid()
+{
+    uint8_t start = (rx_tx_addr[3] % 47) + 2;
+	for(uint8_t i=0;i<BLUEFLY_NUM_RF_CHANNELS;i++)
+		hopping_frequency[i] = start + i*2;
+	hopping_frequency_no=0;
+}
+
+uint16_t BLUEFLY_callback()
+{
+	#ifdef MULTI_SYNC
+		telemetry_set_input_sync(BLUEFLY_PACKET_PERIOD);
+	#endif
+	if(bind_counter)
+	{
+		bind_counter--;
+		if (bind_counter == 0)
+		{
+			BIND_DONE;
+			NRF250K_SetTXAddr(rx_tx_addr, BLUEFLY_TXID_SIZE);
+		}
+	}
+	BLUEFLY_send_packet();
+	return	BLUEFLY_PACKET_PERIOD;
+}
+
+void BLUEFLY_init(void)
+{
+	BLUEFLY_initialize_txid();
+	BLUEFLY_RF_init();
+
+	bind_counter = IS_BIND_IN_PROGRESS ? BLUEFLY_BIND_COUNT : 1;
+}
+
+#endif

Multiprotocol/CYRF6936_SPI.ino

@@ -195,11 +195,11 @@ void CYRF_ConfigSOPCode(const uint8_t *sopcodes)
 	CYRF_WriteRegisterMulti(CYRF_22_SOP_CODE, sopcodes, 8);
 }
 
-void CYRF_ConfigDataCode(const uint8_t *datacodes, uint8_t len)
+void CYRF_ConfigDataCode(const uint8_t *datacodes)
 {
 	//NOTE: This can also be implemented as:
-	//for(i = 0; i < len; i++) WriteRegister)0x23, datacodes[i];
-	CYRF_WriteRegisterMulti(CYRF_23_DATA_CODE, datacodes, len);
+	//for(i = 0; i < 16; i++) WriteRegister)0x23, datacodes[i];
+	CYRF_WriteRegisterMulti(CYRF_23_DATA_CODE, datacodes, 16);
 }
 
 void CYRF_WritePreamble(uint32_t preamble)
@@ -298,7 +298,7 @@ void CYRF_FindBestChannels(uint8_t *channels, uint8_t len, uint8_t minspace, uin
 	CYRF_WriteRegister(CYRF_29_RX_ABORT, 0x00);		// Clear abort RX
 }
 
-#if defined(DEVO_CYRF6936_INO) || defined(J6PRO_CYRF6936_INO)
+#if defined(DEVO_CYRF6936_INO) || defined(J6PRO_CYRF6936_INO) || defined(TRAXXAS_CYRF6936_INO)
 const uint8_t PROGMEM DEVO_j6pro_sopcodes[][8] = {
     /* Note these are in order transmitted (LSB 1st) */
     {0x3C, 0x37, 0xCC, 0x91, 0xE2, 0xF8, 0xCC, 0x91},
@@ -311,7 +311,7 @@ const uint8_t PROGMEM DEVO_j6pro_sopcodes[][8] = {
     {0xB9, 0x8E, 0x19, 0x74, 0x6F, 0x65, 0x18, 0x74},
     {0xDF, 0xB1, 0xC0, 0x49, 0x62, 0xDF, 0xC1, 0x49},
     {0x97, 0xE5, 0x14, 0x72, 0x7F, 0x1A, 0x14, 0x72},
-#if defined(J6PRO_CYRF6936_INO)
+#if defined(J6PRO_CYRF6936_INO) || defined(TRAXXAS_CYRF6936_INO)
     {0x82, 0xC7, 0x90, 0x36, 0x21, 0x03, 0xFF, 0x17},
     {0xE2, 0xF8, 0xCC, 0x91, 0x3C, 0x37, 0xCC, 0x91}, //Note: the '03' was '9E' in the Cypress recommended table
     {0xAD, 0x39, 0xA2, 0x0F, 0x9B, 0xC5, 0xA1, 0x0F}, //The following are the same as the 1st 8 above,
@@ -322,14 +322,22 @@ const uint8_t PROGMEM DEVO_j6pro_sopcodes[][8] = {
     {0x9E, 0x82, 0xDC, 0x3C, 0xA1, 0x78, 0xDC, 0x3C},
     {0x6F, 0x65, 0x18, 0x74, 0xB9, 0x8E, 0x19, 0x74},
 #endif
+#if defined(TRAXXAS_CYRF6936_INO)
+    {0x62, 0xDF, 0xC1, 0x49, 0xDF, 0xB1, 0xC0, 0x49},
+#endif
 };
 #endif
 
 static void __attribute__((unused)) CYRF_PROGMEM_ConfigSOPCode(const uint8_t *data)
 {
 	uint8_t code[8];
+	//debug("SOP:");
 	for(uint8_t i=0;i<8;i++)
+	{
 		code[i]=pgm_read_byte_near(&data[i]);
+		//debug(" %02X",code[i]);
+	}
+	//debugln("");
 	CYRF_ConfigSOPCode(code);
 }
 

Multiprotocol/DSM.ino

@@ -4,9 +4,45 @@
 
 uint8_t sop_col;
 
-const uint8_t PROGMEM DSM_pncodes[5][9][8] = {
+const uint8_t PROGMEM DSM_pncodes[][8] = {
 	/* Note these are in order transmitted (LSB 1st) */
-	{ /* Row 0 */
+	/* Row 1 */
+		/* Col 0 */ {0x83, 0xF7, 0xA8, 0x2D, 0x7A, 0x44, 0x64, 0xD3},
+		/* Col 1 */ {0x3F, 0x2C, 0x4E, 0xAA, 0x71, 0x48, 0x7A, 0xC9},
+		/* Col 2 */ {0x17, 0xFF, 0x9E, 0x21, 0x36, 0x90, 0xC7, 0x82},
+		/* Col 3 */ {0xBC, 0x5D, 0x9A, 0x5B, 0xEE, 0x7F, 0x42, 0xEB},
+		/* Col 4 */ {0x24, 0xF5, 0xDD, 0xF8, 0x7A, 0x77, 0x74, 0xE7},
+		/* Col 5 */ {0x3D, 0x70, 0x7C, 0x94, 0xDC, 0x84, 0xAD, 0x95},
+		/* Col 6 */ {0x1E, 0x6A, 0xF0, 0x37, 0x52, 0x7B, 0x11, 0xD4},
+		/* Col 7 */ {0x62, 0xF5, 0x2B, 0xAA, 0xFC, 0x33, 0xBF, 0xAF},
+	/* Row 2 */
+		/* Col 0 */ {0x40, 0x56, 0x32, 0xD9, 0x0F, 0xD9, 0x5D, 0x97},
+		/* Col 1 */ {0x8E, 0x4A, 0xD0, 0xA9, 0xA7, 0xFF, 0x20, 0xCA},
+		/* Col 2 */ {0x4C, 0x97, 0x9D, 0xBF, 0xB8, 0x3D, 0xB5, 0xBE},
+		/* Col 3 */ {0x0C, 0x5D, 0x24, 0x30, 0x9F, 0xCA, 0x6D, 0xBD},
+		/* Col 4 */ {0x50, 0x14, 0x33, 0xDE, 0xF1, 0x78, 0x95, 0xAD},
+		/* Col 5 */ {0x0C, 0x3C, 0xFA, 0xF9, 0xF0, 0xF2, 0x10, 0xC9},
+		/* Col 6 */ {0xF4, 0xDA, 0x06, 0xDB, 0xBF, 0x4E, 0x6F, 0xB3},
+		/* Col 7 */ {0x9E, 0x08, 0xD1, 0xAE, 0x59, 0x5E, 0xE8, 0xF0},
+	/* Row 3 */
+		/* Col 0 */ {0xC0, 0x90, 0x8F, 0xBB, 0x7C, 0x8E, 0x2B, 0x8E},
+		/* Col 1 */ {0x80, 0x69, 0x26, 0x80, 0x08, 0xF8, 0x49, 0xE7},
+		/* Col 2 */ {0x7D, 0x2D, 0x49, 0x54, 0xD0, 0x80, 0x40, 0xC1},
+		/* Col 3 */ {0xB6, 0xF2, 0xE6, 0x1B, 0x80, 0x5A, 0x36, 0xB4},
+		/* Col 4 */ {0x42, 0xAE, 0x9C, 0x1C, 0xDA, 0x67, 0x05, 0xF6},
+		/* Col 5 */ {0x9B, 0x75, 0xF7, 0xE0, 0x14, 0x8D, 0xB5, 0x80},
+		/* Col 6 */ {0xBF, 0x54, 0x98, 0xB9, 0xB7, 0x30, 0x5A, 0x88},
+		/* Col 7 */ {0x35, 0xD1, 0xFC, 0x97, 0x23, 0xD4, 0xC9, 0x88},
+	/* Row 4 */
+		/* Col 0 */ {0xE1, 0xD6, 0x31, 0x26, 0x5F, 0xBD, 0x40, 0x93}, // Wrong values used by Orange TX/RX Row 3 Col 8: {0x88, 0xE1, 0xD6, 0x31, 0x26, 0x5F, 0xBD, 0x40}
+		/* Col 1 */ {0xDC, 0x68, 0x08, 0x99, 0x97, 0xAE, 0xAF, 0x8C},
+		/* Col 2 */ {0xC3, 0x0E, 0x01, 0x16, 0x0E, 0x32, 0x06, 0xBA},
+		/* Col 3 */ {0xE0, 0x83, 0x01, 0xFA, 0xAB, 0x3E, 0x8F, 0xAC},
+		/* Col 4 */ {0x5C, 0xD5, 0x9C, 0xB8, 0x46, 0x9C, 0x7D, 0x84},
+		/* Col 5 */ {0xF1, 0xC6, 0xFE, 0x5C, 0x9D, 0xA5, 0x4F, 0xB7},
+		/* Col 6 */ {0x58, 0xB5, 0xB3, 0xDD, 0x0E, 0x28, 0xF1, 0xB0},
+		/* Col 7 */ {0x5F, 0x30, 0x3B, 0x56, 0x96, 0x45, 0xF4, 0xA1},
+	/* Row 0 */
 		/* Col 0 */ {0x03, 0xBC, 0x6E, 0x8A, 0xEF, 0xBD, 0xFE, 0xF8},
 		/* Col 1 */ {0x88, 0x17, 0x13, 0x3B, 0x2D, 0xBF, 0x06, 0xD6},
 		/* Col 2 */ {0xF1, 0x94, 0x30, 0x21, 0xA1, 0x1C, 0x88, 0xA9},
@@ -16,59 +52,15 @@ const uint8_t PROGMEM DSM_pncodes[5][9][8] = {
 		/* Col 6 */ {0xEF, 0x03, 0x95, 0x89, 0xB4, 0x71, 0x61, 0x9D},
 		/* Col 7 */ {0x40, 0xBA, 0x97, 0xD5, 0x86, 0x4F, 0xCC, 0xD1},
 		/* Col 8 */ {0xD7, 0xA1, 0x54, 0xB1, 0x5E, 0x89, 0xAE, 0x86}
-	},
-	{ /* Row 1 */
-		/* Col 0 */ {0x83, 0xF7, 0xA8, 0x2D, 0x7A, 0x44, 0x64, 0xD3},
-		/* Col 1 */ {0x3F, 0x2C, 0x4E, 0xAA, 0x71, 0x48, 0x7A, 0xC9},
-		/* Col 2 */ {0x17, 0xFF, 0x9E, 0x21, 0x36, 0x90, 0xC7, 0x82},
-		/* Col 3 */ {0xBC, 0x5D, 0x9A, 0x5B, 0xEE, 0x7F, 0x42, 0xEB},
-		/* Col 4 */ {0x24, 0xF5, 0xDD, 0xF8, 0x7A, 0x77, 0x74, 0xE7},
-		/* Col 5 */ {0x3D, 0x70, 0x7C, 0x94, 0xDC, 0x84, 0xAD, 0x95},
-		/* Col 6 */ {0x1E, 0x6A, 0xF0, 0x37, 0x52, 0x7B, 0x11, 0xD4},
-		/* Col 7 */ {0x62, 0xF5, 0x2B, 0xAA, 0xFC, 0x33, 0xBF, 0xAF},
-		/* Col 8 */ {0x40, 0x56, 0x32, 0xD9, 0x0F, 0xD9, 0x5D, 0x97}
-	},
-	{ /* Row 2 */
-		/* Col 0 */ {0x40, 0x56, 0x32, 0xD9, 0x0F, 0xD9, 0x5D, 0x97},
-		/* Col 1 */ {0x8E, 0x4A, 0xD0, 0xA9, 0xA7, 0xFF, 0x20, 0xCA},
-		/* Col 2 */ {0x4C, 0x97, 0x9D, 0xBF, 0xB8, 0x3D, 0xB5, 0xBE},
-		/* Col 3 */ {0x0C, 0x5D, 0x24, 0x30, 0x9F, 0xCA, 0x6D, 0xBD},
-		/* Col 4 */ {0x50, 0x14, 0x33, 0xDE, 0xF1, 0x78, 0x95, 0xAD},
-		/* Col 5 */ {0x0C, 0x3C, 0xFA, 0xF9, 0xF0, 0xF2, 0x10, 0xC9},
-		/* Col 6 */ {0xF4, 0xDA, 0x06, 0xDB, 0xBF, 0x4E, 0x6F, 0xB3},
-		/* Col 7 */ {0x9E, 0x08, 0xD1, 0xAE, 0x59, 0x5E, 0xE8, 0xF0},
-		/* Col 8 */ {0xC0, 0x90, 0x8F, 0xBB, 0x7C, 0x8E, 0x2B, 0x8E}
-	},
-	{ /* Row 3 */
-		/* Col 0 */ {0xC0, 0x90, 0x8F, 0xBB, 0x7C, 0x8E, 0x2B, 0x8E},
-		/* Col 1 */ {0x80, 0x69, 0x26, 0x80, 0x08, 0xF8, 0x49, 0xE7},
-		/* Col 2 */ {0x7D, 0x2D, 0x49, 0x54, 0xD0, 0x80, 0x40, 0xC1},
-		/* Col 3 */ {0xB6, 0xF2, 0xE6, 0x1B, 0x80, 0x5A, 0x36, 0xB4},
-		/* Col 4 */ {0x42, 0xAE, 0x9C, 0x1C, 0xDA, 0x67, 0x05, 0xF6},
-		/* Col 5 */ {0x9B, 0x75, 0xF7, 0xE0, 0x14, 0x8D, 0xB5, 0x80},
-		/* Col 6 */ {0xBF, 0x54, 0x98, 0xB9, 0xB7, 0x30, 0x5A, 0x88},
-		/* Col 7 */ {0x35, 0xD1, 0xFC, 0x97, 0x23, 0xD4, 0xC9, 0x88},
-		/* Col 8 */ {0xE1, 0xD6, 0x31, 0x26, 0x5F, 0xBD, 0x40, 0x93}
-// Wrong values used by Orange TX/RX
-//		/* Col 8 */ {0x88, 0xE1, 0xD6, 0x31, 0x26, 0x5F, 0xBD, 0x40}
-	},
-	{ /* Row 4 */
-		/* Col 0 */ {0xE1, 0xD6, 0x31, 0x26, 0x5F, 0xBD, 0x40, 0x93},
-		/* Col 1 */ {0xDC, 0x68, 0x08, 0x99, 0x97, 0xAE, 0xAF, 0x8C},
-		/* Col 2 */ {0xC3, 0x0E, 0x01, 0x16, 0x0E, 0x32, 0x06, 0xBA},
-		/* Col 3 */ {0xE0, 0x83, 0x01, 0xFA, 0xAB, 0x3E, 0x8F, 0xAC},
-		/* Col 4 */ {0x5C, 0xD5, 0x9C, 0xB8, 0x46, 0x9C, 0x7D, 0x84},
-		/* Col 5 */ {0xF1, 0xC6, 0xFE, 0x5C, 0x9D, 0xA5, 0x4F, 0xB7},
-		/* Col 6 */ {0x58, 0xB5, 0xB3, 0xDD, 0x0E, 0x28, 0xF1, 0xB0},
-		/* Col 7 */ {0x5F, 0x30, 0x3B, 0x56, 0x96, 0x45, 0xF4, 0xA1},
-		/* Col 8 */ {0x03, 0xBC, 0x6E, 0x8A, 0xEF, 0xBD, 0xFE, 0xF8}
-	},
 };
 
-static void __attribute__((unused)) DSM_read_code(uint8_t *buf, uint8_t row, uint8_t col, uint8_t len)
+static void __attribute__((unused)) DSM_read_code(uint8_t *buf, uint8_t row, uint8_t col)
 {
-	for(uint8_t i=0;i<len;i++)
-		buf[i]=pgm_read_byte_near( &DSM_pncodes[row][col][i] );
+	row--;
+	if(row>4)
+		row = 4;
+	for(uint8_t i=0;i<8;i++)
+		buf[i]=pgm_read_byte_near( &DSM_pncodes[row*8+col][i] );
 }
 
 const uint8_t PROGMEM DSM_init_vals[][2] = {
@@ -137,11 +129,11 @@ static void __attribute__((unused)) DSM_set_sop_data_crc(bool ch2, bool dsmx)
 		debug_time();
 		debug(" crc:%04X,row:%d,col:%d,rf:%02X",(~seed)&0xffff,pn_row,sop_col,hopping_frequency[hopping_frequency_no]);
 	#endif
-	DSM_read_code(code,pn_row,sop_col,8);					// pn_row between 0 and 4, sop_col between 1 and 7
+	DSM_read_code(code,pn_row,sop_col);						// pn_row between 0 and 4, sop_col between 0 and 7
 	CYRF_ConfigSOPCode(code);
-	DSM_read_code(code,pn_row,7 - sop_col,8);				// 7-sop_col between 0 and 6
-	DSM_read_code(code+8,pn_row,7 - sop_col + 1,8);			// 7-sop_col+1 between 1 and 7
-	CYRF_ConfigDataCode(code, 16);
+	DSM_read_code(code,pn_row,7 - sop_col);					// 7-sop_col between 0 and 7
+	DSM_read_code(code+8,pn_row,7 - sop_col + 1);			// 7-sop_col+1 between 1 and 8
+	CYRF_ConfigDataCode(code);
 
 	CYRF_ConfigRFChannel(hopping_frequency[hopping_frequency_no]);
 	hopping_frequency_no++;

Multiprotocol/DSM_Rx_cyrf6936.ino

@@ -39,8 +39,8 @@ static void __attribute__((unused)) DSM_RX_RF_init()
 	{
 		//64 SDR Mode is configured so only the 8 first values are needed but need to write 16 values...
 		uint8_t code[16];
-		DSM_read_code(code,0,8,8);
-		CYRF_ConfigDataCode(code, 16);
+		DSM_read_code(code,0,8);
+		CYRF_ConfigDataCode(code);
 		CYRF_ConfigRFChannel(1);
 		CYRF_SetTxRxMode(RX_EN);									// Force end state read
 		CYRF_WriteRegister(CYRF_05_RX_CTRL, 0x83);					// Prepare to receive
@@ -277,7 +277,7 @@ uint16_t DSM_RX_callback()
 						eeprom_write_byte((EE_ADDR)temp, DSM_rx_type);
 						CYRF_WriteRegister(CYRF_29_RX_ABORT, 0x20);	// Abort RX operation
 						CYRF_SetTxRxMode(TX_EN);					// Force end state TX
-						CYRF_ConfigDataCode((const uint8_t *)"\x98\x88\x1B\xE4\x30\x79\x03\x84", 16);
+						CYRF_ConfigDataCode((const uint8_t *)"\x98\x88\x1B\xE4\x30\x79\x03\x84");
 						CYRF_WriteRegister(CYRF_29_RX_ABORT, 0x00);	// Clear abort RX
 						DSM_RX_build_bind_packet();
 						bind_counter=500;

Multiprotocol/DSM_cyrf6936.ino

@@ -18,16 +18,22 @@
 #include "iface_cyrf6936.h"
 
 //#define DSM_DEBUG_FWD_PGM
-
+//#define DEBUG_BIND  1
 //#define DSM_GR300
 
 #define CLONE_BIT_MASK 0x20 
 
 #define DSM_BIND_CHANNEL 0x0d //13 This can be any odd channel
 
-//During binding we will send BIND_COUNT/2 packets
+//During binding we will send BIND_COUNT packets
 //One packet each 10msec
-#define DSM_BIND_COUNT 300
+//
+// Most RXs seems to work properly with a long BIND send count (3s): Spektrum, OrangeRX. 
+// Lemon-RX G2s seems to have a timeout waiting for the channel to get quiet after the 
+// first good BIND packet.. If using 3s (300), Lemon-RX will not transmit the BIND-Response packet. 
+
+#define DSM_BIND_COUNT             180  // About 1.8s
+#define DSM_BIND_COUNT_READ        600  // About 4.2s of waiting for Response
 
 enum {
 	DSM_BIND_WRITE=0,
@@ -118,8 +124,8 @@ static void __attribute__((unused)) DSM_initialize_bind_phase()
 	CYRF_ConfigRFChannel(DSM_BIND_CHANNEL); //This seems to be random?
 	//64 SDR Mode is configured so only the 8 first values are needed but need to write 16 values...
 	uint8_t code[16];
-	DSM_read_code(code,0,8,8);
-	CYRF_ConfigDataCode(code, 16);
+	DSM_read_code(code,0,8);
+	CYRF_ConfigDataCode(code);
 	DSM_build_bind_packet();
 }
 
@@ -292,11 +298,14 @@ uint16_t DSM_callback()
 			return 10000;
 	#if defined DSM_TELEMETRY
 		case DSM_BIND_CHECK:
-			//64 SDR Mode is configured so only the 8 first values are needed but we need to write 16 values...
-			CYRF_ConfigDataCode((const uint8_t *)"\x98\x88\x1B\xE4\x30\x79\x03\x84", 16);
+      #if DEBUG_BIND
+        debugln("Bind Check");
+      #endif
+      //64 SDR Mode is configured so only the 8 first values are needed
+      CYRF_ConfigDataCode((const uint8_t *)"\x98\x88\x1B\xE4\x30\x79\x03\x84");
 			CYRF_SetTxRxMode(RX_EN);							//Receive mode
 			CYRF_WriteRegister(CYRF_05_RX_CTRL, 0x87);			//Prepare to receive
-			bind_counter=2*DSM_BIND_COUNT;						//Timeout of 4.2s if no packet received
+			bind_counter=DSM_BIND_COUNT_READ; //Timeout of 4.2s if no packet received
 			phase++;											// change from BIND_CHECK to BIND_READ
 			return 2000;
 		case DSM_BIND_READ:
@@ -312,10 +321,12 @@ uint16_t DSM_callback()
 					CYRF_ReadDataPacketLen(packet_in+1, 10);
 					if(DSM_Check_RX_packet())
 					{
+						#if DEBUG_BIND
   						  debug("Bind");
   						  for(uint8_t i=0;i<10;i++)
   							debug(" %02X",packet_in[i+1]);
   						  debugln("");
+						#endif
 						packet_in[0]=0x80;
 						packet_in[6]&=0x0F;						// It looks like there is a flag 0x40 being added by some receivers
 						if(packet_in[6]>12) packet_in[6]=12;
@@ -340,6 +351,9 @@ uint16_t DSM_callback()
 				}
 			if( --bind_counter == 0 )
 			{ // Exit if no answer has been received for some time
+        #if DEBUG_BIND
+          debugln("Bind Read TIMEOUT");
+        #endif
 				phase++;										// DSM_CHANSEL
 				return 7000 ;
 			}
@@ -539,19 +553,23 @@ void DSM_init()
 			if(eeprom_read_byte((EE_ADDR)DSM_CLONE_EEPROM_OFFSET+4)==0xF0)
 			{
 				//read cloned ID from EEPROM
-				debugln("Using cloned ID");
 				uint16_t temp = DSM_CLONE_EEPROM_OFFSET;
 				for(uint8_t i=0;i<4;i++)
 					cyrfmfg_id[i] = eeprom_read_byte((EE_ADDR)temp++);
+        #if DEBUG_BIND
+          debugln("Using cloned ID");  
   				debug("Clone ID=")
   				for(uint8_t i=0;i<4;i++)
   					debug("%02x ", cyrfmfg_id[i]);
   				debugln("");
+          #endif
 			}
 			else
 			{
 				SUB_PROTO_INVALID;
+        #if DEBUG_BIND
 				  debugln("No valid cloned ID");
+        #endif
 			}
 		}
 		else
@@ -610,9 +628,12 @@ void DSM_init()
 		DSM_initialize_bind_phase();		
 		phase = DSM_BIND_WRITE;
     bind_counter=DSM_BIND_COUNT;
+    #if DEBUG_BIND
+      debugln("Bind Started: write count=%d",bind_counter);
+    #endif
 	}
 	else
-		phase = DSM_CHANSEL;//
+		phase = DSM_CHANSEL;
 }
 
 #endif

Multiprotocol/E129_cyrf6936.ino

@@ -53,7 +53,9 @@ static void __attribute__((unused)) E129_build_data_packet()
 			packet[15] = bit_reverse(rx_tx_addr[0]);
 			packet[16] = bit_reverse(rx_tx_addr[1]);
 		}
-		//packet[ 3] = 0x00;							// E129 Mode: short press=0x20->0x00->0x20->..., long press=0x10->0x30->0x10->... => C186 throttle trim is doing the same:up=short press and down=long press
+		packet[ 3] = GET_FLAG(CH10_SW, 0x40)			// C159 loop flight 0x40, flag 0x04 is also set on this heli
+				   | GET_FLAG(CH11_SW, 0x08);			// C129V2 flip
+														// Other flags in packet[3] => E129 Mode: short press=0x20->0x00->0x20->..., long press=0x10->0x30->0x10->... => C186 throttle trim is doing the same:up=short press and down=long press
 		packet[ 4] = GET_FLAG(CH5_SW,  0x20)			// Take off/Land 0x20
 				   | GET_FLAG(CH6_SW,  0x04);			// Emergency stop 0x04
 		//Channels and trims
@@ -80,12 +82,10 @@ static void __attribute__((unused)) E129_build_data_packet()
 		packet[12] = val;								// channel (0x000...0x200...0x3FF)
 	}
 	//Check
-	if(sub_protocol == E129_E129)
-		packet[packet_length-2] = packet[0] + packet[1];
-	else
-		packet[packet_length-2] = 0x24 + packet[0] + (packet[1]&0x03);	// ??
-	for(uint8_t i=2;i<packet_length-2;i++)
+	for(uint8_t i=0;i<packet_length-2;i++)
 		packet[packet_length-2] += packet[i];
+	if(sub_protocol == E129_C186)
+		packet[packet_length-2] -= 0x80;
 
 	RF2500_BuildPayload(packet);
 }

Multiprotocol/Hisky_nrf24l01.ino

@@ -66,8 +66,10 @@ static void __attribute__((unused)) HISKY_RF_init()
 	NRF24L01_WriteRegisterMulti(NRF24L01_0A_RX_ADDR_P0, rx_tx_addr, 5);
 	NRF24L01_WriteRegisterMulti(NRF24L01_10_TX_ADDR, rx_tx_addr, 5);
 	NRF24L01_WriteReg(NRF24L01_11_RX_PW_P0, 10);		// payload size = 10
+	#ifndef MULTI_AIR
 	if(sub_protocol==HK310)
 		NRF24L01_SetBitrate(NRF24L01_BR_250K);			// 250Kbps
+	#endif
 }
 
 // HiSky channel sequence: AILE  ELEV  THRO  RUDD  GEAR  PITCH, channel data value is from 0 to 1000
@@ -92,6 +94,13 @@ static void __attribute__((unused)) HISKY_build_ch_data()
 uint16_t HISKY_callback()
 {
 	phase++;
+	#ifdef MULTI_AIR
+		if(sub_protocol==HK310)
+		{
+			SUB_PROTO_INVALID;
+			return 10000;
+		}
+	#else
 	if(sub_protocol==HK310)
 		switch(phase)
 		{
@@ -132,6 +141,7 @@ uint16_t HISKY_callback()
 				phase=8;
 				break;
 		}
+	#endif
 	switch(phase)
 	{
 		case 1:
@@ -195,6 +205,7 @@ uint16_t HISKY_callback()
 static void __attribute__((unused)) HISKY_initialize_tx_id()
 {
 	//Generate frequency hopping table	
+	#ifndef MULTI_AIR
 	if(sub_protocol==HK310)
 	{
 		// for HiSky surface protocol, the transmitter always generates hop channels in sequential order. 
@@ -204,10 +215,11 @@ static void __attribute__((unused)) HISKY_initialize_tx_id()
 			hopping_frequency[i]=hopping_frequency_no++;	// Sequential order hop channels...
 	}
 	else
-		calc_fh_channels(HISKY_FREQUENCE_NUM);
+	#endif
 		// HiSky air protocol uses TX id as an address for nRF24L01, and uses frequency hopping sequence
 		// which does not depend on this id and is passed explicitly in binding sequence. So we are free
 		// to generate this sequence as we wish. It should be in the range [02..77]
+		calc_fh_channels(HISKY_FREQUENCE_NUM);
 }
 
 void HISKY_init()

Multiprotocol/J6Pro_cyrf6936.ino

@@ -36,7 +36,7 @@ enum PktState {
 };
 
 const uint8_t PROGMEM j6pro_bind_sop_code[] = {0x62, 0xdf, 0xc1, 0x49, 0xdf, 0xb1, 0xc0, 0x49};
-//const uint8_t j6pro_data_code[] = {0x02, 0xf9, 0x93, 0x97, 0x02, 0xfa, 0x5c, 0xe3, 0x01, 0x2b, 0xf1, 0xdb, 0x01, 0x32, 0xbe, 0x6f}; // unneeded since this is the default table after a reset
+const uint8_t j6pro_data_code[] = {0x02, 0xf9, 0x93, 0x97, 0x02, 0xfa, 0x5c, 0xe3, 0x01, 0x2b, 0xf1, 0xdb, 0x01, 0x32, 0xbe, 0x6f}; // unneeded since this is the default table after a reset
 
 static void __attribute__((unused)) j6pro_build_bind_packet()
 {
@@ -84,7 +84,9 @@ static void __attribute__((unused)) j6pro_cyrf_init()
     CYRF_WriteRegister(CYRF_10_FRAMING_CFG, 0xee);
     CYRF_WriteRegister(CYRF_1F_TX_OVERRIDE, 0x00);
     CYRF_WriteRegister(CYRF_1E_RX_OVERRIDE, 0x00);
-    //CYRF_ConfigDataCode(j6pro_data_code, 16);
+    
+	//Same as default reset but issues if not configured...
+	CYRF_ConfigDataCode(j6pro_data_code);
     CYRF_WritePreamble(0x333302);
 
     CYRF_GetMfgData(cyrfmfg_id);

Multiprotocol/KN_nrf24l01.ino

@@ -63,7 +63,7 @@ enum {
 	KN_FLAG_DR     = 0x01, // Dual Rate: 1 - full range
 	KN_FLAG_TH     = 0x02, // Throttle Hold: 1 - hold
 	KN_FLAG_IDLEUP = 0x04, // Idle up: 1 - 3D
-	KN_FLAG_RES1   = 0x08,
+	KN_FLAG_RES1   = 0x08, // HoverDebugging
 	KN_FLAG_RES2   = 0x10,
 	KN_FLAG_RES3   = 0x20,
 	KN_FLAG_GYRO3  = 0x40, // 0 - 6G mode, 1 - 3G mode
@@ -141,19 +141,13 @@ static void __attribute__((unused)) kn_update_packet_control_data()
 	packet[8]  = convert_channel_16b_limit(CH9,0,200); // 0x64; // T
 	packet[9]  = convert_channel_16b_limit(CH10,0,200); // 0x64; // A
 	packet[10] = convert_channel_16b_limit(CH11,0,200); // 0x64; // E
-	packet[11] = 0x64; // R
+	packet[11] = convert_channel_16b_limit(CH12,0,200); // 0x64; // R
 
-	flags=0;
-	if (CH5_SW)
-		flags = KN_FLAG_DR;
-	if (CH6_SW)
-		flags |= KN_FLAG_TH;
-	if (CH7_SW)
-		flags |= KN_FLAG_IDLEUP;
-	if (CH8_SW)
-		flags |= KN_FLAG_GYRO3;
-
-	packet[12] = flags;
+	packet[12] = GET_FLAG(CH5_SW,  KN_FLAG_DR)
+				|GET_FLAG(CH6_SW,  KN_FLAG_TH)
+				|GET_FLAG(CH7_SW,  KN_FLAG_IDLEUP)
+				|GET_FLAG(CH8_SW,  KN_FLAG_GYRO3)
+				|GET_FLAG(CH13_SW, KN_FLAG_RES1);	//Hover debugging
 
 	packet[13] = 0x00;
 	if(sub_protocol==WLTOYS)

Multiprotocol/Kyosho_a7105.ino

@@ -19,10 +19,12 @@
 
 //#define KYOSHO_FORCE_ID_FHSS
 //#define KYOSHO_FORCE_ID_HYPE
+//#define KYOSHO_FORCE_ID_SYNCRO
 
 //Kyosho constants & variables
 #define KYOSHO_BIND_COUNT 2500
 
+#ifndef MULTI_AIR
 static void __attribute__((unused)) KYOSHO_send_packet()
 {
 	//ID
@@ -42,8 +44,9 @@ static void __attribute__((unused)) KYOSHO_send_packet()
 		//RF table
 		for(uint8_t i=0; i<16;i++)
 			packet[i+11]=hopping_frequency[i+(packet[9]<<4)];
-		//unknwon
-		packet[27]  = 0x05;
+		//TX type
+		packet[27]  = (bind_counter & 0x40) ? 0x05:0x07;	// FHSS is 5 and Syncro is 7
+		//Unknown
 		packet[28]  = 0x00;
 		memset(packet+29,0xFF,8);
 		//frequency hop during bind
@@ -55,13 +58,23 @@ static void __attribute__((unused)) KYOSHO_send_packet()
 	else
 	{
 		packet[ 0]  = 0x58;						// normal packet
-		//14 channels: steering, throttle, ...
-		for(uint8_t i = 0; i < 14; i++)
+		//FHSS  14 channels: steering, throttle, ...
+		//Syncro 6 channels: steering, throttle, ...
+		for(uint8_t i = 0; i < 14; i++) 		//needed? i < (sub_protocol==KYOSHO_FHSS?14:6); i++)
 		{
 			uint16_t temp = convert_channel_ppm(i);
 			packet[ 9 + i*2] = temp&0xFF;		// low byte of servo timing(1000-2000us)
 			packet[10 + i*2] = (temp>>8)&0xFF;	// high byte of servo timing(1000-2000us)
 		}
+		// if(sub_protocol==KYOSHO_SYNCRO) 	// needed?
+		// {
+			// memcpy(&packet[21],&hopping_frequency[11],6);
+			// packet[27]  = 0x07;
+			// packet[28]  = 0x00;
+			// memset(packet+29,0xFF,8);
+			// packet[34] = 0x0F;
+			// packet[36] = 0x0F;
+		// }
 		rf_ch_num=hopping_frequency[hopping_frequency_no];
 		hopping_frequency_no++;
 		packet[34] |= (hopping_frequency_no&0x0F)<<4;
@@ -76,6 +89,7 @@ static void __attribute__((unused)) KYOSHO_send_packet()
 	#endif
 	A7105_WriteData(37, rf_ch_num);
 }
+#endif //MULTI_AIR
 
 static void __attribute__((unused)) KYOSHO_hype_send_packet()
 {
@@ -150,10 +164,14 @@ uint16_t KYOSHO_callback()
 			telemetry_set_input_sync(packet_period);
 		#endif
 	}
-	if(sub_protocol==KYOSHO_FHSS)
-		KYOSHO_send_packet();
-	else//HYPE
+	if(sub_protocol==KYOSHO_HYPE)
 		KYOSHO_hype_send_packet();
+	else //FHSS && SYNCRO
+	#ifndef MULTI_AIR
+		KYOSHO_send_packet();
+	#else
+		SUB_PROTO_INVALID;
+	#endif
 	return packet_period;
 }
 
@@ -162,7 +180,7 @@ void KYOSHO_init()
 	A7105_Init();
 
 	// compute channels from ID
-	calc_fh_channels(sub_protocol==KYOSHO_FHSS?32:15);
+	calc_fh_channels(sub_protocol==KYOSHO_HYPE?15:32);
 	hopping_frequency_no=0;
 
 	#ifdef KYOSHO_FORCE_ID_FHSS
@@ -172,6 +190,13 @@ void KYOSHO_init()
 			memcpy(hopping_frequency,"\x29\x4C\x67\x92\x31\x1C\x77\x18\x23\x6E\x81\x5C\x8F\x5A\x51\x94\x7A\x12\x45\x6C\x7F\x1E\x0D\x88\x63\x8C\x4F\x37\x26\x61\x2C\x8A",32);
 		}
 	#endif
+	#ifdef KYOSHO_FORCE_ID_SYNCRO
+		if(sub_protocol==KYOSHO_FHSS)
+		{
+			memcpy(rx_tx_addr,"\x00\xC2\x24\x00",4);
+			memcpy(hopping_frequency,"\x73\x12\x7D\x88\x63\x4A\x8D\x60\x57\x16\x5D\x8B\x25\x53\x6E\x3C\x41\x70\x20\x83\x2A\x19\x94\x2F\x91\x4C\x47\x36\x78\x10\x5A\x31",32);
+		}
+	#endif
 	if(sub_protocol==KYOSHO_HYPE)
 	{
 		MProtocol_id &= 0x00FF00FF;

Multiprotocol/Losi_cyrf6936.ino

@@ -17,25 +17,63 @@
 
 #include "iface_cyrf6936.h"
 
-#define LOSI_FORCE_ID
+//#define LOSI_FORCE_ID
 
-const uint8_t PROGMEM LOSI_bind_sop_code[] = {0x62, 0xdf, 0xc1, 0x49, 0xdf, 0xb1, 0xc0, 0x49};
-const uint8_t LOSI_data_code[][16] = {
-	{ 0xD7, 0xA1, 0x54, 0xB1, 0x5E, 0x89, 0xAE, 0x86, 0xC9, 0x2C, 0x06, 0x93, 0x86, 0xB9, 0x9E, 0xD7 }, //bind
-/*	{ 0xE1, 0xD6, 0x31, 0x26, 0x5F, 0xBD, 0x40, 0x93, 0xDC, 0x68, 0x08, 0x99, 0x97, 0xAE, 0xAF, 0x8C },
-	{ 0xDC, 0x68, 0x08, 0x99, 0x97, 0xAE, 0xAF, 0x8C, 0xC3, 0x0E, 0x01, 0x16, 0x0E, 0x32, 0x06, 0xBA },
-	{ 0xC3, 0x0E, 0x01, 0x16, 0x0E, 0x32, 0x06, 0xBA, 0xE0, 0x83, 0x01, 0xFA, 0xAB, 0x3E, 0x8F, 0xAC },
-	{ 0xE0, 0x83, 0x01, 0xFA, 0xAB, 0x3E, 0x8F, 0xAC, 0x5C, 0xD5, 0x9C, 0xB8, 0x46, 0x9C, 0x7D, 0x84 },
-	{ 0x5C, 0xD5, 0x9C, 0xB8, 0x46, 0x9C, 0x7D, 0x84, 0xF1, 0xC6, 0xFE, 0x5C, 0x9D, 0xA5, 0x4F, 0xB7 },
-	{ 0xF1, 0xC6, 0xFE, 0x5C, 0x9D, 0xA5, 0x4F, 0xB7, 0x58, 0xB5, 0xB3, 0xDD, 0x0E, 0x28, 0xF1, 0xB0 },
-	{ 0x58, 0xB5, 0xB3, 0xDD, 0x0E, 0x28, 0xF1, 0xB0, 0x5F, 0x30, 0x3B, 0x56, 0x96, 0x45, 0xF4, 0xA1 },*/
-	{ 0x5F, 0x30, 0x3B, 0x56, 0x96, 0x45, 0xF4, 0xA1, 0x03, 0xBC, 0x6E, 0x8A, 0xEF, 0xBD, 0xFE, 0xF8 }	//normal
-};
+/* Using DSM.ino data codes since they are the same
+const uint8_t LOSI_data_code[][8] = {
+	//(Freq-1)%5=0
+	{ 0x83, 0xF7, 0xA8, 0x2D, 0x7A, 0x44, 0x64, 0xD3 },
+	{ 0x3F, 0x2C, 0x4E, 0xAA, 0x71, 0x48, 0x7A, 0xC9 },
+	{ 0x17, 0xFF, 0x9E, 0x21, 0x36, 0x90, 0xC7, 0x82 },
+	{ 0xBC, 0x5D, 0x9A, 0x5B, 0xEE, 0x7F, 0x42, 0xEB },
+	{ 0x24, 0xF5, 0xDD, 0xF8, 0x7A, 0x77, 0x74, 0xE7 },
+	{ 0x3D, 0x70, 0x7C, 0x94, 0xDC, 0x84, 0xAD, 0x95 },
+	{ 0x1E, 0x6A, 0xF0, 0x37, 0x52, 0x7B, 0x11, 0xD4 },
+	{ 0x62, 0xF5, 0x2B, 0xAA, 0xFC, 0x33, 0xBF, 0xAF },
+	//(Freq-1)%5=1
+	{ 0x40, 0x56, 0x32, 0xD9, 0x0F, 0xD9, 0x5D, 0x97 },
+	{ 0x8E, 0x4A, 0xD0, 0xA9, 0xA7, 0xFF, 0x20, 0xCA },
+	{ 0x4C, 0x97, 0x9D, 0xBF, 0xB8, 0x3D, 0xB5, 0xBE },
+	{ 0x0C, 0x5D, 0x24, 0x30, 0x9F, 0xCA, 0x6D, 0xBD },
+	{ 0x50, 0x14, 0x33, 0xDE, 0xF1, 0x78, 0x95, 0xAD },
+	{ 0x0C, 0x3C, 0xFA, 0xF9, 0xF0, 0xF2, 0x10, 0xC9 },
+	{ 0xF4, 0xDA, 0x06, 0xDB, 0xBF, 0x4E, 0x6F, 0xB3 },
+	{ 0x9E, 0x08, 0xD1, 0xAE, 0x59, 0x5E, 0xE8, 0xF0 },
+	//(Freq-1)%5=2
+	{ 0xC0, 0x90, 0x8F, 0xBB, 0x7C, 0x8E, 0x2B, 0x8E },
+	{ 0x80, 0x69, 0x26, 0x80, 0x08, 0xF8, 0x49, 0xE7 },
+	{ 0x7D, 0x2D, 0x49, 0x54, 0xD0, 0x80, 0x40, 0xC1 },
+	{ 0xB6, 0xF2, 0xE6, 0x1B, 0x80, 0x5A, 0x36, 0xB4 },
+	{ 0x42, 0xAE, 0x9C, 0x1C, 0xDA, 0x67, 0x05, 0xF6 },
+	{ 0x9B, 0x75, 0xF7, 0xE0, 0x14, 0x8D, 0xB5, 0x80 },
+	{ 0xBF, 0x54, 0x98, 0xB9, 0xB7, 0x30, 0x5A, 0x88 },
+	{ 0x35, 0xD1, 0xFC, 0x97, 0x23, 0xD4, 0xC9, 0x88 },
+	//(Freq-1)%5=3
+	{ 0xE1, 0xD6, 0x31, 0x26, 0x5F, 0xBD, 0x40, 0x93 },
+	{ 0xDC, 0x68, 0x08, 0x99, 0x97, 0xAE, 0xAF, 0x8C },
+	{ 0xC3, 0x0E, 0x01, 0x16, 0x0E, 0x32, 0x06, 0xBA },
+	{ 0xE0, 0x83, 0x01, 0xFA, 0xAB, 0x3E, 0x8F, 0xAC },
+	{ 0x5C, 0xD5, 0x9C, 0xB8, 0x46, 0x9C, 0x7D, 0x84 },
+	{ 0xF1, 0xC6, 0xFE, 0x5C, 0x9D, 0xA5, 0x4F, 0xB7 },
+	{ 0x58, 0xB5, 0xB3, 0xDD, 0x0E, 0x28, 0xF1, 0xB0 },
+	{ 0x5F, 0x30, 0x3B, 0x56, 0x96, 0x45, 0xF4, 0xA1 },
+	//(Freq-1)%5=4
+	{ 0x03, 0xBC, 0x6E, 0x8A, 0xEF, 0xBD, 0xFE, 0xF8 },
+	{ 0x88, 0x17, 0x13, 0x3B, 0x2D, 0xBF, 0x06, 0xD6 },
+	{ 0xF1, 0x94, 0x30, 0x21, 0xA1, 0x1C, 0x88, 0xA9 },
+	{ 0xD0, 0xD2, 0x8E, 0xBC, 0x82, 0x2F, 0xE3, 0xB4 },
+	{ 0x8C, 0xFA, 0x47, 0x9B, 0x83, 0xA5, 0x66, 0xD0 },
+	{ 0x07, 0xBD, 0x9F, 0x26, 0xC8, 0x31, 0x0F, 0xB8 },
+	{ 0xEF, 0x03, 0x95, 0x89, 0xB4, 0x71, 0x61, 0x9D },
+	{ 0x40, 0xBA, 0x97, 0xD5, 0x86, 0x4F, 0xCC, 0xD1 },
+	//Bind
+	{ 0xD7, 0xA1, 0x54, 0xB1, 0x5E, 0x89, 0xAE, 0x86 }
+};*/
 
 static uint16_t __attribute__((unused)) LOSI_check(uint16_t val)
 {
 	const uint8_t PROGMEM tab[] = { 0xF1, 0xDA, 0xB6, 0xC8 };
-	uint8_t res = 0x0B, tmp;
+	uint8_t res = crc8, tmp;
 	uint16_t calc = val>>2; 								// don't care about the 2 first bits
 	for(uint8_t i=0; i<5; i++)
 	{
@@ -56,8 +94,11 @@ static void __attribute__((unused)) LOSI_send_packet()
 	if(IS_BIND_IN_PROGRESS)
 	{
 		memcpy(&packet[4], rx_tx_addr, 4);
-		packet[8] = 0x05;               				    	// CRC?
-		packet[9] = 0x52;                   					// CRC?
+		crc = 0x0170;
+		for(uint8_t i=0; i < 8; i++)
+			crc += packet[i];
+		packet[8] = crc >> 8;
+		packet[9] = crc;
 	}
 	else
 	{
@@ -88,7 +129,7 @@ static void __attribute__((unused)) LOSI_cyrf_init()
 	CYRF_WriteRegister(CYRF_1B_TX_OFFSET_LSB, 0x55);
 	CYRF_WriteRegister(CYRF_1C_TX_OFFSET_MSB, 0x05);
 	//CYRF_WriteRegister(CYRF_0F_XACT_CFG, 0x24);
-	CYRF_SetPower(0x38);
+	CYRF_SetPower(0x38);									// 64 SDR mode -> 8 bytes data code
 	CYRF_WriteRegister(CYRF_12_DATA64_THOLD, 0x0A);
 	CYRF_WriteRegister(CYRF_39_ANALOG_CTRL, 0x01);
 	CYRF_WritePreamble(0x333304);
@@ -97,51 +138,80 @@ static void __attribute__((unused)) LOSI_cyrf_init()
 	CYRF_WriteRegister(CYRF_1F_TX_OVERRIDE, 0x04);			// No CRC
 	//CYRF_WriteRegister(CYRF_1E_RX_OVERRIDE, 0x14);
 	//CYRF_WriteRegister(CYRF_14_EOP_CTRL, 0x02);
+	uint8_t code[16];
+	DSM_read_code(code,0,8);								// Load bind data code by default
+	CYRF_ConfigDataCode(code);
 }
 
 uint16_t LOSI_callback()
 {
 	#ifdef MULTI_SYNC
-		telemetry_set_input_sync(19738);
+		telemetry_set_input_sync(packet_period);
 	#endif
-	LOSI_send_packet();
 	if(bind_counter)
 	{
 		bind_counter--;
 		if(bind_counter==0)
 		{
 			BIND_DONE;
-			CYRF_ConfigDataCode(LOSI_data_code[1], 16);			// Load normal data code
+			// Load normal data code
+			uint8_t code[16];
+			DSM_read_code(code,hopping_frequency[0] % 5,(rx_tx_addr[0] + rx_tx_addr[1] + rx_tx_addr[2]) % 8);
+			CYRF_ConfigDataCode(code);
+			packet_period = 19738;
 		}
-		return 8763;
 	}
-	return 19738;
+	LOSI_send_packet();
+	return packet_period;
 }
 
 void LOSI_init()
 {
 	LOSI_cyrf_init();
-	//CYRF_FindBestChannels(hopping_frequency, 1, 0, 0x13, 75);	// 75 is unknown since dump stops at 0x27, this routine resets the CRC Seed to 0
-	//CYRF_ConfigRFChannel(hopping_frequency[0] | 1);				// Only odd channels
+
+	CYRF_FindBestChannels(hopping_frequency, 1, 0, 0x07, 0x4F);	// 0x07 and 0x4F are unknown limits, this routine resets the CRC Seed to 0
+	hopping_frequency[0] |= 1;									// Only odd channels are used, integrated in CYRF code...
+
+	crc8 = 0;
+	crc8 = (uint16_t)LOSI_check(((rx_tx_addr[2]&0x0F) << 8) + rx_tx_addr[3]) >> 12;
 
 	#ifdef LOSI_FORCE_ID
+		/*	
 		rx_tx_addr[0] = 0x47;
 		rx_tx_addr[1] = 0x52;
 		rx_tx_addr[2] = 0xAE;
 		rx_tx_addr[3] = 0xAA;
-		CYRF_ConfigRFChannel(0x27);
+		crc8 = 0x0B;
+		num_ch = 0x07;
+		//Data codes for hopping_frequency[0] % 5
+		//{ 0x40, 0xBA, 0x97, 0xD5, 0x86, 0x4F, 0xCC, 0xD1, 0xD7, 0xA1, 0x54, 0xB1, 0x5E, 0x89, 0xAE, 0x86 },
+		//{ 0x62, 0xF5, 0x2B, 0xAA, 0xFC, 0x33, 0xBF, 0xAF, 0x40, 0x56, 0x32, 0xD9, 0x0F, 0xD9, 0x5D, 0x97 },
+		//{ 0x9E, 0x08, 0xD1, 0xAE, 0x59, 0x5E, 0xE8, 0xF0, 0xC0, 0x90, 0x8F, 0xBB, 0x7C, 0x8E, 0x2B, 0x8E },
+		//{ 0x35, 0xD1, 0xFC, 0x97, 0x23, 0xD4, 0xC9, 0x88, 0xE1, 0xD6, 0x31, 0x26, 0x5F, 0xBD, 0x40, 0x93 },
+		//{ 0x5F, 0x30, 0x3B, 0x56, 0x96, 0x45, 0xF4, 0xA1, 0x03, 0xBC, 0x6E, 0x8A, 0xEF, 0xBD, 0xFE, 0xF8 }
+		*/
+		rx_tx_addr[0] = 0x56;
+		rx_tx_addr[1] = 0x52;
+		rx_tx_addr[2] = 0x22;
+		rx_tx_addr[3] = 0x8A;
+		crc8 = 0x0F;
+		num_ch = 0x02;
+		//Data codes for hopping_frequency[0] % 5
+		//{ 0xF1, 0x94, 0x30, 0x21, 0xA1, 0x1C, 0x88, 0xA9, 0xD0, 0xD2, 0x8E, 0xBC, 0x82, 0x2F, 0xE3, 0xB4 },
+		//{ 0x17, 0xFF, 0x9E, 0x21, 0x36, 0x90, 0xC7, 0x82, 0xBC, 0x5D, 0x9A, 0x5B, 0xEE, 0x7F, 0x42, 0xEB },
+		//{ 0x4C, 0x97, 0x9D, 0xBF, 0xB8, 0x3D, 0xB5, 0xBE, 0x0C, 0x5D, 0x24, 0x30, 0x9F, 0xCA, 0x6D, 0xBD },
+		//{ 0x7D, 0x2D, 0x49, 0x54, 0xD0, 0x80, 0x40, 0xC1, 0xB6, 0xF2, 0xE6, 0x1B, 0x80, 0x5A, 0x36, 0xB4 },
+		//{ 0xC3, 0x0E, 0x01, 0x16, 0x0E, 0x32, 0x06, 0xBA, 0xE0, 0x83, 0x01, 0xFA, 0xAB, 0x3E, 0x8F, 0xAC }
+		
+		// Note: crc8=00..0F and num_ch=00..07
+		// num_ch = (rx_tx_addr[0] + rx_tx_addr[1] + rx_tx_addr[2]) % 8;
+		// crc8 = (uint16_t)LOSI_check(((rx_tx_addr[2]&0x0F) << 8) + rx_tx_addr[3]) >> 12;
 	#endif
 
-	if(IS_BIND_IN_PROGRESS)
-	{
-		bind_counter = 300;
-		CYRF_ConfigDataCode(LOSI_data_code[0], 16);				// Load bind data code
-	}
-	else
-	{
-		CYRF_ConfigDataCode(LOSI_data_code[1], 16);				// Load normal data code
-		bind_counter = 0;
-	}
+	CYRF_ConfigRFChannel(hopping_frequency[0]);
+
+	bind_counter = IS_BIND_IN_PROGRESS?300:1;
+	packet_period = 8763;
 }
 
 #endif

Multiprotocol/MLINK_cyrf6936.ino

@@ -421,7 +421,7 @@ uint16_t MLINK_callback()
 
 
 		case MLINK_PREP_DATA:
-			CYRF_ConfigDataCode(MLINK_Data_Code,16);
+			CYRF_ConfigDataCode(MLINK_Data_Code);
 			MLINK_CRC_Init += 0xED;
 			hopping_frequency_no = 0x00;
 			CYRF_ConfigRFChannel(hopping_frequency[hopping_frequency_no]);
@@ -597,7 +597,7 @@ void MLINK_init()
 	{
 		packet_count = 0;
 		bind_counter = MLINK_BIND_COUNT;
-		CYRF_ConfigDataCode((uint8_t*)"\x6F\xBE\x32\x01\xDB\xF1\x2B\x01\xE3\x5C\xFA\x02\x97\x93\xF9\x02",16); //Bind data code
+		CYRF_ConfigDataCode((uint8_t*)"\x6F\xBE\x32\x01\xDB\xF1\x2B\x01\xE3\x5C\xFA\x02\x97\x93\xF9\x02"); //Bind data code
 		CYRF_ConfigRFChannel(MLINK_BIND_CHANNEL);
 		phase = MLINK_BIND_TX;
 	}

Multiprotocol/Multi.txt

@@ -58,8 +58,7 @@
 58,FX,816,620,9630
 59,Bayang_RX,Multi,CPPM
 60,Pelikan,Pro,Lite,SCX24
-61,Tiger
-62,XK,X450,X420
+62,XK,X450,X420,Cars
 63,XN_DUMP,250K,1M,2M,AUTO
 64,FrskyX2,CH_16,CH_8,EU_16,EU_8,Cloned
 65,FrSkyR9,915MHz,868MHz,915_8ch,868_8ch,FCC,--,FCC_8ch,--_8ch
@@ -71,7 +70,7 @@
 71,JJRC345,JJRC345,SkyTmblr
 72,Q90C
 73,Kyosho,FHSS,Hype
-74,RadioLink,Surface,Air,DumboRC
+74,RadioLink,Surface,Air,DumboRC,RC4G
 75,---
 76,Realacc,R11
 77,OMP
@@ -91,3 +90,6 @@
 92,MT99xx,PA18
 93,Kyosho2,KT-17
 94,Scorpio
+95,BlueFly
+96,BumbleB
+97,SGF22

Multiprotocol/Multi_Protos.ino

@@ -81,7 +81,6 @@ const char STR_HOTT[]		="HoTT";
 const char STR_FX[]			="FX";
 const char STR_BAYANG_RX[]	="BayanRX";
 const char STR_PELIKAN[]	="Pelikan";
-const char STR_TIGER[]		="Tiger";
 const char STR_XK[]			="XK";
 const char STR_XN297DUMP[]	="XN297DP";
 const char STR_FRSKYR9[]	="FrSkyR9";
@@ -106,6 +105,9 @@ const char STR_LOSI[]       ="Losi";
 const char STR_MOULDKG[]    ="MouldKg";
 const char STR_XERALL[]     ="Xerall";
 const char STR_SCORPIO[]    ="Scorpio";
+const char STR_BLUEFLY[]    ="BlueFly";
+const char STR_BUMBLEB[]    ="BumbleB";
+const char STR_SGF22[]      ="SGF22";
 
 const char STR_SUBTYPE_FLYSKY[] =     "\x04""Std\0""V9x9""V6x6""V912""CX20";
 const char STR_SUBTYPE_HUBSAN[] =     "\x04""H107""H301""H501";
@@ -155,7 +157,7 @@ const char STR_SUBTYPE_XN297DUMP[] =  "\x07""250Kbps""1Mbps\0 ""2Mbps\0 ""Auto\0
 const char STR_SUBTYPE_ESKY150[] =    "\x03""4ch""7ch";
 const char STR_SUBTYPE_ESKY150V2[] =  "\x05""150V2";
 const char STR_SUBTYPE_V911S[] =      "\x05""V911S""E119\0";
-const char STR_SUBTYPE_XK[] =         "\x04""X450""X420";
+const char STR_SUBTYPE_XK[] =         "\x04""X450""X420""Cars";
 const char STR_SUBTYPE_FRSKYR9[] =    "\x07""915MHz\0""868MHz\0""915 8ch""868 8ch""FCC\0   ""--\0    ""FCC 8ch""-- 8ch\0";
 const char STR_SUBTYPE_ESKY[] =       "\x03""Std""ET4";
 const char STR_SUBTYPE_PROPEL[] =     "\x04""74-Z";
@@ -165,13 +167,13 @@ const char STR_SUBTYPE_WFLY2[] =      "\x05""RF20x";
 const char STR_SUBTYPE_HOTT[] =       "\x07""Sync\0  ""No_Sync";
 const char STR_SUBTYPE_PELIKAN[] =    "\x05""Pro\0 ""Lite\0""SCX24";
 const char STR_SUBTYPE_V761[] =       "\x05""3ch\0 ""4ch\0 ""TOPRC";
-const char STR_SUBTYPE_RLINK[] =      "\x07""Surface""Air\0   ""DumboRC";
+const char STR_SUBTYPE_RLINK[] =      "\x07""Surface""Air\0   ""DumboRC""RC4G\0  ";
 const char STR_SUBTYPE_REALACC[] =    "\x03""R11";
 const char STR_SUBTYPE_KYOSHO[] =     "\x04""FHSS""Hype";
 const char STR_SUBTYPE_KYOSHO2[] =    "\x05""KT-17";
 const char STR_SUBTYPE_FUTABA[] =     "\x05""SFHSS";
 const char STR_SUBTYPE_JJRC345[] =    "\x08""JJRC345\0""SkyTmblr";
-const char STR_SUBTYPE_MOULKG[] =     "\x06""Analog""Digit\0";
+const char STR_SUBTYPE_MOULDKG[] =    "\x06""Analog""Digit\0";
 const char STR_SUBTYPE_KF606[] =      "\x06""KF606\0""MIG320""ZCZ50\0";
 const char STR_SUBTYPE_E129[] =       "\x04""E129""C186";
 const char STR_SUBTYPE_FX[] =         "\x04""816\0""620\0""9630";
@@ -222,6 +224,12 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(BAYANG_RX_NRF24L01_INO)
 		{PROTO_BAYANG_RX,  STR_BAYANG_RX, STR_CPPM,       NBR_CPPM, OPTION_NONE,    0, 0, SW_NRF,    BAYANG_RX_init,  BAYANG_RX_callback  },	
 	#endif
+	#if defined(BLUEFLY_CCNRF_INO)
+		{PROTO_BLUEFLY,    STR_BLUEFLY,   NO_SUBTYPE,            0, OPTION_RFTUNE,  0, 0, SW_NRF,    BLUEFLY_init,    BLUEFLY_callback    },
+	#endif
+	#if defined(BUMBLEB_CCNRF_INO)
+		{PROTO_BUMBLEB,    STR_BUMBLEB,   NO_SUBTYPE,            0, OPTION_RFTUNE,  0, 0, SW_NRF,    BUMBLEB_init,    BUMBLEB_callback    },
+	#endif
 	#if defined(BUGS_A7105_INO)
 		{PROTO_BUGS,       STR_BUGS,      NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_A7105,  BUGS_init,       BUGS_callback       },
 	#endif
@@ -389,7 +397,7 @@ const mm_protocol_definition multi_protocols[] = {
 		{PROTO_MLINK,      STR_MLINK,     NO_SUBTYPE,            0, OPTION_NONE,    1, 0, SW_CYRF,   MLINK_init,      MLINK_callback      },
 	#endif
 	#if defined(MOULDKG_NRF24L01_INO)
-		{PROTO_MOULDKG,    STR_MOULDKG,   STR_SUBTYPE_MOULKG,    2, OPTION_OPTION,  0, 0, SW_NRF,    MOULDKG_init,    MOULDKG_callback    },
+		{PROTO_MOULDKG,    STR_MOULDKG,   STR_SUBTYPE_MOULDKG,   2, OPTION_OPTION,  0, 0, SW_NRF,    MOULDKG_init,    MOULDKG_callback    },
 	#endif
 	#if defined(MT99XX_CCNRF_INO)
 		{PROTO_MT99XX,     STR_MT99XX,    STR_SUBTYPE_MT99,      8, OPTION_NONE,    0, 0, SW_NRF,    MT99XX_init,     MT99XX_callback     },
@@ -422,7 +430,7 @@ const mm_protocol_definition multi_protocols[] = {
 		{PROTO_Q90C,       STR_Q90C,      NO_SUBTYPE,            0, OPTION_RFTUNE,  0, 0, SW_NRF,    Q90C_init,       Q90C_callback       },
 	#endif
 	#if defined(RLINK_CC2500_INO)
-		{PROTO_RLINK,      STR_RLINK,     STR_SUBTYPE_RLINK,     3, OPTION_RFTUNE,  0, 0, SW_CC2500, RLINK_init,      RLINK_callback      },
+		{PROTO_RLINK,      STR_RLINK,     STR_SUBTYPE_RLINK,     4, OPTION_RFTUNE,  0, 0, SW_CC2500, RLINK_init,      RLINK_callback      },
 	#endif
 	#if defined(REALACC_NRF24L01_INO)
 		{PROTO_REALACC,    STR_REALACC,   STR_SUBTYPE_REALACC,   1, OPTION_NONE,    0, 0, SW_NRF,    REALACC_init,    REALACC_callback    },
@@ -436,6 +444,9 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(SCORPIO_CYRF6936_INO)
 		{PROTO_SCORPIO,    STR_SCORPIO,   NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_CYRF,   SCORPIO_init,    SCORPIO_callback    },
 	#endif
+	#if defined(SGF22_NRF24L01_INO)
+		{PROTO_SGF22,      STR_SGF22,     NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    SGF22_init,      SGF22_callback      },
+	#endif
 	#if defined(SHENQI_NRF24L01_INO)
 		{PROTO_SHENQI,     STR_SHENQI,    NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    SHENQI_init,     SHENQI_callback     },
 	#endif
@@ -448,9 +459,6 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(SYMAX_NRF24L01_INO)
 		{PROTO_SYMAX,      STR_SYMAX,     STR_SUBTYPE_SYMAX,     2, OPTION_NONE,    0, 0, SW_NRF,    SYMAX_init,      SYMAX_callback      },
 	#endif
-	#if defined(TIGER_NRF24L01_INO)
-		{PROTO_TIGER,      STR_TIGER,     NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    TIGER_init,      TIGER_callback      },	
-	#endif
 	#if defined(TRAXXAS_CYRF6936_INO)
 		{PROTO_TRAXXAS,    STR_TRAXXAS,   STR_SUBTYPE_TRAXXAS,   1, OPTION_NONE,    0, 0, SW_CYRF,   TRAXXAS_init,    TRAXXAS_callback    },
 	#endif
@@ -477,7 +485,7 @@ const mm_protocol_definition multi_protocols[] = {
 		{PROTO_XERALL,     STR_XERALL,    NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    XERALL_init,     XERALL_callback     },	
 	#endif
 	#if defined(XK_CCNRF_INO)
-		{PROTO_XK,         STR_XK,        STR_SUBTYPE_XK,        2, OPTION_RFTUNE,  0, 0, SW_NRF,    XK_init,         XK_callback         },	
+		{PROTO_XK,         STR_XK,        STR_SUBTYPE_XK,        3, OPTION_RFTUNE,  0, 0, SW_NRF,    XK_init,         XK_callback         },	
 	#endif
 	#if defined(XN297DUMP_NRF24L01_INO)
 		{PROTO_XN297DUMP,  STR_XN297DUMP, STR_SUBTYPE_XN297DUMP, 6, OPTION_RFCHAN,  0, 0, SW_NRF,    XN297Dump_init,  XN297Dump_callback  },

Multiprotocol/Multiprotocol.h

@@ -19,7 +19,7 @@
 #define VERSION_MAJOR		1
 #define VERSION_MINOR		3
 #define VERSION_REVISION	3
-#define VERSION_PATCH_LEVEL	33
+#define VERSION_PATCH_LEVEL	49
 
 #define MODE_SERIAL 0
 
@@ -89,7 +89,7 @@ enum PROTOCOLS
 	PROTO_FX		= 58,	// =>NRF24L01
 	PROTO_BAYANG_RX	= 59,	// =>NRF24L01
 	PROTO_PELIKAN	= 60,	// =>A7105
-	PROTO_TIGER		= 61,	// =>NRF24L01
+
 	PROTO_XK		= 62,	// =>NRF24L01
 	PROTO_XN297DUMP	= 63,	// =>NRF24L01
 	PROTO_FRSKYX2	= 64,	// =>CC2500
@@ -122,6 +122,10 @@ enum PROTOCOLS
 	PROTO_MT99XX2	= 92,	// =>NRF24L01, extension of MT99XX protocol
 	PROTO_KYOSHO2	= 93,	// =>NRF24L01
 	PROTO_SCORPIO	= 94,	// =>CYRF6936
+	PROTO_BLUEFLY	= 95,	// =>CC2500 & NRF24L01
+	PROTO_BUMBLEB	= 96,	// =>CC2500 & NRF24L01
+	PROTO_SGF22		= 97,	// =>NRF24L01
+
 	
 	PROTO_NANORF	= 126,	// =>NRF24L01
 	PROTO_TEST		= 127,	// =>CC2500
@@ -372,6 +376,7 @@ enum XK
 {
 	X450	= 0,
 	X420	= 1,
+	XK_CARS	= 2,
 };
 enum XN297DUMP
 {
@@ -447,6 +452,7 @@ enum RLINK
 	RLINK_SURFACE	= 0,
 	RLINK_AIR		= 1,
 	RLINK_DUMBORC	= 2,
+	RLINK_RC4G		= 3,
 };
 enum MOULDKG
 {
@@ -830,7 +836,8 @@ enum {
 #define DSM_RX_EEPROM_OFFSET	877		// (4) TX ID + format, 5 bytes, end is 882
 #define MOULDKG_EEPROM_OFFSET	882		// RX ID, 3 bytes per model, end is 882+64*3=1074
 #define DSM_CLONE_EEPROM_OFFSET	1074	// (4) TX ID, (1) Initialized, end is 1079
-//#define CONFIG_EEPROM_OFFSET 	1079	// Current configuration of the multimodule
+#define TRAXXAS_EEPROM_OFFSET	1079	// RX ID and SOP index, 3 bytes per model id, end is 1079+192=1271
+//#define CONFIG_EEPROM_OFFSET 	1271	// Current configuration of the multimodule
 
 /* STM32 Flash Size */
 #ifndef DISABLE_FLASH_SIZE_CHECK
@@ -919,7 +926,6 @@ Serial: 100000 Baud 8e2      _ xxxx xxxx p --
 				FX		58
 				BAYANG_RX	59
 				PELIKAN		60
-				TIGER		61
 				XK			62
 				XN297DUMP	63
 				FRSKYX2		64

Multiprotocol/Pelikan_a7105.ino

@@ -22,7 +22,7 @@
 //#define PELIKAN_LITE_FORCE_ID
 #define PELIKAN_LITE_FORCE_HOP				// hop sequence creation is unknown
 //#define PELIKAN_SCX24_FORCE_ID
-#define PELIKAN_SCX24_FORCE_HOP				// hop sequence creation is unknown
+//#define PELIKAN_SCX24_FORCE_HOP				// hop sequence creation is unknown
 
 #define PELIKAN_BIND_COUNT		400			// 3sec
 #define PELIKAN_BIND_RF			0x3C
@@ -30,6 +30,7 @@
 #define PELIKAN_PACKET_PERIOD	7980
 #define PELIKAN_LITE_PACKET_PERIOD 18000
 #define PELIKAN_SCX24_PACKET_PERIOD 15069
+#define PELIKAN_SCX_HOP_LIMIT 90
 
 static void __attribute__((unused)) pelikan_build_packet()
 {
@@ -37,9 +38,11 @@ static void __attribute__((unused)) pelikan_build_packet()
 	uint8_t sum;
 	uint16_t channel;
 
+	#ifndef MULTI_AIR
 	if(sub_protocol == PELIKAN_SCX24)
 		packet[0] = 0x11;
 	else //PELIKAN_PRO & PELIKAN_LITE
+	#endif
 		packet[0] = 0x15;
     if(IS_BIND_IN_PROGRESS)
 	{
@@ -48,6 +51,7 @@ static void __attribute__((unused)) pelikan_build_packet()
 		packet[4] = rx_tx_addr[2];
 		packet[5] = rx_tx_addr[3];
 
+		#ifndef MULTI_AIR
 		if(sub_protocol == PELIKAN_SCX24)
 		{
 			packet[1] = 0x65;				//??
@@ -55,6 +59,7 @@ static void __attribute__((unused)) pelikan_build_packet()
 			packet[7] = 0xAA;				//??
 		}
 		else
+		#endif
 		{//PELIKAN_PRO & PELIKAN_LITE
 			packet[1] = 0x04;				//version??
 			if(sub_protocol==PELIKAN_PRO)
@@ -70,6 +75,7 @@ static void __attribute__((unused)) pelikan_build_packet()
 	{
 		//ID
 		packet[1]  = rx_tx_addr[0];
+		#ifndef MULTI_AIR
 		if(sub_protocol == PELIKAN_SCX24)
 		{
 			//ID
@@ -95,6 +101,7 @@ static void __attribute__((unused)) pelikan_build_packet()
 			packet_length = 14;
 		}
 		else
+		#endif
 		{//PELIKAN_PRO & PELIKAN_LITE
 			//ID
 			packet[7]  = rx_tx_addr[1];
@@ -158,6 +165,13 @@ static void __attribute__((unused)) pelikan_build_packet()
 
 uint16_t PELIKAN_callback()
 {
+	#ifdef MULTI_AIR
+		if(sub_protocol == PELIKAN_SCX24)
+		{
+			SUB_PROTO_INVALID;
+			return 10000;
+		}
+	#endif
 	if(phase==0)
 	{
 		#ifndef FORCE_PELIKAN_TUNING
@@ -172,10 +186,12 @@ uint16_t PELIKAN_callback()
 				A7105_Strobe(A7105_STANDBY);
 				if(sub_protocol==PELIKAN_PRO)
 					A7105_WriteReg(A7105_03_FIFOI,0x28); //????
-				else if(sub_protocol==PELIKAN_SCX24)
-					A7105_WriteReg(A7105_03_FIFOI,0x0D);
-				else//PELIKAN_LITE
+				else if(sub_protocol==PELIKAN_LITE)
 					A7105_WriteID(MProtocol_id);
+				#ifndef MULTI_AIR
+				else // PELIKAN_SCX24
+					A7105_WriteReg(A7105_03_FIFOI,0x0D);
+				#endif
 			}
 		}
 		#ifdef MULTI_SYNC
@@ -216,6 +232,82 @@ static uint8_t pelikan_firstCh(uint8_t u, uint8_t l)
 	return 0;
 }
 
+static uint8_t pelikan_firstCh_scx(uint8_t i, uint8_t j)
+{
+	uint8_t ch;
+	switch (j) {
+		case 0:
+			ch = 30;
+			break;
+		case 1:
+		case 2:
+			ch = (i * 4) + 42;
+			break;
+		case 3:
+			ch = (i * 2) + 36;
+			break;
+		case 4:
+			ch = (i * 8) + 54;
+			break;
+		case 5:
+			ch = 30;
+			break;
+	}
+
+	if (ch > PELIKAN_SCX_HOP_LIMIT)
+	{
+		do
+		{
+			ch -= 62;
+		} while (ch > PELIKAN_SCX_HOP_LIMIT);
+	}
+
+	switch (ch) {
+		case 48:
+			if (j == 3)
+				ch += 18;
+			else if (j == 4)
+				ch += 20;
+			else
+				ch += 40;
+			break;
+		case 40:
+			if (j == 4)
+				ch += 18;
+			break;
+		case 52:
+			if (j < 3)
+				ch -= 20;
+			else if (j == 4)
+				ch -= 10;
+			break;
+		case 66:
+			if  (j < 3)
+				ch += 18;
+			else if (j == 4)
+				ch -= 22;
+			break;
+		case 72:
+			if (j < 3)
+				ch -= 10;
+			else if (j ==3)
+				ch -= 20;
+			else if (j == 4)
+				ch -= 36;
+			break;
+		case 74:
+			if (j == 4)
+				ch -= 20;
+			break;
+		case 86:
+			if (j == 4)
+				ch -= 48;
+			break;
+	}
+
+	return ch;
+}
+
 static uint8_t pelikan_adjust_value(uint8_t value, uint8_t addition, uint8_t limit)
 {
 	uint8_t i;
@@ -234,6 +326,10 @@ static uint8_t pelikan_adjust_value(uint8_t value, uint8_t addition, uint8_t lim
 			value += addition;
 			i++;
 		}
+		if (value == 72) {
+			value += addition;
+			i++;
+		}
 	}
 	while (i > 0);
 
@@ -278,6 +374,121 @@ static void __attribute__((unused)) pelikan_init_hop()
 	debugln("");
 }
 
+#ifndef MULTI_AIR
+
+const uint8_t PROGMEM scx_ch_map[4][PELIKAN_NUM_RF_CHAN] = 
+	{
+		{0,1,2,26,27,28,23,24,25,20,21,22,17,18,19,14,15,16,11,12,13,8,9,10,5,6,7,4,3},
+		{0,1,2,28,25,26,27,24,21,22,23,20,17,18,19,16,13,14,15,12,9,10,11,8,5,6,7,3,4},
+		{0,1,27,28,25,26,23,24,21,22,19,20,17,18,15,16,13,14,11,12,9,10,7,8,5,6,3,4,2},
+		{0,1,28,1,4,2,23,26,22,24,27,25,17,20,16,18,21,19,11,14,10,12,15,13,27,8,6,7,9}
+	};
+
+static void pelikan_shuffle(uint8_t j)
+{
+	uint8_t temp[PELIKAN_NUM_RF_CHAN];
+	for (uint8_t i = 0; i < PELIKAN_NUM_RF_CHAN; i++)
+		temp[i] = hopping_frequency[pgm_read_byte_near(&scx_ch_map[j-1][i])];
+
+	for (uint8_t i = 0; i < PELIKAN_NUM_RF_CHAN; i++)
+		hopping_frequency[i] = temp[i];
+}
+
+static void __attribute__((unused)) pelikan_init_hop_scx()
+{
+	rx_tx_addr[0] = 0x10;
+	rx_tx_addr[1] = (rx_tx_addr[1] + RX_num) % 192;
+	debugln("TX[0]: %02X TX[1]: %02X", rx_tx_addr[0], rx_tx_addr[1]);
+	
+	uint8_t high = (rx_tx_addr[1]>>4);
+	uint8_t low = rx_tx_addr[1] & 0x0F;
+	int16_t i = (high * 10) + low - 23;
+	uint8_t j = 0;
+
+	if (i > 0)
+		j = 1;
+	
+	if (i > 24)
+	{
+		do
+		{
+			i -= 24;
+			j++;
+		} while (i > 24);
+	}
+
+	debugln("H: %02X L: %02X I: %02X J: %02X", high, low, i, j);
+
+	uint8_t first_channel;
+	uint8_t last_channel;
+	uint8_t addition;
+
+	first_channel = pelikan_firstCh_scx(i, j);
+
+	if (j == 0)
+		last_channel = 42 - (high * 10) - low;
+	else
+		last_channel = 42 - i + 1;
+
+	if (last_channel == 24)
+		last_channel += 9;
+	
+	if (last_channel == 36)
+		last_channel -= 10;
+
+	if (j == 0)
+		addition = (2 * i) + 54;
+	else if (j == 5)
+		addition = (2 * i) + 6;
+	else
+		addition = 56 - (2 * i);
+
+	hopping_frequency[0] = first_channel;
+	for (uint8_t i = 1; i < PELIKAN_NUM_RF_CHAN; i++)
+	{
+		hopping_frequency[i] = pelikan_add(hopping_frequency[i-1], addition, PELIKAN_SCX_HOP_LIMIT);
+	}
+
+	if (j > 0 && j < 5)
+		pelikan_shuffle(j);
+
+	if (j == 2)
+	{
+		hopping_frequency[PELIKAN_NUM_RF_CHAN - 2] = last_channel;
+	} else if (j == 4)
+	{
+		uint8_t t = (2 * i) + 36;
+		if (t == 48)
+			t += 18;
+		if (t == 72)
+			t -= 20;
+
+		hopping_frequency[1] = t;
+		hopping_frequency[PELIKAN_NUM_RF_CHAN - 5] = last_channel;
+	}	
+	else
+	{
+		hopping_frequency[PELIKAN_NUM_RF_CHAN - 1] = last_channel;
+	}
+
+	#ifdef DEBUG_SERIAL
+		for (uint8_t i = 0; i < PELIKAN_NUM_RF_CHAN; i++)
+			debug("%02X ", hopping_frequency[i]);
+		debugln("");
+	#endif
+}
+
+#ifdef PELIKAN_SCX24_FORCE_HOP
+const uint8_t PROGMEM pelikan_scx24_hopp[][PELIKAN_NUM_RF_CHAN] = {
+/*TX1*/	{ 0x1E,0x32,0x46,0x5A,0x44,0x58,0x2E,0x42,0x56,0x2C,0x40,0x54,0x2A,0x3E,0x52,0x28,0x3C,0x50,0x26,0x3A,0x4E,0x24,0x38,0x4C,0x22,0x36,0x4A,0x20,0x1A },
+/*TX2*/	{ 0x2C,0x44,0x1E,0x52,0x56,0x22,0x3A,0x3E,0x34,0x4C,0x26,0x5A,0x50,0x2A,0x42,0x38,0x2E,0x46,0x20,0x54,0x4A,0x24,0x3C,0x32,0x28,0x40,0x58,0x1B,0x4E },
+/*TX3*/	{ 0x3C,0x4C,0x1E,0x4A,0x5A,0x2C,0x58,0x2A,0x3A,0x56,0x28,0x38,0x26,0x36,0x46,0x34,0x44,0x54,0x42,0x52,0x24,0x50,0x22,0x32,0x4E,0x20,0x40,0x3E,0x17 },
+/*TX4*/	{ 0x46,0x32,0x1E,0x58,0x44,0x5A,0x56,0x42,0x2E,0x54,0x40,0x2C,0x52,0x3E,0x2A,0x50,0x3C,0x28,0x4E,0x3A,0x26,0x4C,0x38,0x24,0x4A,0x36,0x22,0x20,0x1A }
+};
+#endif //PELIKAN_SCX24_FORCE_HOP
+
+#endif //MULTI_AIR
+
 #ifdef PELIKAN_FORCE_ID
 const uint8_t PROGMEM pelikan_hopp[][PELIKAN_NUM_RF_CHAN] = {
 	{ 0x5A,0x46,0x32,0x6E,0x6C,0x58,0x44,0x42,0x40,0x6A,0x56,0x54,0x52,0x3E,0x68,0x66,0x64,0x50,0x3C,0x3A,0x38,0x62,0x4E,0x4C,0x5E,0x4A,0x36,0x5C,0x34 }
@@ -289,12 +500,6 @@ const uint8_t PROGMEM pelikan_lite_hopp[][PELIKAN_NUM_RF_CHAN] = {
 	{ 0x46,0x2A,0x3E,0x5A,0x5C,0x24,0x4E,0x32,0x54,0x26,0x2C,0x34,0x56,0x1E,0x3A,0x3C,0x50,0x4A,0x2E,0x42,0x20,0x52,0x28,0x22,0x44,0x58,0x36,0x38,0x4C }
 };
 #endif
-#ifdef PELIKAN_SCX24_FORCE_HOP
-const uint8_t PROGMEM pelikan_scx24_hopp[][PELIKAN_NUM_RF_CHAN] = {
-	{ 0x1E,0x32,0x46,0x5A,0x44,0x58,0x2E,0x42,0x56,0x2C,0x40,0x54,0x2A,0x3E,0x52,0x28,0x3C,0x50,0x26,0x3A,0x4E,0x24,0x38,0x4C,0x22,0x36,0x4A,0x20,0x1A },
-	{ 0x2C,0x44,0x1E,0x52,0x56,0x22,0x3A,0x3E,0x34,0x4C,0x26,0x5A,0x50,0x2A,0x42,0x38,0x2E,0x46,0x20,0x54,0x4A,0x24,0x3C,0x32,0x28,0x40,0x58,0x1B,0x4E }
-};
-#endif
 
 void PELIKAN_init()
 {
@@ -341,22 +546,32 @@ void PELIKAN_init()
 				A7105_WriteID(MProtocol_id);
 			packet_period = PELIKAN_LITE_PACKET_PERIOD;
 		}
+		#ifndef MULTI_AIR
 		else// if(sub_protocol==PELIKAN_SCX24)
 		{
+			pelikan_init_hop_scx();
 			#if defined(PELIKAN_SCX24_FORCE_HOP)
 				// Hop frequency table
-				uint8_t num=rx_tx_addr[3] & 0x01;
-				if(num)
-				{//1
+				uint8_t num=rx_tx_addr[3] & 0x03;
+				switch(num)
+				{
+					case 1:
 						rx_tx_addr[0]=0x10;		// hopping freq TX2
 						rx_tx_addr[1]=0x63;		// hopping freq TX2
-				}
-				else
-				{//0
+						break;
+					case 2:
+						rx_tx_addr[0]=0x81;		// hopping freq TX3
+						rx_tx_addr[1]=0x63;		// hopping freq TX3
+						break;
+					case 3:
+						rx_tx_addr[0]=0x36;		// hopping freq TX4
+						rx_tx_addr[1]=0x5C;		// hopping freq TX4
+						break;
+					default:
 						rx_tx_addr[0]=0x12;		// hopping freq TX1
 						rx_tx_addr[1]=0x46;		// hopping freq TX1
+						break;
 				}
-
 				for(uint8_t i=0;i<PELIKAN_NUM_RF_CHAN;i++)
 					hopping_frequency[i]=pgm_read_byte_near(&pelikan_scx24_hopp[num][i]);
 			#endif
@@ -366,12 +581,17 @@ void PELIKAN_init()
 				rx_tx_addr[3]=0x19;			// TX1
 				rx_tx_addr[2]=0x80;			// TX2
 				rx_tx_addr[3]=0x22;			// TX2
+				rx_tx_addr[2]=0x30;			// TX3
+				rx_tx_addr[3]=0x18;			// TX3
+				rx_tx_addr[2]=0x30;			// TX4
+				rx_tx_addr[3]=0x17;			// TX4
 			#endif
 			A7105_WriteReg(A7105_0E_DATA_RATE,0x03);
 			if(IS_BIND_DONE)
 				A7105_WriteReg(A7105_03_FIFOI,0x0D);
 			packet_period = PELIKAN_SCX24_PACKET_PERIOD;
 		}
+		#endif //MULTI_AIR
 	}
 
 	hopping_frequency_no = PELIKAN_NUM_RF_CHAN;

Multiprotocol/RadioLink_cc2500.ino

@@ -18,7 +18,11 @@
 
 #include "iface_cc2500.h"
 
+//#define RLINK_DEBUG
+//#define RLINK_DEBUG_TELEM
+
 //#define RLINK_FORCE_ID
+#define RLINK_RC4G_FORCE_ID
 
 #define RLINK_TX_PACKET_LEN	33
 #define RLINK_RX_PACKET_LEN	15
@@ -97,16 +101,37 @@ static void __attribute__((unused)) RLINK_hop()
 
 static void __attribute__((unused)) RLINK_TXID_init()
 {
+	#ifdef RLINK_RC4G_FORCE_ID
+		//TODO: test any ID
+		if(sub_protocol==RLINK_RC4G)
+		{
+			rx_tx_addr[1]=0x77;
+			rx_tx_addr[2]=0x00;
+			rx_tx_addr[3]=0x00;
+		}
+	#endif
 	#ifdef RLINK_FORCE_ID
-		//surface RC6GS
-		memcpy(rx_tx_addr,"\x3A\x99\x22\x3A",RLINK_TX_ID_LEN);
-		//air T8FB
-		//memcpy(rx_tx_addr,"\xFC\x11\x0D\x20",RLINK_TX_ID_LEN);
+		if(sub_protocol==RLINK_SURFACE)
+			memcpy(rx_tx_addr,"\x3A\x99\x22\x3A",RLINK_TX_ID_LEN);	//surface RC6GS
+		else
+			memcpy(rx_tx_addr,"\xFC\x11\x0D\x20",RLINK_TX_ID_LEN);	//air T8FB
 	#endif
 	// channels order depend on ID
+	if(sub_protocol!=RLINK_RC4G)
 		RLINK_hop();
+	else
+	{
+		// Find 2 unused channels
+		//  first  channel is a multiple of 3 between 00 and 5D
+		//  second channel is a multiple of 3 between 63 and BD
+		//TODO: find 2 unused channels
+		#ifdef RLINK_RC4G_FORCE_ID
+			hopping_frequency[0] = 0x03;
+			hopping_frequency[1] = 0x6F;
+		#endif
+	}
 
- 	#if 0
+ 	#ifdef RLINK_DEBUG
 		debug("ID:");
 		for(uint8_t i=0;i<RLINK_TX_ID_LEN;i++)
 			debug(" 0x%02X",rx_tx_addr[i]);
@@ -138,6 +163,8 @@ static void __attribute__((unused)) RLINK_rf_init()
 		CC2500_WriteReg(4, 0xBA);
 		CC2500_WriteReg(5, 0xDC);
 	}
+	else if(sub_protocol==RLINK_RC4G)
+		CC2500_WriteReg(5, 0xA5);
 		
 	CC2500_WriteReg(CC2500_0C_FSCTRL0, option);
 	
@@ -219,18 +246,71 @@ static void __attribute__((unused)) RLINK_send_packet()
 	packet_count++;
 	if(packet_count>5) packet_count=0;
 
-	//debugln("C= 0x%02X",hopping_frequency[pseudo & 0x0F]);
-	//debug("P=");
-	//for(uint8_t i=1;i<RLINK_TX_PACKET_LEN+1;i++)
-	//	debug(" 0x%02X",packet[i]);
-	//debugln("");
+	#ifdef RLINK_DEBUG
+		debugln("C= 0x%02X",hopping_frequency[pseudo & 0x0F]);
+		debug("P=");
+		for(uint8_t i=1;i<RLINK_TX_PACKET_LEN+1;i++)
+			debug(" 0x%02X",packet[i]);
+		debugln("");
+	#endif
+}
+
+static void __attribute__((unused)) RLINK_RC4G_send_packet()
+{
+	uint32_t val;
+	//hop
+	CC2500_WriteReg(CC2500_0A_CHANNR, hopping_frequency[packet_count>>1]);
+	#ifdef RLINK_DEBUG
+		debug("C= 0x%02X ",hopping_frequency[packet_count>>1]);
+	#endif
+	// packet length
+	packet[0] = 0x0F;
+	//address
+	memcpy(&packet[1], &rx_tx_addr[1], 3);
+	//channels
+	for(uint8_t i=0;i<2;i++)
+	{
+		val = Channel_data[2*i  ] +400 -24;
+		packet[4+i*2] = val;
+		packet[8+i  ] = val>>8;
+		val = Channel_data[2*i+1] +400 -24;
+		packet[5+i*2] = val;
+		packet[8+i  ] |= (val>>4) & 0xF0;
+	}
+	//special channel which is linked to gyro on the orginal TX but allocating it on CH5 here
+	packet[10] = convert_channel_16b_limit(CH5,0,100);
+	//failsafe
+	for(uint8_t i=0;i<4;i++)
+		packet[11+i] = convert_channel_16b_limit(CH6+i,0,200);
+	//next hop
+	packet_count++;
+	packet_count &= 0x03;
+	packet[15] = hopping_frequency[packet_count>>1];
+	// send packet
+	CC2500_WriteData(packet, 16);
+
+	#ifdef RLINK_DEBUG
+		debug("P=");
+		for(uint8_t i=1;i<16;i++)
+		debug(" 0x%02X",packet[i]);
+		debugln("");
+	#endif
 }
 
 #define RLINK_TIMING_PROTO	20000-100		// -100 for compatibility with R8EF
 #define RLINK_TIMING_RFSEND	10500
 #define RLINK_TIMING_CHECK	2000
+#define RLINK_RC4G_TIMING_PROTO 14460
 uint16_t RLINK_callback()
 {
+	if(sub_protocol == RLINK_RC4G)
+	{
+		#ifdef MULTI_SYNC
+			telemetry_set_input_sync(RLINK_RC4G_TIMING_PROTO);
+		#endif
+		RLINK_RC4G_send_packet();
+		return RLINK_RC4G_TIMING_PROTO;
+	}
 	switch(phase)
 	{
 		case RLINK_DATA:
@@ -259,13 +339,16 @@ uint16_t RLINK_callback()
 			len = CC2500_ReadReg(CC2500_3B_RXBYTES | CC2500_READ_BURST) & 0x7F;	
 			if (len == RLINK_RX_PACKET_LEN + 1 + 2)			//Telemetry frame is 15 bytes + 1 byte for length + 2 bytes for RSSI&LQI&CRC
 			{
-				//debug("Telem:");
+				#ifdef RLINK_DEBUG_TELEM
+					debug("Telem:");
+				#endif
 				CC2500_ReadData(packet_in, len);
 				if(packet_in[0]==RLINK_RX_PACKET_LEN && (packet_in[len-1] & 0x80) && memcmp(&packet[2],rx_tx_addr,RLINK_TX_ID_LEN)==0 && packet_in[6]==packet[1])
 				{//Correct telemetry received: length, CRC, ID and type
-					//Debug
-					//for(uint8_t i=0;i<len;i++)
-					//	debug(" %02X",packet_in[i]);
+					#ifdef RLINK_DEBUG_TELEM
+						for(uint8_t i=0;i<len;i++)
+							debug(" %02X",packet_in[i]);
+					#endif
 					TX_RSSI = packet_in[len-2];
 					if(TX_RSSI >=128)
 						TX_RSSI -= 128;
@@ -278,7 +361,9 @@ uint16_t RLINK_callback()
 					pps_counter++;
 					packet_count=0;
 				}
-				//debugln("");
+				#ifdef RLINK_DEBUG_TELEM
+					debugln("");
+				#endif
 			}
 			if (millis() - pps_timer >= 2000)
 			{//1 telemetry packet every 100ms

Multiprotocol/SGF22_nrf24l01.ino

@@ -0,0 +1,170 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+// Compatible with SGF22 R11
+
+#if defined(SGF22_NRF24L01_INO)
+
+#include "iface_xn297.h"
+
+//#define FORCE_SGF22_ORIGINAL_ID
+
+#define SGF22_PACKET_PERIOD		11950 //10240
+#define SGF22_BIND_RF_CHANNEL	78
+#define SGF22_PAYLOAD_SIZE		12
+#define SGF22_BIND_COUNT		50
+#define SGF22_RF_NUM_CHANNELS	4
+
+//packet[8]
+#define SGF22_FLAG_3D			0x00
+#define SGF22_FLAG_ROLL			0x08
+#define SGF22_FLAG_LIGHT		0x04
+#define SGF22_FLAG_VIDEO		0x10
+#define SGF22_FLAG_6G			0x40
+#define SGF22_FLAG_VERTICAL		0xC0
+//packet[9]
+#define SGF22_FLAG_PHOTO		0x40
+
+static void __attribute__((unused)) SGF22_send_packet()
+{
+	if(IS_BIND_IN_PROGRESS)
+	{
+		packet[ 0] = 0x5B;
+		packet[ 8] = 0x00;								// ??? do they have to be 0 for bind to succeed ?
+		packet[ 9] = 0x00;								// ??? do they have to be 0 for bind to succeed ?
+		packet[10] = 0xAA;
+		packet[11] = 0x55;
+	}
+	else
+	{
+		//hop
+		XN297_Hopping(packet_sent & 0x03);				// ??? from the dumps I can't really say how hop and seq are sync, there could be an offset (0,1,2,3)...
+		//sequence from 02 to 7A by increments of 4, sometimes with a flag 0x80 from 82 to FA, I can't tell from the dumps when the switch happens
+		if( (packet_sent & 0x03) == 0x02)
+			packet_count = packet_sent;
+		packet_sent++;
+		if(packet_sent > 0x7B)
+			packet_sent = 0;
+		//packet
+		packet[0] = 0x1B;
+		packet[8] = SGF22_FLAG_3D						// default
+				| GET_FLAG(CH6_SW, SGF22_FLAG_ROLL)		// roll
+				| GET_FLAG(CH7_SW, SGF22_FLAG_LIGHT)	// push up throttle trim for light
+				| GET_FLAG(CH9_SW, SGF22_FLAG_VIDEO);   // push down throttle trim for video
+		if(Channel_data[CH5] > CHANNEL_MIN_COMMAND)
+			packet[8] |= SGF22_FLAG_6G;					// mode 1 - 6g
+		if(Channel_data[CH5] > CHANNEL_MAX_COMMAND)
+			packet[8] |= SGF22_FLAG_VERTICAL;			// mode 0 - vertical
+		packet[9] = GET_FLAG(CH8_SW, SGF22_FLAG_PHOTO);	// press in throttle trim for photo
+		packet[10] = 0x42;								// no fine tune
+		packet[11] = 0x10;								// no fine tune
+	}
+	packet[1] = packet_count;							// sequence
+	packet[2] = rx_tx_addr[2];
+	packet[3] = rx_tx_addr[3];
+	packet[4] = convert_channel_8b(THROTTLE);
+	packet[5] = convert_channel_8b(RUDDER);
+	packet[6] = convert_channel_8b(ELEVATOR);
+	packet[7] = convert_channel_8b(AILERON);
+
+	XN297_SetPower();
+	XN297_SetTxRxMode(TX_EN);
+	XN297_WriteEnhancedPayload(packet, SGF22_PAYLOAD_SIZE,0);
+	#if 0
+		debug_time("");
+		for(uint8_t i=0; i<SGF22_PAYLOAD_SIZE; i++)
+			debug(" %02X",packet[i]);
+		debugln("");
+	#endif
+}
+
+static void __attribute__((unused)) SGF22_initialize_txid()
+{
+	uint8_t val = (( (uint16_t) rx_tx_addr[2] << 8 ) | rx_tx_addr[3])%5;
+
+	const uint8_t hop[5][4] =
+	{ { 0x0C, 0x2A, 0x1B, 0x39 },
+	  { 0x0F, 0x2D, 0x1E, 0x3D },
+	  { 0x12, 0x31, 0x21, 0x41 },
+	  { 0x15, 0x34, 0x24, 0x44 },
+	  { 0x18, 0x37, 0x27, 0x47 } };
+	memcpy(hopping_frequency, &hop[val], SGF22_RF_NUM_CHANNELS);
+	
+	/*//Same code sze...
+	hopping_frequency[0] = 0x0C + 3 * val;
+	hopping_frequency[1] = hopping_frequency[0] + 0x1E;
+	if(val > 1) hopping_frequency[1]++;
+	hopping_frequency[2] = hopping_frequency[0] + 0x0F;
+	hopping_frequency[3] = hopping_frequency[1] + 0x0F;
+	if(val    ) hopping_frequency[3]++;*/
+	
+	#ifdef FORCE_SGF22_ORIGINAL_ID
+		rx_tx_addr[2] = 0x1F;
+		rx_tx_addr[3] = 0x61;
+		memcpy(hopping_frequency,"\x15\x34\x24\x44", SGF22_RF_NUM_CHANNELS);    //Original dump=>21=0x15,52=0x34,36=0x24,68=0x44
+	#endif
+	#if 0
+		debug("ID: %02X %02X, C: ",rx_tx_addr[2],rx_tx_addr[3]);
+		for(uint8_t i=0; i<SGF22_RF_NUM_CHANNELS; i++)
+			debug(" %02X",hopping_frequency[i]);
+		debugln("");
+	#endif
+}
+
+static void __attribute__((unused)) SGF22_RF_init()
+{
+	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_1M);
+	XN297_SetTXAddr((uint8_t*)"\xC7\x95\x3C\xBB\xA5", 5);
+	XN297_RFChannel(SGF22_BIND_RF_CHANNEL);			// Set bind channel
+}
+
+uint16_t SGF22_callback()
+{
+	if(phase == 0)
+	{
+		phase++;
+		#ifdef MULTI_SYNC
+			telemetry_set_input_sync(SGF22_PACKET_PERIOD);
+		#endif
+		SGF22_send_packet();
+		if(IS_BIND_IN_PROGRESS)
+		{
+			if(--bind_counter==0)
+				BIND_DONE;
+		}
+	}
+	else
+	{//send 3 times in total the same packet
+		NRF24L01_Strobe(REUSE_TX_PL);
+		phase++;
+		if(phase > 2)
+		{
+			phase = 0;
+			return SGF22_PACKET_PERIOD - 2*1550;
+		}
+	}
+	return 1550;
+}
+
+void SGF22_init()
+{
+	BIND_IN_PROGRESS;	// autobind protocol
+	SGF22_initialize_txid();
+	SGF22_RF_init();
+	bind_counter=SGF22_BIND_COUNT;
+	packet_sent = packet_count = 0x26;
+	phase = 0;
+}
+
+#endif

Multiprotocol/TRAXXAS_cyrf6936.ino

@@ -20,23 +20,22 @@
 #include "iface_cyrf6936.h"
 
 //#define TRAXXAS_FORCE_ID
+//#define TRAXXAS_DEBUG
 
-#define TRAXXAS_CHANNEL 0x05
 #define TRAXXAS_BIND_CHANNEL	0x2B
+#define TRAXXAS_CHECK_CHANNEL	0x22
 #define TRAXXAS_PACKET_SIZE		16
 
 enum {
 	TRAXXAS_BIND_PREP_RX=0,
 	TRAXXAS_BIND_RX,
 	TRAXXAS_BIND_TX1,
+	TRAXXAS_PREP_RX,
+	TRAXXAS_RX,
 	TRAXXAS_PREP_DATA,
 	TRAXXAS_DATA,
 };
 
-const uint8_t PROGMEM TRAXXAS_sop_bind[] ={ 0x3C, 0x37, 0xCC, 0x91, 0xE2, 0xF8, 0xCC, 0x91 };
-const uint8_t PROGMEM TRAXXAS_sop_data[] ={ 0xA1, 0x78, 0xDC, 0x3C, 0x9E, 0x82, 0xDC, 0x3C };
-//const uint8_t PROGMEM TRAXXAS_sop_check[]={ 0x97, 0xE5, 0x14, 0x72, 0x7F, 0x1A, 0x14, 0x72 };
-
 const uint8_t PROGMEM TRAXXAS_init_vals[][2] = {
 	//Init from dump
 	{CYRF_0B_PWR_CTRL, 0x00},					// PMU
@@ -52,23 +51,33 @@ const uint8_t PROGMEM TRAXXAS_init_vals[][2] = {
 
 static void __attribute__((unused)) TRAXXAS_cyrf_bind_config()
 {
-	CYRF_PROGMEM_ConfigSOPCode(TRAXXAS_sop_bind);
+	CYRF_PROGMEM_ConfigSOPCode(DEVO_j6pro_sopcodes[0]);
 	CYRF_WriteRegister(CYRF_15_CRC_SEED_LSB, 0x5A);
 	CYRF_WriteRegister(CYRF_16_CRC_SEED_MSB, 0x5A);
 	CYRF_ConfigRFChannel(TRAXXAS_BIND_CHANNEL);
 }
 
+static void __attribute__((unused)) TRAXXAS_cyrf_check_config()
+{
+	CYRF_ConfigRFChannel(TRAXXAS_CHECK_CHANNEL);
+	CYRF_PROGMEM_ConfigSOPCode(DEVO_j6pro_sopcodes[9]);
+	CYRF_WriteRegister(CYRF_15_CRC_SEED_LSB, 0xA5);
+	CYRF_WriteRegister(CYRF_16_CRC_SEED_MSB, 0xA5);
+}
+
 static void __attribute__((unused)) TRAXXAS_cyrf_data_config()
 {
-	CYRF_PROGMEM_ConfigSOPCode(TRAXXAS_sop_data);
+	CYRF_ConfigRFChannel(hopping_frequency[0]);
 	#ifdef TRAXXAS_FORCE_ID					// data taken from TX dump
 		CYRF_WriteRegister(CYRF_15_CRC_SEED_LSB, 0x1B);
 		CYRF_WriteRegister(CYRF_16_CRC_SEED_MSB, 0x3F);
+		CYRF_PROGMEM_ConfigSOPCode(DEVO_j6pro_sopcodes[6]);
 	#else
-		CYRF_WriteRegister(CYRF_15_CRC_SEED_LSB, cyrfmfg_id[0]+0xB6);
-		CYRF_WriteRegister(CYRF_16_CRC_SEED_MSB, cyrfmfg_id[1]+0x5D);
+		uint16_t addr=TRAXXAS_EEPROM_OFFSET+RX_num*3;
+		CYRF_WriteRegister(CYRF_15_CRC_SEED_LSB, cyrfmfg_id[0] - eeprom_read_byte((EE_ADDR)(addr + 0)));
+		CYRF_WriteRegister(CYRF_16_CRC_SEED_MSB, cyrfmfg_id[1] - eeprom_read_byte((EE_ADDR)(addr + 1)));
+		CYRF_PROGMEM_ConfigSOPCode(DEVO_j6pro_sopcodes[eeprom_read_byte((EE_ADDR)(addr + 2)) % 20]);
 	#endif
-	CYRF_ConfigRFChannel(TRAXXAS_CHANNEL);
 	CYRF_SetTxRxMode(TX_EN);
 }
 
@@ -76,6 +85,8 @@ static void __attribute__((unused)) TRAXXAS_send_data_packet()
 {
 	packet[0] = 0x01;
 	memset(&packet[1],0x00,TRAXXAS_PACKET_SIZE-1);
+	//Next RF channel ? 0x00 -> keep current, 0x0E change to F=15
+	//packet[1] = hopping_frequency[0] - 1;
 	//Steering
 	uint16_t ch = convert_channel_16b_nolimit(RUDDER,500,1000,false);
 	packet[2]=ch>>8;
@@ -104,39 +115,76 @@ uint16_t TRAXXAS_callback()
 	switch(phase)
 	{
 		case TRAXXAS_BIND_PREP_RX:
+		case TRAXXAS_PREP_RX:
+			//debugln("PREP_RX");
+			if(phase == TRAXXAS_BIND_PREP_RX)
 				TRAXXAS_cyrf_bind_config();
+			else
+				TRAXXAS_cyrf_check_config();
 			CYRF_SetTxRxMode(RX_EN);								//Receive mode
 			CYRF_WriteRegister(CYRF_05_RX_CTRL, 0x83);				//Prepare to receive
 			packet_count=100;										//Timeout for RX
-			phase=TRAXXAS_BIND_RX;
-			return 700;
+			phase++;	// TRAXXAS_BIND_RX or TRAXXAS_RX
+			return 7000;
 		case TRAXXAS_BIND_RX:
+		case TRAXXAS_RX:
+			//debugln("RX");
 			//Read data from RX
 			status = CYRF_ReadRegister(CYRF_07_RX_IRQ_STATUS);
 			if((status & 0x03) == 0x02)  							// RXC=1, RXE=0 then 2nd check is required (debouncing)
 				status |= CYRF_ReadRegister(CYRF_07_RX_IRQ_STATUS);
-			debugln("s=%02X",status);
+			#ifdef TRAXXAS_DEBUG
+				//debugln("s=%02X",status);
+			#endif
 			CYRF_WriteRegister(CYRF_07_RX_IRQ_STATUS, 0x80);		// need to set RXOW before data read
 			if((status & 0x07) == 0x02)
 			{ // Data received with no errors
 				len=CYRF_ReadRegister(CYRF_09_RX_COUNT);
+				#ifdef TRAXXAS_DEBUG
 					debugln("L=%02X",len)
+				#endif
 				if(len==TRAXXAS_PACKET_SIZE)
 				{
 					CYRF_ReadDataPacketLen(packet, TRAXXAS_PACKET_SIZE);
+					#ifdef TRAXXAS_DEBUG
 						debug("RX=");
 						for(uint8_t i=0;i<TRAXXAS_PACKET_SIZE;i++)
 							debug(" %02X",packet[i]);
 						debugln("");
+					#endif
+					uint16_t addr=TRAXXAS_EEPROM_OFFSET+RX_num*3;
+					if(phase == TRAXXAS_BIND_RX)
+					{
+						// Store RX ID
+						for(uint8_t i=0;i<2;i++)
+							eeprom_write_byte((EE_ADDR)(addr+i),packet[i+1]);
+						//Store SOP index
+						eeprom_write_byte((EE_ADDR)(addr+2),packet[7]);
+					}
+					else
+					{
+						//check RX ID and SOP
+						if(eeprom_read_byte((EE_ADDR)(addr + 0)) != packet[1] || eeprom_read_byte((EE_ADDR)(addr + 1)) != packet[2] || eeprom_read_byte((EE_ADDR)(addr + 2)) != packet[7])
+						{ // Not our RX
+							phase++;	// TRAXXAS_PREP_DATA
+							return 10000-7000-500;
+						}
+					}
+					// Replace RX ID by TX ID
 					for(uint8_t i=0;i<6;i++)
 						packet[i+1]=cyrfmfg_id[i];
-					packet[10]=0x01;
+					//packet[7 ] = 0xEE;							// Not needed ??
+					packet[8 ] = hopping_frequency[0] - 1;
+					packet[10] = 0x01;								// Must change otherwise bind doesn't complete
+					//packet[13] = 0x05;							// Not needed ??
 					packet_count=12;
 					CYRF_SetTxRxMode(TX_EN);
 					phase=TRAXXAS_BIND_TX1;
-					return 200;
+					return 10000;
 				}
 			}
+			if(phase == TRAXXAS_BIND_RX)
+			{
 				if( --packet_count == 0 )
 				{ // Retry RX
 					CYRF_WriteRegister(CYRF_29_RX_ABORT, 0x20);		// Enable RX abort
@@ -148,27 +196,40 @@ uint16_t TRAXXAS_callback()
 						phase=TRAXXAS_PREP_DATA;					// Abort binding
 				}
 				return 700;
+			}
+			CYRF_WriteRegister(CYRF_29_RX_ABORT, 0x20);				// Enable RX abort
+			CYRF_WriteRegister(CYRF_0F_XACT_CFG, 0x24);				// Force end state
+			CYRF_WriteRegister(CYRF_29_RX_ABORT, 0x00);				// Disable RX abort
+			phase++;	// TRAXXAS_PREP_DATA
+			return 10000-7000-500;
 		case TRAXXAS_BIND_TX1:
+			//debugln("BIND_TX1");
 			CYRF_WriteDataPacketLen(packet, TRAXXAS_PACKET_SIZE);
+			#ifdef TRAXXAS_DEBUG
 				debug("P=");
 				for(uint8_t i=0;i<TRAXXAS_PACKET_SIZE;i++)
 					debug(" %02X",packet[i]);
 				debugln("");
+			#endif
 			if(--packet_count==0)	// Switch to normal mode
 				phase=TRAXXAS_PREP_DATA;
 			break;
 		case TRAXXAS_PREP_DATA:
+			//debugln("PREP_DATA");
 			BIND_DONE;
 			TRAXXAS_cyrf_data_config();
 			phase++;
+			return 500;
 		case TRAXXAS_DATA:
+			//debugln_time("DATA");
 			#ifdef MULTI_SYNC
-				telemetry_set_input_sync(13940);
+				telemetry_set_input_sync(10000);
 			#endif
 			TRAXXAS_send_data_packet();
-			break;
+			phase = TRAXXAS_PREP_RX;
+			return 1000;
 	}
-	return 13940;
+	return 10000;
 }
 
 void TRAXXAS_init()
@@ -179,8 +240,8 @@ void TRAXXAS_init()
 
 	//Read CYRF ID
 	CYRF_GetMfgData(cyrfmfg_id);
-	cyrfmfg_id[0]+=RX_num;
-
+	//cyrfmfg_id[0]+=RX_num;				// Not needed since the TX and RX have to match
+	CYRF_FindBestChannels(hopping_frequency,1,1,0x02,0x21);
 	#ifdef TRAXXAS_FORCE_ID					// data taken from TX dump
 		cyrfmfg_id[0]=0x65;					// CYRF MFG ID
 		cyrfmfg_id[1]=0xE2;
@@ -188,6 +249,11 @@ void TRAXXAS_init()
 		cyrfmfg_id[3]=0x55;
 		cyrfmfg_id[4]=0x4D;
 		cyrfmfg_id[5]=0xFE;
+		hopping_frequency[0] = 0x05;					// seen 05 and 0F
+	#endif
+	#ifdef TRAXXAS_DEBUG
+		debugln("ID: %02X %02X %02X %02X %02X %02X",cyrfmfg_id[0],cyrfmfg_id[1],cyrfmfg_id[2],cyrfmfg_id[3],cyrfmfg_id[4],cyrfmfg_id[5]);
+		debugln("RF CH: %02X",hopping_frequency[0]);
 	#endif
 	
 	if(IS_BIND_IN_PROGRESS)
@@ -197,39 +263,88 @@ void TRAXXAS_init()
 	}
 	else
 		phase = TRAXXAS_PREP_DATA;
+	
+	//
+//	phase = TRAXXAS_BIND_TX1;
+//	TRAXXAS_cyrf_bind_config();
+//	CYRF_SetTxRxMode(TX_EN);
+//	memcpy(packet,(uint8_t *)"\x02\x4A\xA3\x2D\x1A\x49\xFE\x06\x00\x00\x02\x01\x06\x06\x00\x00",TRAXXAS_PACKET_SIZE);
+//	memcpy(packet,(uint8_t *)"\x02\x49\xAC\x4F\x55\x4D\xFE\x05\x00\x00\x02\x01\x06\x06\x00\x00",TRAXXAS_PACKET_SIZE);
 }
 
 /*
-Bind phase 1
+Packets 0x02: Bind learn TX/RX addresses
 CHANNEL:	0x2B
 SOP_CODE:	0x3C	0x37	0xCC	0x91	0xE2	0xF8	0xCC	0x91
 CRC_SEED_LSB:	0x5A
 CRC_SEED_MSB:	0x5A
-RX1:	0x02	0x4A	0xA3	0x2D	0x1A	0x49	0xFE	0x06	0x00	0x00	0x02	0x01	0x06	0x06	0x00	0x00
-TX1:	0x02	0x65	0xE2	0x5E	0x55	0x4D	0xFE	0xEE	0x00	0x00	0x01	0x01	0x06	0x05	0x00	0x00
-Note: RX cyrfmfg_id is 0x4A,0xA3,0x2D,0x1A,0x49,0xFE and TX cyrfmfg_id is 0x65,0xE2,0x5E,0x55,0x4D,0xFE
+RX:	0x02	0x4A	0xA3	0x2D	0x1A	0x49	0xFE	0x06	0x00	0x00	0x02	0x01	0x06	0x06	0x00	0x00
+TX:	0x02	0x65	0xE2	0x5E	0x55	0x4D	0xFE	0xEE	0x00	0x00	0x01	0x01	0x06	0x05	0x00	0x00
+Notes:
+ - RX cyrfmfg_id is 0x4A,0xA3,0x2D,0x1A,0x49,0xFE and TX cyrfmfg_id is 0x65,0xE2,0x5E,0x55,0x4D,0xFE
+ - P[7] changes from 0x06 to 0xEE but not needed to complete the bind -> doesn't care??
+ - P[8] RF channel - 1 (on packets type 0x03)
+ - P[9] 0x00 unchanged??
+ - P[10] needs to be set to 0x01 to complete the bind -> normal packet P[0]??
+ - P[11] unchanged ?? -> no bind if set to 0x00 or 0x81
+ - P[12] unchanged ?? -> no bind if set to 0x05 or 0x86
+ - P[13] changes from 0x06 to 0x05 but not needed to complete the bind -> doesn't care??
+ - P[14..15]=0x00 unchanged??
 
-Bind phase 2 (looks like normal mode?)
-CHANNEL:	0x05
-SOP_CODE:	0xA1	0x78	0xDC	0x3C	0x9E	0x82	0xDC	0x3C
-CRC_SEED_LSB:	0x1B
-CRC_SEED_MSB:	0x3F
-RX2:	0x03	0x4A	0xA3	0x2D	0x1A	0x49	0xFE	0x06	0x00	0x00	0x02	0x01	0x06	0x06	0x00	0x00
-TX2:	0x01	0x65	0x01	0xF4	0x03	0xE7	0x02	0x08	0x00	0x00	0x01	0x01	0x02	0xEE	0x00	0x00
-Note: TX2 is nearly a normal packet at the exception of the 2nd byte equal to cyrfmfg_id[0]
-
-Bind phase 3 (check?)
+Packets 0x03: Which RF channel
 CHANNEL:	0x22
 SOP_CODE:	0x97	0xE5	0x14	0x72	0x7F	0x1A	0x14	0x72
 CRC_SEED_LSB:	0xA5
 CRC_SEED_MSB:	0xA5
-RX3:	0x04	0x4A	0xA3	0x2D	0x1A	0x49	0xFE	0x06	0x00	0x00	0x02	0x01	0x06	0x06	0x00	0x00
+RX:	0x03	0x4A	0xA3	0x2D	0x1A	0x49	0xFE	0x06	0x00	0x00	0x02	0x01	0x06	0x06	0x00	0x00
+TX:	0x03	0x65	0xE2	0x5E	0x55	0x4D	0xFE	0xEE	0x0E	0x00	0x01	0x01	0x06	0x05	0x00	0x00
+ - P[8] RF channel - 1
 
-Switch to normal mode
+Packets 0x04: unknown
+RX: 0x04	0x4A	0xA3	0x2D	0x1A	0x49	0xFE	0x06	0x00	0x00	0x02	0x01	0x06	0x06	0x00	0x00
+
+Packets 0x01: Normal mode
 CHANNEL: 	0x05
 SOP_CODE:	0xA1	0x78	0xDC	0x3C	0x9E	0x82	0xDC	0x3C
 CRC_SEED_LSB:	0x1B
 CRC_SEED_MSB:	0x3F
 TX3:	0x01	0x00	0x02	0xA8	0x03	0xE7	0x02	0x08	0x00	0x00	0x01	0x01	0x02	0xEE	0x00	0x00
+
+CRC_SEED:
+TX ID: \x65\xE2\x5E\x55\x4D\xFE
+RX ID: \x4A\xA3\x2D\x1A\x49\xFE CRC 0x1B 0x3F => CRC: 65-4A=1B E2-A3=3F
+RX ID: \x4B\xA3\x2D\x1A\x49\xFE CRC 0x1A 0x3F => CRC: 65-4B=1A E2-A3=3F
+RX ID: \x00\x00\x2D\x1A\x49\xFE CRC 0x65 0xE2 => CRC: 65-00=65 E2-00=E2
+RX ID: \x00\xFF\x2D\x1A\x49\xFE CRC 0x65 0xE3 => CRC: 65-00=65 E2-FF=E3
+RX ID: \xFF\x00\x2D\x1A\x49\xFE CRC 0x66 0xE2 => CRC: 65-FF=66 E2-00=E2
 */
+/*
+RX1: 02 4A A3 2D 1A 49 FE 06 00 00 02 01 06 06 00 00
+SOP: A1 78 DC 3C 9E 82 DC 3C
+RX2: 02 49 AC 4F 55 4D FE 05 00 00 02 01 06 06 00 00
+SOP: 5A CC AE 46 B6 31 AE 46
+RX3: 02 CA F3 62 55 4D FE 03 00 00 02 01 06 06 00 00
+SOP: 66 CD 7C 50 DD 26 7C 50
+
+Dump of SOP Codes:
+00: 3C 37 CC 91 E2 F8 CC 91 => bind
+01: 9B C5 A1 0F AD 39 A2 0F
+02: EF 64 B0 2A D2 8F B1 2A
+03: 66 CD 7C 50 DD 26 7C 50
+04: 5C E1 F6 44 AD 16 F6 44
+05: 5A CC AE 46 B6 31 AE 46
+06: A1 78 DC 3C 9E 82 DC 3C
+07: B9 8E 19 74 6F 65 18 74
+08: DF B1 C0 49 62 DF C1 49
+09: 97 E5 14 72 7F 1A 14 72 => check
+10: 82 C7 90 36 21 03 FF 17
+11: E2 F8 CC 91 3C 37 CC 91 => bind 4 bytes group swapped
+12: AD 39 A2 0F 9B C5 A1 0F => 01 4 bytes group swapped
+13: D2 8F B1 2A EF 64 B0 2A => 02 4 bytes group swapped
+14: DD 26 7C 50 66 CD 7C 50 => 03 4 bytes group swapped
+...
+19: 62 DF C1 49 DF B1 C0 49 => 08 4 bytes group swapped
+20: 00 00 00 33 DE AD BA BE ??over??
+*/
+
 #endif

Multiprotocol/Tiger_nrf24l01.ino

@@ -1,163 +0,0 @@
-/*
- This project is free software: you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation, either version 3 of the License, or
- (at your option) any later version.
-
-Multiprotocol is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- GNU General Public License for more details.
-
- You should have received a copy of the GNU General Public License
- along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
- */
-// Compatible with Tiger Drone 1400782.
-
-#if defined(TIGER_NRF24L01_INO)
-
-#include "iface_xn297.h"
-
-#define TIGER_FORCE_ID
-
-#define TIGER_INITIAL_WAIT    500
-#define TIGER_PACKET_PERIOD   3940
-#define TIGER_RF_NUM_CHANNELS 4
-#define TIGER_BIND_RF_NUM_CHANNELS 8
-#define TIGER_PAYLOAD_SIZE    16
-#define TIGER_BIND_COUNT	  761		//3sec
-
-
-static uint8_t __attribute__((unused)) TIGER_convert_channel(uint8_t num)
-{
-	uint8_t val=convert_channel_8b(num);
-	// 7F..01=left, 00=center, 80..FF=right
-	if(val==0x80)
-		val=0;				// 0
-	else
-		if(val>0x80)
-			val--;			// 80..FE
-		else
-		{
-			val=0x80-val;	// 80..01
-			if(val==0x80)
-				val--;		// 7F..01
-		}
-	return val;
-}
-
-static void __attribute__((unused)) TIGER_send_packet()
-{
-	if(IS_BIND_DONE)
-	{
-		//Channels
-		packet[0]=convert_channel_8b(THROTTLE);		// 00..FF
-		packet[1]=TIGER_convert_channel(RUDDER);	// 7F..01=left, 00=center, 80..FF=right
-		packet[2]=TIGER_convert_channel(ELEVATOR);	// 7F..01=down, 00=center, 80..FF=up
-		packet[3]=TIGER_convert_channel(AILERON);	// 7F..01=left, 00=center, 80..FF=right
-		//Flags
-		packet[14]= GET_FLAG(CH5_SW, 0x04)			//FLIP
-				  | GET_FLAG(CH6_SW, 0x10);			//LIGHT
-	}
-	//Check
-	crc8=0;
-	for(uint8_t i=0;i<TIGER_PAYLOAD_SIZE-1;i++)
-		crc8+=packet[i];
-	packet[TIGER_PAYLOAD_SIZE-1]=crc8;
-
-	//Hopping frequency
-	XN297_Hopping(hopping_frequency_no>>1);
-	hopping_frequency_no++;
-	if(IS_BIND_IN_PROGRESS)
-	{
-		if(hopping_frequency_no>=2*TIGER_BIND_RF_NUM_CHANNELS)
-			hopping_frequency_no=0;
-	}
-	else
-	{
-		if(hopping_frequency_no>=2*(TIGER_BIND_RF_NUM_CHANNELS+TIGER_RF_NUM_CHANNELS))
-			hopping_frequency_no=2*TIGER_BIND_RF_NUM_CHANNELS;
-	}
-
-	//Send
-	XN297_SetPower();
-	XN297_SetTxRxMode(TX_EN);
-	XN297_WritePayload(packet, TIGER_PAYLOAD_SIZE);
-}
-
-static void __attribute__((unused)) TIGER_RF_init()
-{
-	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_1M);
-	XN297_SetTXAddr((uint8_t *)"\x68\x94\xA6\xD5\xC3", 5);
-}
-
-static void __attribute__((unused)) TIGER_initialize_txid()
-{
-#ifdef TIGER_FORCE_ID
-	rx_tx_addr[0]=0x64;
-	rx_tx_addr[1]=0x39;
-	rx_tx_addr[2]=0x12;
-	rx_tx_addr[3]=0x00;
-	rx_tx_addr[4]=0x00;
-	memcpy(hopping_frequency,"\x0E\x39\x1C\x07\x24\x3E\x2B\x47",TIGER_BIND_RF_NUM_CHANNELS);
-	memcpy(&hopping_frequency[TIGER_BIND_RF_NUM_CHANNELS],"\x36\x41\x37\x4E",TIGER_RF_NUM_CHANNELS);
-#endif
-	//prepare bind packet
-	memset(&packet[0], 0x00, 4);
-	memset(&packet[4], 0x40, 10);
-	memcpy(&packet[7], rx_tx_addr, 5);
-	packet[14]=0xC0;
-}
-
-uint16_t TIGER_callback()
-{
-	#ifdef MULTI_SYNC
-		telemetry_set_input_sync(TIGER_PACKET_PERIOD);
-	#endif
-	if(bind_counter)
-		if(--bind_counter==0)
-		{
-			BIND_DONE;
-			XN297_SetTXAddr((uint8_t *)"\x49\xA6\x83\xEB\x4B", 5);
-		}
-	TIGER_send_packet();
-	return TIGER_PACKET_PERIOD;
-}
-
-void TIGER_init()
-{
-	BIND_IN_PROGRESS;	// autobind protocol
-	TIGER_initialize_txid();
-	TIGER_RF_init();
-	hopping_frequency_no = 0;
-	bind_counter=TIGER_BIND_COUNT;
-}
-
-#endif
-/*Bind
-- RF setup: 1Mbps, scrambled, CRC
-- TX addr: 0x68 0x94 0xA6 0xD5 0xC3
-- 8 RF channels: 0x0E 0x39 0x1C 0x07 0x24 0x3E 0x2B 0x47
-- 2 packets per RF channel, 3940µs between packets
-- payload 16 bytes: 0x00 0x00 0x00 0x00 0x40 0x40 0x40 0x64 0x39 0x12 0x00 0x00 0x40 0x40 0xC0 0xAF
-- payload[15]=sum of payload[0..14]
-- the only difference with normal packets is the payload[14]=0xC0
-- ??? payload[7..11] TX ID ???
-
-Normal
-- RF setup: 1Mbps
-- TX addr: 0x49 0xA6 0x83 0xEB 0x4B
-- 4 RF channels: 0x36 0x41 0x37 0x4E
-- 2 packets per RF channel, 3940µs between packets
-- payload 16 bytes: 0x00 0x00 0x00 0x00 0x40 0x40 0x40 0x64 0x39 0x12 0x00 0x00 0x40 0x40 0x00 0xEF
-- payload[15]=sum of payload[0..14]
-- throttle is on payload[0] 00..FF
-- rudder is on payload[1] 00=center, 80..FF=right, 01..7F=left
-- elevator is on payload[2] 00=center, 80..FF=up, 01..7F=down
-- aileron is on payload[3] 00=center, 80..FF=right, 01..7F=left
-- trims payload[4..6]
-- ??? payload[7..11] TX ID ???
-- ??? payload[12..13] ???
-- flip is on payload[14] and flag 0x04
-- light is on payload[14] and flag 0x10
-*/

Multiprotocol/V911S_ccnrf.ino

@@ -35,6 +35,8 @@
 // flags going to packet[2]
 #define	V911S_FLAG_CALIB	0x01
 #define A220_FLAG_6G3D		0x04
+#define A280_FLAG_6GSENIOR	0x08
+#define A280_FLAG_LIGHT		0x20
 
 static void __attribute__((unused)) V911S_send_packet()
 {
@@ -74,7 +76,9 @@ static void __attribute__((unused)) V911S_send_packet()
 		{
 			packet[ 1]=GET_FLAG(!CH6_SW,E119_FLAG_EXPERT)	// short  press on left button
 					  |GET_FLAG( CH5_SW,E119_FLAG_CALIB);	// short  press on right button
-			packet[ 2]=GET_FLAG( CH7_SW,A220_FLAG_6G3D);	// short  press on right button
+			packet[ 2]=GET_FLAG( CH7_SW,A220_FLAG_6G3D)	// short  press on right button
+					  |GET_FLAG( CH8_SW,A280_FLAG_6GSENIOR)    // -100% - 6G, +100% - Senior mode (turn off gyro)
+					  |GET_FLAG( CH9_SW,A280_FLAG_LIGHT);	// cycle the light through on-flash-off when the CH9 value is changed from -100% to 100% 
 		}
 			
 		//packet[3..6]=trims TAER signed

Multiprotocol/Validate.h

@@ -330,9 +330,9 @@
 	#undef	POTENSIC_NRF24L01_INO
 	#undef	PROPEL_NRF24L01_INO
 	#undef	REALACC_NRF24L01_INO
+	#undef	SGF22_NRF24L01_INO
 	#undef	SHENQI_NRF24L01_INO
 	#undef	SYMAX_NRF24L01_INO
-	#undef	TIGER_NRF24L01_INO
 	#undef	V2X2_NRF24L01_INO
 	#undef	V761_NRF24L01_INO
 	#undef	XERALL_NRF24L01_INO
@@ -340,6 +340,8 @@
 	#undef	ZSX_NRF24L01_INO
 #endif
 #if ( not defined(CC2500_INSTALLED) && not defined(NRF24L01_INSTALLED) ) || defined MULTI_EU
+	#undef	BLUEFLY_CCNRF_INO
+	#undef	BUMBLEB_CCNRF_INO
 	#undef	GD00X_CCNRF_INO
 	#undef	KF606_CCNRF_INO
 	#undef	MJXQ_CCNRF_INO
@@ -351,6 +353,9 @@
 	#undef	V911S_CCNRF_INO
 	#undef	XK_CCNRF_INO
 #endif
+#if not defined(DSM_CYRF6936_INO)
+	#undef	LOSI_CYRF6936_INO
+#endif
 #if not defined(STM32_BOARD)
 	//RF2500 emulation does not work on atmega...
 	#undef	E010R5_CYRF6936_INO
@@ -363,6 +368,72 @@
 	#undef FRSKYR9_SX1276_INO
 #endif
 
+#ifdef MULTI_AIR
+	#undef	JOYSWAY_A7105_INO
+	//#undef	KYOSHO_A7105_INO
+	//#undef	PELIKAN_A7105_INO
+	#undef	LOSI_CYRF6936_INO		//Need DSM to be enabled
+	#undef	TRAXXAS_CYRF6936_INO
+	#undef	KYOSHO2_NRF24L01_INO
+	#undef	MOULDKG_NRF24L01_INO
+	#undef	SHENQI_NRF24L01_INO
+#endif
+
+#ifdef MULTI_SURFACE
+	#undef	BUGS_A7105_INO
+	#undef	HEIGHT_A7105_INO
+	#undef	HUBSAN_A7105_INO
+	#undef	E010R5_CYRF6936_INO
+	#undef	E01X_CYRF6936_INO
+	#undef	E129_CYRF6936_INO
+	#undef	J6PRO_CYRF6936_INO
+	#undef	SCORPIO_CYRF6936_INO
+	#undef	E016HV2_CC2500_INO
+	#undef	ESKY150V2_CC2500_INO
+	#undef	IKEAANSLUTA_CC2500_INO  // This is mostly a "for-fun" kind of a thing, not needed for most users
+	#undef	SKYARTEC_CC2500_INO
+	#undef	REDPINE_CC2500_INO
+	#undef	BAYANG_NRF24L01_INO
+	#undef	BAYANG_RX_NRF24L01_INO
+	#undef	BUGSMINI_NRF24L01_INO
+	#undef	CABELL_NRF24L01_INO
+	#undef	CFLIE_NRF24L01_INO
+	#undef	CG023_NRF24L01_INO
+	#undef	CX10_NRF24L01_INO
+	#undef	DM002_NRF24L01_INO
+	#undef	E016H_NRF24L01_INO
+	#undef	ESKY_NRF24L01_INO
+	#undef	ESKY150_NRF24L01_INO
+	#undef	FQ777_NRF24L01_INO
+	#undef	FX_NRF24L01_INO
+	#undef	FY326_NRF24L01_INO
+	#undef	GW008_NRF24L01_INO
+	#undef	HONTAI_NRF24L01_INO
+	#undef	H8_3D_NRF24L01_INO
+	#undef	JJRC345_NRF24L01_INO
+	#undef	KN_NRF24L01_INO
+	#undef	LOLI_NRF24L01_INO
+	#undef	NCC1701_NRF24L01_INO
+	#undef	POTENSIC_NRF24L01_INO
+	#undef	PROPEL_NRF24L01_INO
+	#undef	REALACC_NRF24L01_INO
+	#undef	SGF22_NRF24L01_INO
+	#undef	SYMAX_NRF24L01_INO
+	#undef	V761_NRF24L01_INO
+	#undef	XERALL_NRF24L01_INO
+	#undef	YD717_NRF24L01_INO
+	#undef	ZSX_NRF24L01_INO
+	#undef	GD00X_CCNRF_INO
+	#undef	KF606_CCNRF_INO
+	#undef	MJXQ_CCNRF_INO
+	#undef	MT99XX_CCNRF_INO
+	#undef	OMP_CCNRF_INO
+	#undef	Q303_CCNRF_INO
+	#undef	Q90C_CCNRF_INO
+	#undef	SLT_CCNRF_INO
+	#undef	V911S_CCNRF_INO
+#endif
+
 //OpenTX 2.3.x issue
 #if defined (FRSKYD_CC2500_INO) || defined(FRSKYV_CC2500_INO) || defined(FRSKYX_CC2500_INO)
 	#define	FRSKYX_CC2500_INO

Multiprotocol/XK_ccnrf.ino

@@ -28,11 +28,18 @@ Multiprotocol is distributed in the hope that it will be useful,
 #define XK_BIND_COUNT		750					//3sec
 
 static uint16_t __attribute__((unused)) XK_convert_channel(uint8_t num)
+{
+	uint16_t val;
+	
+	if(sub_protocol != XK_CARS)
 	{
 		// Introduce deadband on all channels to prevent twitching
 		//debug("val:%d",val);
-	uint16_t val=convert_channel_8b_limit_deadband(num,0x00,0x80, 0xFF, 40)<<2;
+		val=convert_channel_8b_limit_deadband(num,0x00,0x80, 0xFF, 40)<<2;
 		//debugln(",%d",val);
+	}
+	else
+		val=convert_channel_16b_limit(num,0x00,0x3FF);
 	
 	// 1FF..01=left, 00=center, 200..3FF=right
 	if(val==0x200)
@@ -94,7 +101,9 @@ static void __attribute__((unused)) XK_send_packet()
 		packet[11]  = GET_FLAG(CH8_SW ,0x03)	// 3D/6G momentary switch
 					 |GET_FLAG(CH6_SW ,0x40);	// Take off momentary switch
 		packet[14]  = GET_FLAG(CH9_SW ,0x01)	// Photo momentary switch
-					 |GET_FLAG(CH10_SW,0x2);	// Video momentary switch
+					 |GET_FLAG(CH10_SW,0x02)	// Video momentary switch
+					 |GET_FLAG(CH11_SW,0x04)	// Flip
+					 |GET_FLAG(CH12_SW,0x10);	// Light
 		//debugln("P1:%02X,P12:%02X",packet[1],packet[12]);
 	}
 
@@ -187,7 +196,7 @@ static void __attribute__((unused)) XK_initialize_txid()
 
 static void __attribute__((unused)) XK_RF_init()
 {
-	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, sub_protocol==X420 ? XN297_1M : XN297_250K);
+	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, sub_protocol==X450 ? XN297_250K : XN297_1M );
 	XN297_SetTXAddr((uint8_t*)"\x68\x94\xA6\xD5\xC3", 5);						// Bind address
 	XN297_HoppingCalib(XK_RF_BIND_NUM_CHANNELS+XK_RF_NUM_CHANNELS);				// Calibrate all channels
 }
@@ -209,6 +218,7 @@ uint16_t XK_callback()
 
 void XK_init()
 {
+	if(sub_protocol != XK_CARS)
 		BIND_IN_PROGRESS;															// Autobind protocol
 	XK_initialize_txid();
 	XK_RF_init();

Multiprotocol/_Config.h

@@ -188,10 +188,10 @@
 #define	DSM_CYRF6936_INO
 #define	DSM_RX_CYRF6936_INO
 #define	E010R5_CYRF6936_INO
-//#define	E01X_CYRF6936_INO
+#define	E01X_CYRF6936_INO
 #define	E129_CYRF6936_INO
 #define	J6PRO_CYRF6936_INO
-//#define	LOSI_CYRF6936_INO
+#define	LOSI_CYRF6936_INO		//Need DSM to be enabled
 #define	MLINK_CYRF6936_INO
 #define	SCORPIO_CYRF6936_INO
 #define	TRAXXAS_CYRF6936_INO
@@ -222,7 +222,7 @@
 #define	BAYANG_RX_NRF24L01_INO
 #define	BUGSMINI_NRF24L01_INO
 #define	CABELL_NRF24L01_INO
-//#define	CFLIE_NRF24L01_INO
+#define	CFLIE_NRF24L01_INO
 #define	CG023_NRF24L01_INO
 #define	CX10_NRF24L01_INO		//Include Q2X2 protocol
 #define	DM002_NRF24L01_INO
@@ -240,14 +240,14 @@
 #define	KN_NRF24L01_INO
 #define	KYOSHO2_NRF24L01_INO
 #define	LOLI_NRF24L01_INO
-//#define	MOULDKG_NRF24L01_INO
+#define	MOULDKG_NRF24L01_INO
 #define	NCC1701_NRF24L01_INO
 #define	POTENSIC_NRF24L01_INO
 #define	PROPEL_NRF24L01_INO
 #define	REALACC_NRF24L01_INO
+#define	SGF22_NRF24L01_INO
 #define	SHENQI_NRF24L01_INO
 #define	SYMAX_NRF24L01_INO
-#define	TIGER_NRF24L01_INO
 #define	V2X2_NRF24L01_INO
 #define	V761_NRF24L01_INO
 #define	XERALL_NRF24L01_INO
@@ -567,6 +567,8 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 		QX100
 	PROTO_BAYANG_RX
 		NONE
+	PROTO_BLUEFLY
+		NONE
 	PROTO_BUGS
 		NONE
 	PROTO_BUGSMINI
@@ -793,10 +795,13 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 		RLINK_SURFACE
 		RLINK_AIR
 		RLINK_DUMBORC
+		RLINK_RC4G
 	PROTO_SCANNER
 		NONE
 	PROTO_SCORPIO
 		NONE
+	PROTO_SGF22
+		NONE
 	PROTO_SHENQI
 		NONE
 	PROTO_SKYARTEC
@@ -810,8 +815,6 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 	PROTO_SYMAX
 		SYMAX
 		SYMAX5C
-	PROTO_TIGER
-		NONE
 	PROTO_TRAXXAS
 		RX6519
 	PROTO_V2X2
@@ -840,6 +843,7 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 	PROTO_XK
 		X450
 		X420
+		XK_CARS
 	PROTO_YD717
 		YD717
 		SKYWLKR

Multiprotocol/iface_cyrf6936.h

@@ -85,7 +85,7 @@ void CYRF_SetPower(u8 power);
 void CYRF_ConfigCRCSeed(u16 crc);
 static void CYRF_StartReceive();
 void CYRF_ConfigSOPCode(const u8 *sopcodes);
-void CYRF_ConfigDataCode(const u8 *datacodes, u8 len);
+void CYRF_ConfigDataCode(const u8 *datacodes);
 static u8 CYRF_ReadRSSI(u32 dodummyread);
 static void CYRF_ReadDataPacket(u8 dpbuffer[]); 
 void CYRF_WriteDataPacket(const u8 dpbuffer[]);

Protocols_Details.md

@@ -65,6 +65,7 @@ Protocol Name|Protocol Number|Sub_Proto 0|Sub_Proto 1|Sub_Proto 2|Sub_Proto 3|Su
 [Assan](Protocols_Details.md#ASSAN---24)|24|||||||||NRF24L01|
 [Bayang](Protocols_Details.md#BAYANG---14)|14|Bayang|H8S3D|X16_AH|IRDRONE|DHD_D4|QX100|||NRF24L01|XN297
 [Bayang RX](Protocols_Details.md#BAYANG-RX---59)|59|Multi|CPPM|||||||NRF24L01|XN297
+[BlueFly](Protocols_Details.md#BLUEFLY---95)|95|||||||||NRF24L01|
 [Bugs](Protocols_Details.md#BUGS---41)|41|||||||||A7105|
 [BugsMini](Protocols_Details.md#BUGSMINI---42)|42|BUGSMINI|BUGS3H|||||||NRF24L01|XN297
 [Cabell](Protocols_Details.md#Cabell---34)|34|Cabell_V3|C_TELEM|-|-|-|-|F_SAFE|UNBIND|NRF24L01|
@@ -130,16 +131,16 @@ CFlie|38|CFlie||||||||NRF24L01|
 [Q2X2](Protocols_Details.md#Q2X2---29)|29|Q222|Q242|Q282||||||NRF24L01|
 [Q303](Protocols_Details.md#Q303---31)|31|Q303|CX35|CX10D|CX10WD|||||NRF24L01|XN297
 [Q90C](Protocols_Details.md#Q90C---72)|72|Q90C*||||||||NRF24L01|XN297
-[RadioLink](Protocols_Details.md#RadioLink---74)|74|Surface|Air|DumboRC||||||CC2500|
+[RadioLink](Protocols_Details.md#RadioLink---74)|74|Surface|Air|DumboRC|RC4G|||||CC2500|
 [Realacc](Protocols_Details.md#Realacc---76)|76|R11||||||||NRF24L01|
 [Redpine](Protocols_Details.md#Redpine---50)|50|FAST|SLOW|||||||NRF24L01|XN297
 [Scanner](Protocols_Details.md#Scanner---54)|54|||||||||CC2500|
 [Scorpio](Protocols_Details.md#Scorpio---94)|94|||||||||CYRF6936|
+[SGF22](Protocols_Details.md#SGF22---97)|97|SGF22||||||||NRF24L01|XN297
 [Shenqi](Protocols_Details.md#Shenqi---19)|19|Shenqi||||||||NRF24L01|LT8900
 [Skyartec](Protocols_Details.md#Skyartec---68)|68|||||||||CC2500|CC2500
 [SLT](Protocols_Details.md#SLT---11)|11|SLT_V1|SLT_V2|Q100|Q200|MR100||||NRF24L01|CC2500
 [SymaX](Protocols_Details.md#Symax---10)|10|SYMAX|SYMAX5C|||||||NRF24L01|
-[Tiger](Protocols_Details.md#Tiger---61)|61|||||||||NRF24L01|XN297
 [Traxxas](Protocols_Details.md#Traxxas---43)|43|6519 RX||||||||CYRF6936|
 [V2x2](Protocols_Details.md#V2X2---5)|5|V2x2|JXD506|MR101||||||NRF24L01|
 [V761](Protocols_Details.md#V761---48)|48|3CH|4CH|TOPRC||||||NRF24L01|XN297
@@ -148,7 +149,7 @@ CFlie|38|CFlie||||||||NRF24L01|
 [WFLY2](Protocols_Details.md#WFLY2---79)|79|RF20x||||||||A7105|
 [WK2x01](Protocols_Details.md#WK2X01---30)|30|WK2801|WK2401|W6_5_1|W6_6_1|W6_HEL|W6_HEL_I|||CYRF6936|
 [XERALL](Protocols_Details.md#XERALL---91)|91|Tank||||||||NRF24L01|XN297
-[XK](Protocols_Details.md#XK---62)|62|X450|X420|||||||NRF24L01|XN297
+[XK](Protocols_Details.md#XK---62)|62|X450|X420|Cars||||||NRF24L01|XN297
 [YD717](Protocols_Details.md#YD717---8)|8|YD717|SKYWLKR|SYMAX4|XINXUN|NIHUI||||NRF24L01|
 [ZSX](Protocols_Details.md#ZSX---52)|52|280||||||||NRF24L01|XN297
 * "*" Sub Protocols designated by * suffix are using a XN297L@250kbps which will be emulated by default with the NRF24L01. If option (freq tune) is diffrent from 0, the CC2500 module (if installed) will be used instead. Each specific sub protocol has a more detailed explanation.
@@ -325,7 +326,11 @@ CH1|CH2|CH3|CH4
 ## Kyosho - *73*
 
 ### Sub_protocol FHSS - *0*
-Surface protocol called FHSS introduced in 2017. Transmitters: KT-531P, KT-431PT...
+Surface protocol called FHSS introduced in 2017. Transmitter: KT-531P. Models: Mini-Z.
+
+Surface protocol called Syncro. TX: KT-331, RX: KR-331
+
+Extended limits supported
 
 CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12|CH13|CH14
 ---|---|---|---|---|---|---|---|---|----|----|----|----|----
@@ -358,11 +363,11 @@ Models: TX: CADET 4 LITE
 **Only 1 frequency hopping table**
 
 ### Sub_protocol SCX24 - *2*
-TX: Axial AX-4 2.4GHz transmitter and Panda Hobby 3CH Smart Radio 2.4GHz (MT-305A)
+TX: Axial AX-4 2.4GHz transmitter, HPI TF-41 and Panda Hobby 3CH Smart Radio 2.4GHz (MT-305A)
 
-Models: Axial SCX24: Deadbolt, Jeep Wranger Rubicon, Chevrolet 1967 C10, B-17 Betty and Panda Hobby: Tetra K1, X1, X2
+Models: Axial SCX24: Deadbolt, Jeep Wranger Rubicon, Chevrolet 1967 C10, B-17 Betty, HPI RF-50 and Panda Hobby: Tetra K1, X1, X2
 
-**Only 2 frequency hopping tables**
+**Only 4 frequency hopping tables**
 
 Extended limits supported
 
@@ -616,10 +621,18 @@ Calib is the same as the original radio with both sticks down and to the left in
 Models: Eachine E129/E130 and Twister Ninja 250
 
 ### Sub_protocol C186 - *1*
-Models: C186/E120, C127/E110, K127, C159
+Models: C186/E120, C127/E110, K127, C159, C189, C129v2
 
 The FC of the heli seems to store the trims Trim A/E/R=CH7..9. If you use these trims, make sure to center them after powering off the heli or they will be added to the previous trims and over correct.
 
+CH10|CH11
+---|---
+Loop|Flip
+
+Loop: circular flight on the C159 (others?)
+
+Flip: flip/aerobatic on the C129v2 (others?)
+
 ## J6Pro - *22*
 
 CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12
@@ -629,8 +642,6 @@ A|E|T|R|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12
 ## Losi - *89*
 TX: LSR-3000
 
-**Only 1 ID available**. More IDs can be added if you dump your original TX.
-
 Extended limits supported
 
 CH1|CH2|CH3
@@ -989,6 +1000,17 @@ Telemetry: RX_RSSI (for the original value add -256), TX_RSSI, TX_QLY (0..100%)
 ### Sub_protocol DumboRC - *2*
 Compatible RXs: X6/X6F/X6FG
 
+### Sub_protocol RC4G - *3*
+Compatible RXs: R4EH-G(/R4EH-H)
+
+CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9
+---|---|---|---|---|---|---|---|---
+CH1|CH2|CH3|CH4|CH5|FS_CH1|FS_CH2|FS_CH3|FS_CH4
+
+FS=FailSafe
+
+CH5 is driven by CH3 on the original TX, gyro sensibility?
+
 ## Futaba - *21*
 Also called SFHSS depending on radio version.
 
@@ -1024,6 +1046,17 @@ If a CC2500 is installed it will be used for all the below protocols. Option in
 
 If only a NRF24L01 is installed then these protocols might be problematic because they are using the XN297L emulation with a transmission speed of 250kbps which doesn't work very well with every NRF24L01, this is an hardware issue with the authenticity and accuracy of the components.
 
+## BLUEFLY - *95*
+Model: HP100
+
+CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8
+---|---|---|---|---|---|---|---
+A|E|T|R|CH5|CH6|CH7|CH8
+
+TRIM: either use this channel for trim only or add a mixer with aileron to increase the roll rate.
+
+RATE: -100% high rate, +100% low rate
+
 ## GD00X - *47*
 Model: GD005 C-17 Transport, GD006 DA62 and ZC-Z50
 
@@ -1370,18 +1403,14 @@ Models: WLtoys V911S, XK A110
 ### Sub_protocol E119 - *1*
 Models: Eachine E119, JJRC W01-J3, XK A220 P-40, XK A800 R2, F959S R2, A160 R2, A280
 
-CH1|CH2|CH3|CH4|CH5|CH6|CH7
----|---|---|---|---|---|---
-A|E|T|R|CALIB|RATE|6G_3D
+CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9
+---|---|---|---|---|---|---|---|---
+A|E|T|R|CALIB|RATE|6G_3D|6GSENIOR|LIGHT
+
+A280 -> 6GSENIOR: -100% - 6G, +100% - Senior mode (turn off gyro), LIGHT: cycle the light through on-flash-off when the CH9 value is changed from -100% to 100%
 
 ## XK - *62*
 
-CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10
----|---|---|---|---|---|---|---|---|----
-A|E|T|R|Flight_modes|Take_off|Emerg stop|3D/6G|Picture|Video
-
-Flight_modes: -100%=M-Mode, 0%=6G-Mode, +100%=V-Mode. CH6-CH10 are mementary switches.
-
 CC2500: only X450 is supported.
 
 ### Sub_protocol X450 - *0*
@@ -1391,9 +1420,31 @@ If a CC2500 is installed it will be used for this sub protocol. Option in this c
 
 If only a NRF24L01 is installed then this sub protocol might be problematic because it is using the xn297L emulation with a transmission speed of 250kbps which doesn't work very well with every NRF24L01, this is an hardware issue with the authenticity and accuracy of the components.
 
+CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10
+---|---|---|---|---|---|---|---|---|----
+A|E|T|R|Flight_modes|Take_off|Emerg stop|3D/6G|Picture|Video
+
+Flight_modes: -100%=M-Mode, 0%=6G-Mode, +100%=V-Mode. CH6-CH10 are mementary switches.
+
 ### Sub_protocol X420 - *1*
 Models: XK X420/X520 (TX=X4)
 
+CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10
+---|---|---|---|---|---|---|---|---|----
+A|E|T|R|Flight_modes|Take_off|Emerg stop|3D/6G|Picture|Video
+
+Flight_modes: -100%=M-Mode, 0%=6G-Mode, +100%=V-Mode. CH6-CH10 are mementary switches.
+
+Model: Tiger Drone 1400782
+
+CH1|CH2|CH3|CH4|CH11|CH12
+---|---|---|---|---|---
+A|E|T|R|FLIP|LIGHT
+
+### Sub_protocol Cars - *2*
+Models: WLtoys cars 284131/284161/284010/124016/124017/144010 and Eachine EAT14
+
+
 ***
 # NRF24L01 RF Module
 
@@ -1420,13 +1471,13 @@ Channels 14 and 15 (ANAAUX1 and ANAAUX2) only available with analog aux channel
 ### Sub_protocol BAYANG - *0*
 Models: Eachine H8(C) mini, BayangToys X6/X7/X9, JJRC JJ850, Floureon H101 ...
 
-Option=0 -> normal Bayang protocol
+Option=0 or Telemetry = Off -> normal Bayang protocol
 
-Option=1 -> enable telemetry with [Silverxxx firmware](https://github.com/silver13/H101-acro/tree/master). Value returned to the TX using FrSkyD Hub are RX RSSI, TX RSSI, A1=uncompensated battery voltage (set the ratio to 5.0 and adjust with offset), A2=compensated battery voltage (set the ratio to 5.0 and adjust with offset) and if supported AccX=P, AccY=I, ACCZ=D (which you can rename after the sensors discovery)
+Option=1 or Telemetry = On -> enable telemetry with [Silverxxx firmware](https://github.com/silver13/H101-acro/tree/master). Value returned to the TX using FrSkyD Hub are RX RSSI, TX RSSI, A1=uncompensated battery voltage (set the ratio to 5.0 and adjust with offset), A2=compensated battery voltage (set the ratio to 5.0 and adjust with offset) and if supported AccX=P, AccY=I, ACCZ=D (which you can rename after the sensors discovery)
 
-Option=2 -> enable analog aux channels with [NFE Silverware firmware](https://github.com/NotFastEnuf/NFE_Silverware). Two otherwise static bytes in the protocol overridden to add two 'analog' (non-binary) auxiliary channels.
+Option=2 or Telemetry = Off+AUX -> enable analog aux channels with [NFE Silverware firmware](https://github.com/NotFastEnuf/NFE_Silverware). Two otherwise static bytes in the protocol overridden to add two 'analog' (non-binary) auxiliary channels.
 
-Option=3 -> both Silverware telemetry and analog aux channels enabled.
+Option=3 or Telemetry = On+AUX-> both Silverware telemetry and analog aux channels enabled.
 
 ### Sub_protocol H8S3D - *1*
 Model: H8S 3D
@@ -1647,13 +1698,13 @@ Only 8 TX IDs available
 Model: FX620 SU35
 
 ### Sub_protocol 9630 - *2*
-Model: FX9630 and QIDI-550
+Model: FX9630, FX9603 and QIDI-550
 
 CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9
 ---|---|---|---|---|---|---|---|---
 A|E|T|R|RATE|GYRO|TrimR|TrimA|TrimE
 
-FX9630 Gyro: -100%=6G small throw, 0%=6G large throw, +100%=3D
+FX9630 and FX9603 Gyro: -100%=6G small throw, 0%=6G large throw, +100%=3D
 
 QIDI-550 Gyro: -100%=3D, 0%=6G, +100%=Torque
 
@@ -1731,9 +1782,9 @@ CH1|CH2|CH3|CH4|CH5
 | | |T|R|AUX
 
 ## KN - *9*
-CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11
----|---|---|---|---|---|---|---|---|----|----
-A|E|T|R|DR|THOLD|IDLEUP|GYRO|Ttrim|Atrim|Etrim
+CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12|CH13
+---|---|---|---|---|---|---|---|---|----|----|----|----
+A|E|T|R|DR|THOLD|IDLEUP|GYRO|Ttrim|Atrim|Etrim|Rtrim|HoverDebugging
 
 Dual Rate: +100%=full range, Throttle Hold: +100%=hold, Idle Up: +100%=3D, GYRO: -100%=6G, +100%=3G
 
@@ -1910,6 +1961,15 @@ A|E|T|R|FLIP|LIGHT|CALIB|HLESS|RTH|UNK
 ### Sub_protocol FAST - *0*
 ### Sub_protocol SLOW - *1*
 
+## SGF22 - *97*
+Autobind protocol
+
+Model: SGF22
+
+CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9
+---|---|---|---|---|---|---|---|---
+A|E|T|R|MODE|FLIP|LIGHT|PHOTO|VIDEO
+
 ## Shenqi - *19*
 Autobind protocol
 
@@ -1942,7 +2002,7 @@ CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11
 A|E|T|R|FLIP|LIGHT|PICTURE|VIDEO|HEADLESS|MAG_CAL_X|MAG_CAL_Y
 
 ### Sub_protocol V2x2 - *0*
-Models: WLToys V202/252/272, JXD 385/388, JJRC H6C, Yizhan Tarantula X6 ...
+Models: WLToys V202/252/272/A959/K969/K979/K989/K999, JXD 385/388, JJRC H6C, Yizhan Tarantula X6 ...
 
 PICTURE: also automatic Missile Launcher and Hoist in one direction
 
@@ -1972,15 +2032,6 @@ AUTO: Land=-100% Takeoff=+100%
 
 The model can work with a none centered throttle.
 
-## Tiger - *61*
-Autobind protocol
-
-**Only 1 ID**
-
-CH1|CH2|CH3|CH4|CH5|CH6
----|---|---|---|---|---
-A|E|T|R|FLIP|LIGHT
-
 ## V761 - *48*
 
 Gyro: -100%=Beginner mode (Gyro on, yaw and pitch rate limited), 0%=Mid Mode ( Gyro on no rate limits), +100%=Mode Expert Gyro off
@@ -1991,8 +2042,6 @@ Flip: momentary switch: hold flip(+100%), indicate flip direction with Ele or Ai
 
 RTN_ACT and RTN: -100% disable, +100% enable
 
-If the model (newest versions) sends telemetry then the battery status ok/empty is in A1 (4.4V -> 2.2V), RSSI equals to 100 means that 100% of the telem packets have been received.
-
 ### Sub_protocol 3CH - *0*
 Models: Volantex V761-1, V761-3 and may be others
 
@@ -2003,6 +2052,8 @@ CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9
 ### Sub_protocol 4CH - *1*
 Models: Volantex V761-4+ and Eachine P51-D, F4U, F22 and may be others
 
+If the model (761-11 and above) sends telemetry then the battery status ok/empty is in A1 (4.4V -> 2.2V) and RSSI gets a dummy value of 100.
+
 CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9
 ---|---|---|---|---|---|---|---|---
 A|E|T|R|GYRO|CALIB|FLIP|RTN_ACT|RTN

buildroot/bin/buildFunctions

@@ -86,6 +86,7 @@ buildEachRFModule() {
 buildReleaseFiles(){
     if [[ "$BOARD" =~ ":avr:multixmega32d4" ]]; then
         build_release_orx;
+        build_release_extras;
     elif [[ "$BOARD" =~ ":avr:multiatmega328p:bootloader=none" ]]; then
         build_release_avr_noboot;
     elif [[ "$BOARD" =~ ":avr:multiatmega328p:bootloader=optiboot" ]]; then

buildroot/bin/build_release_avr_noboot

@@ -22,6 +22,7 @@ mv build/Multiprotocol.ino.bin ./binaries/mm-avr-usbasp-aetr-CC2500-inv-v$MULTI_
 printf "\e[33;1mBuilding mm-avr-usbasp-aetr-CYRF6936-inv-v$MULTI_VERSION.bin\e[0m\n";
 opt_disable $ALL_PROTOCOLS;
 opt_enable $CYRF6936_PROTOCOLS;
+opt_disable E01X_CYRF6936_INO LOSI_CYRF6936_INO
 buildMulti;
 exitcode=$((exitcode+$?));
 mv build/Multiprotocol.ino.bin ./binaries/mm-avr-usbasp-aetr-CYRF6936-inv-v$MULTI_VERSION.bin;

buildroot/bin/build_release_avr_optiboot

@@ -22,6 +22,7 @@ mv build/Multiprotocol.ino.bin ./binaries/mm-avr-txflash-aetr-CC2500-inv-v$MULTI
 printf "\e[33;1mBuilding mm-avr-txflash-aetr-CYRF6936-inv-v$MULTI_VERSION.bin\e[0m\n";
 opt_disable $ALL_PROTOCOLS;
 opt_enable $CYRF6936_PROTOCOLS;
+opt_disable E01X_CYRF6936_INO LOSI_CYRF6936_INO
 buildMulti;
 exitcode=$((exitcode+$?));
 mv build/Multiprotocol.ino.bin ./binaries/mm-avr-txflash-aetr-CYRF6936-inv-v$MULTI_VERSION.bin; 

buildroot/bin/build_release_extras

@@ -0,0 +1,15 @@
+#!/usr/bin/env bash
+
+source ./buildroot/bin/buildFunctions;
+exitcode=0;
+
+printf "\e[33;1mPackaging ancilliary files for v$MULTI_VERSION\e[0m\n";
+cp Multiprotocol/Multi.txt ./binaries/Multi.txt;
+
+mkdir -p SCRIPTS/TOOLS;
+cp -r Lua_scripts/* SCRIPTS/TOOLS/;
+find SCRIPTS/TOOLS -type f -name "*.md" -delete
+
+zip -q -r ./binaries/MultiLuaScripts.zip SCRIPTS/TOOLS/*;
+
+exit $exitcode;

buildroot/bin/build_release_orx

@@ -16,11 +16,4 @@ buildMulti;
 exitcode=$((exitcode+$?));
 mv build/Multiprotocol.ino.bin ./binaries/mm-orangerx-aetr-blue-inv-v$MULTI_VERSION.bin;
 
-printf "\e[33;1mPackaging ancilliary files for v$MULTI_VERSION\e[0m\n";
-cp Multiprotocol/Multi.txt ./binaries/Multi.txt;
-mkdir -p SCRIPTS/TOOLS;
-cp Lua_scripts/*.lua SCRIPTS/TOOLS/;
-cp Lua_scripts/*.txt SCRIPTS/TOOLS/;
-zip -q ./binaries/MultiLuaScripts.zip SCRIPTS/TOOLS/*;
-
 exit $exitcode;

buildroot/bin/build_release_stm32f1_64k

@@ -3,7 +3,7 @@
 source ./buildroot/bin/buildFunctions;
 exitcode=0;
 
-# CC2500-only 64Kb builds
+# CC2500-only 64Kb FCC builds
 printf "\e[33;1mBuilding mm-stm-cc2500-64-aetr-v$MULTI_VERSION.bin\e[0m\n";
 opt_enable $ALL_PROTOCOLS;
 opt_disable IKEAANSLUTA_CC2500_INO;
@@ -28,4 +28,24 @@ buildMulti;
 exitcode=$((exitcode+$?));
 mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-64-reta-v$MULTI_VERSION.bin;
 
+# CC2500-only 64Kb LBT/EU builds
+printf "\e[33;1mBuilding mm-stm-cc2500-64-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace RETA AETR;
+opt_add MULTI_EU;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-64-aetr-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-cc2500-64-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-64-taer-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-cc2500-64-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-64-reta-lbt-v$MULTI_VERSION.bin;
+
 exit $exitcode;

buildroot/bin/build_release_stm32f1_no_debug

@@ -3,11 +3,7 @@
 source ./buildroot/bin/buildFunctions;
 exitcode=0;
 
-# Builds for the DIY 5-in-1 module exceed the 120KB working capacity of the STM32F103CB
-# To work around this we have to disable some protocols in the builds for this module
-#DIY_5IN1_DISABLED="MOULDKG_NRF24L01_INO";
-
-# Generic 4-in-1 builds
+# Generic 4-in-1 FCC builds
 printf "\e[33;1mBuilding mm-stm-serial-aetr-v$MULTI_VERSION.bin\e[0m\n";
 opt_disable ENABLE_PPM;
 buildMulti;
@@ -26,10 +22,30 @@ buildMulti;
 exitcode=$((exitcode+$?));
 mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-reta-v$MULTI_VERSION.bin;
 
+# Generic 4-in-1 LBT/EU builds
+printf "\e[33;1mBuilding mm-stm-serial-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace RETA AETR;
+opt_add MULTI_EU;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-aetr-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-serial-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-taer-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-serial-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-reta-lbt-v$MULTI_VERSION.bin;
+
 # DIY 5-in-1 builds
 printf "\e[33;1mBuilding mm-stm-5in1-aetr-v$MULTI_VERSION.bin\e[0m\n";
+opt_remove MULTI_EU;
 opt_replace RETA AETR;
-#opt_disable $DIY_5IN1_DISABLED;
 opt_enable SX1276_INSTALLED;
 buildMulti;
 exitcode=$((exitcode+$?));
@@ -52,7 +68,6 @@ printf "\e[33;1mBuilding mm-tlite5in1-aetr-v$MULTI_VERSION.bin\e[0m\n";
 opt_replace RETA AETR;
 opt_disable INVERT_TELEMETRY;
 opt_disable SX1276_INSTALLED;
-#opt_enable $DIY_5IN1_DISABLED;
 opt_enable "MULTI_5IN1_INTERNAL JP_TLite"
 buildMulti;
 exitcode=$((exitcode+$?));
@@ -70,7 +85,7 @@ buildMulti;
 exitcode=$((exitcode+$?));
 mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-reta-v$MULTI_VERSION.bin;
 
-# CC2500-only builds
+# CC2500-only FCC builds
 printf "\e[33;1mBuilding mm-stm-cc2500-aetr-v$MULTI_VERSION.bin\e[0m\n";
 opt_replace RETA AETR;
 opt_disable "MULTI_5IN1_INTERNAL JP_TLite"
@@ -94,11 +109,32 @@ buildMulti;
 exitcode=$((exitcode+$?));
 mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-reta-v$MULTI_VERSION.bin;
 
+# CC2500-only LBT/EU builds
+printf "\e[33;1mBuilding mm-stm-cc2500-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace RETA AETR;
+opt_add MULTI_EU;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-aetr-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-cc2500-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-taer-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-cc2500-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-reta-lbt-v$MULTI_VERSION.bin;
+
 # 4-in-1 PPM builds
 printf "\e[33;1mBuilding mm-stm-ppm-aetr-v$MULTI_VERSION.bin\e[0m\n";
 opt_enable A7105_INSTALLED;
 opt_enable CYRF6936_INSTALLED;
 opt_enable NRF24L01_INSTALLED;
+opt_remove MULTI_EU;
 opt_enable ENABLE_PPM;
 opt_disable ENABLE_SERIAL;
 opt_replace RETA AETR;

buildroot/bin/opt_remove

@@ -0,0 +1,5 @@
+#!/usr/bin/env bash
+
+SED=$(which gsed || which sed)
+
+eval "${SED} -i '/#define \b${1}/d' Multiprotocol/_Config.h"