Update Multiprotocol.h

* 4-in-1 air and surface builds

* Disable serial and PPM-only builds for STM32 x-in-1

* More air and surface builds

* Fix 5-in-1 tests

* T18 air, surface, and LBT builds

* Remove CFlie from DIY 5-in-1 AIR

* Bump action versions

* v4 artifact merging

* Improve artifact merge

* Fix merge

* DIY 5-in-1 LBT

* Tweak CI job name

* Add T-Lite 5-in-1 LBT

* CI job restructure

.github/workflows/main.yml

@@ -1,6 +1,6 @@
 # Workflow for testing MULTI-Module firmware builds
 
-name: CI
+name: MULTI Test, Build, Deploy, Release
 
 on:
   # Trigger the workflow on pushes, except those that are tagged (avoids double-testing releases)
@@ -32,7 +32,7 @@ on:
   workflow_dispatch:
 
 jobs:
-  build:
+  test:
     runs-on: ubuntu-latest
 
     # Configure the board matrix
@@ -51,21 +51,21 @@ jobs:
           - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=none"
             name: "STM32F103 (128KB)"
           - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=native"
-            name: "STM32F103 (128KB, USB Debugging)"
+            name: "STM32F103 (128KB, USB Debug)"
           - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=ftdi"
-            name: "STM32F103 (128KB, Serial Debugging)"
+            name: "STM32F103 (128KB, Serial Debug)"
           - board: "multi4in1:STM32F1:multi5in1t18int"
             name: "T18 5-in-1 (128KB)"
 
     # Set the build name using the friendly board name
-    name: ${{ matrix.name }}
+    name: "[Test] ${{ matrix.name }}"
 
     # Set the environment variables
     env:
       BOARD: ${{ matrix.board }}
 
     steps:
-      - uses: actions/checkout@v3
+      - uses: actions/checkout@v4
       
       - name: Install Arduino CLI
         uses: arduino/setup-arduino-cli@v1.1.2
@@ -161,23 +161,38 @@ jobs:
 
       - name: Build serial only
         run: |
-          source ./buildroot/bin/buildFunctions;
-          cp ./_Config.h.bak Multiprotocol/_Config.h
-          opt_disable ENABLE_PPM;
-          buildMulti;
+          # Skip the serial-only build for boards where it's too large now
+          if [[ "$BOARD" =~ ":STM32F1:multistm32f103cb:debug_option=none" ]] || [[ "$BOARD" =~ ":STM32F1:multi5in1t18int" ]]; then
+            printf "Not testing serial-only build for $BOARD.";
+          else
+            source ./buildroot/bin/buildFunctions;
+            cp ./_Config.h.bak Multiprotocol/_Config.h
+            opt_disable ENABLE_PPM;
+            buildMulti;
+          fi
       
       - name: Build PPM only
         run: |
-          source ./buildroot/bin/buildFunctions;
-          cp ./_Config.h.bak Multiprotocol/_Config.h
-          opt_disable ENABLE_SERIAL;
-          buildMulti;
+          # Skip the PPM-only build for boards where it's too large now
+          if [[ "$BOARD" =~ ":STM32F1:multistm32f103cb:debug_option=none" ]] || [[ "$BOARD" =~ ":STM32F1:multi5in1t18int" ]]; then
+            printf "Not testing PPM-only build for $BOARD.";
+          else
+            source ./buildroot/bin/buildFunctions;
+            cp ./_Config.h.bak Multiprotocol/_Config.h
+            opt_disable ENABLE_SERIAL;
+            buildMulti;
+          fi
 
       - name: Build each RF module individually
         run: |
-          source ./buildroot/bin/buildFunctions;
-          cp ./_Config.h.bak Multiprotocol/_Config.h;
-          buildEachRFModule;
+          # Skip the per-RF module builds for boards which have fixed modules
+          if [[ "$BOARD" =~ ":STM32F1:multi5in1t18int" ]]; then
+            printf "Not testing individual RF module builds for $BOARD.";
+          else
+            source ./buildroot/bin/buildFunctions;
+            cp ./_Config.h.bak Multiprotocol/_Config.h;
+            buildEachRFModule;
+          fi
 
       - name: Build each protocol individually
         run: |
@@ -185,6 +200,128 @@ jobs:
           cp ./_Config.h.bak Multiprotocol/_Config.h;
           buildEachProtocol;
 
+  build:
+    runs-on: ubuntu-latest
+
+    # Configure the board matrix
+    strategy:
+      fail-fast: false
+      matrix:
+        include:
+          - board: "multi4in1:avr:multiatmega328p:bootloader=none"
+            name: "ATmega328p"
+            release: "atmega328p"
+          - board: "multi4in1:avr:multiatmega328p:bootloader=optiboot"
+            name: "ATmega328p (Optiboot)"
+            release: "atmega328p-optiboot"
+          - board: "multi4in1:avr:multixmega32d4"
+            name: "OrangeRX"
+            release: "orangerx"
+          - board: "multi4in1:STM32F1:multistm32f103c8:debug_option=none"
+            name: "STM32F103 CC2500 (64KB)"
+            release: "stm32f103-cc2500-64k"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=none"
+            name: "STM32F103 CC2500 (128KB)"
+            release: "stm32f103-cc2500-128k"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=none"
+            name: "STM32F103 (128KB)"
+            release: "stm32f103-128k-4in1"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=native"
+            name: "STM32F103 (128KB, USB Debug)"
+            release: "stm32f103-128k-usb-debug"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=ftdi"
+            name: "STM32F103 (128KB, Serial Debug)"
+            release: "stm32f103-128k-serial-debug"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=none"
+            name: "STM32F103 5-in-1 (128KB)"
+            release: "stm32f103-128k-5in1"
+          - board: "multi4in1:STM32F1:multistm32f103cb:debug_option=none"
+            name: "T-Lite 5-in-1 (128KB)"
+            release: "tlite-5in1"
+          - board: "multi4in1:STM32F1:multi5in1t18int"
+            name: "T18 5-in-1 (128KB)"
+            release: "t18-5in1"
+          - board: "none"
+            name: "Scripts"
+            release: "scripts"
+
+    # Set the build name using the friendly board name
+    name: "[Build] ${{ matrix.name }}"
+
+    # Set the environment variables
+    env:
+      BOARD: ${{ matrix.board }}
+      RELEASE: ${{ matrix.release }}
+
+    steps:
+      - uses: actions/checkout@v4
+      
+      - name: Install Arduino CLI
+        uses: arduino/setup-arduino-cli@v1.1.2
+        with:
+          version: "0.32.2"
+      
+      - name: Prepare build environment
+        run: |
+          echo "Github Ref: $GITHUB_REF"
+          echo "Event name: ${{ github.event_name }}"
+          echo "Event action: ${{ github.event.action }}"
+          echo "Tag name: ${{ github.event.release.tag_name }}"
+
+          arduino-cli config init --additional-urls https://raw.githubusercontent.com/pascallanger/DIY-Multiprotocol-TX-Module-Boards/master/package_multi_4in1_board_index.json,https://raw.githubusercontent.com/pascallanger/DIY-Multiprotocol-TX-Module-Boards/devel/source/package_multi_4in1_board_devel_index.json
+          arduino-cli core update-index
+          
+          if [[ "$BOARD" =~ ":avr:" ]]; then
+            arduino-cli core install arduino:avr;
+          fi
+
+          if [[ "$BOARD" =~ "multi4in1-devel:avr" ]]; then
+            arduino-cli core install multi4in1-devel:avr
+          elif [[ "$BOARD" =~ "multi4in1:avr" ]]; then
+            arduino-cli core install multi4in1:avr
+          fi
+
+          if [[ "$BOARD" =~ "multi4in1-devel:STM32F1:" ]]; then
+            arduino-cli core install multi4in1-devel:STM32F1
+          elif [[ "$BOARD" =~ "multi4in1:STM32F1:" ]]; then
+            arduino-cli core install multi4in1:STM32F1
+          fi
+
+          chmod +x ${GITHUB_WORKSPACE}/buildroot/bin/*
+          echo "${GITHUB_WORKSPACE}/buildroot/bin" >> $GITHUB_PATH
+
+          mkdir ./build
+          mkdir ./binaries
+
+      - name: Configure MULTI-Module firmware options
+        run: |
+          # Load the build functions
+          source ./buildroot/bin/buildFunctions;  
+          
+          # Get the version
+          getMultiVersion
+          echo "MULTI_VERSION=$(echo $MULTI_VERSION)" >> $GITHUB_ENV
+
+          # Get all the protocols for this board
+          getAllProtocols
+          echo "A7105_PROTOCOLS=$(echo $A7105_PROTOCOLS)" >> $GITHUB_ENV
+          echo "CC2500_PROTOCOLS=$(echo $CC2500_PROTOCOLS)" >> $GITHUB_ENV
+          echo "CYRF6936_PROTOCOLS=$(echo $CYRF6936_PROTOCOLS)" >> $GITHUB_ENV
+          echo "NRF24L01_PROTOCOLS=$(echo $NRF24L01_PROTOCOLS)" >> $GITHUB_ENV
+          echo "SX1276_PROTOCOLS=$(echo $SX1276_PROTOCOLS)" >> $GITHUB_ENV
+          echo "CCNRF_INO_PROTOCOLS=$(echo $CCNRF_INO_PROTOCOLS)" >> $GITHUB_ENV
+          echo "ALL_PROTOCOLS=$(echo $ALL_PROTOCOLS)" >> $GITHUB_ENV
+
+          # Disable CHECK_FOR_BOOTLOADER when not needed
+          if [[ "$BOARD" =~ ":avr:multiatmega328p:bootloader=none" ]]; then
+            opt_disable CHECK_FOR_BOOTLOADER;
+          fi
+
+      - name: Save default firmware configuration
+        run: |
+          cat Multiprotocol/_Config.h
+          cp Multiprotocol/_Config.h ./_Config.h.bak
+
       - name: Build release files
         run: |
           source ./buildroot/bin/buildFunctions;
@@ -199,16 +336,43 @@ jobs:
             echo "HAVE_FILES=false" >> $GITHUB_ENV
           fi
 
-      - name: Deploy files to release
-        if: github.event_name == 'release' && github.event.action == 'created' && env.HAVE_FILES == 'true'
-        uses: AButler/upload-release-assets@v2.0
-        with:
-          files: './binaries/*'
-          repo-token: ${{ secrets.GITHUB_TOKEN }}
-
       - name: 'Upload Artifacts'
         if: env.HAVE_FILES == 'true'
-        uses: actions/upload-artifact@v3
+        uses: actions/upload-artifact/@v4
+        with:
+          name: multi-${{ matrix.release }}
+          path: ./binaries/
+
+  deploy:
+    name: "[Deploy] Attach Build Artifacts"
+    runs-on: ubuntu-latest
+    needs: [test, build]
+    steps:
+      - name: Combine and upload build artifacts
+        uses: actions/upload-artifact/merge@v4
         with:
           name: multi-test-build
-          path: ./binaries/
+          pattern: multi-*
+          delete-merged: true
+          retention-days: 90
+
+  release:
+    name: "[Release] Publish Files to Release"
+    if: github.event_name == 'release' && github.event.action == 'created'
+    runs-on: ubuntu-latest
+    needs: deploy
+    steps:
+      - name: Download artifacts
+        uses: actions/download-artifact@v4
+        with:
+          name: multi-test-build
+          path: ./artifacts/
+      
+      - name: Display downloaded artifacts
+        run: ls -R ./artifacts/
+      
+      - name: Deploy artifacts to release
+        uses: AButler/upload-release-assets@v3.0
+        with:
+          files: './artifacts/*'
+          repo-token: ${{ secrets.GITHUB_TOKEN }}

Lua_scripts/MultiChan.txt

@@ -157,7 +157,7 @@
 74,1,RadioLink,Air,0,CH5,CH6,CH7,CH8,FS_CH1,FS_CH2,FS_CH3,FS_CH4,FS_CH5,FS_CH6,FS_CH7,FS_CH8
 74,2,RadioLink,DumboRC,0,CH5,CH6,CH7,CH8,FS_CH1,FS_CH2,FS_CH3,FS_CH4,FS_CH5,FS_CH6,FS_CH7,FS_CH8
 74,3,RadioLink,RC4G,0,CH5,FS_CH1,FS_CH2,FS_CH3,FS_CH4
-76,0,Realacc,R11,1,Flip,Light,Calib,HLess,RTH,UNK
+76,0,Realacc,Std,1,Flip,Light,Calib,HLess,RTH,UNK
 50,0,Redpine,Fast,0,sCH5,sCH6,sCH7,sCH8,sCH9,sCH10,sCH11,sCH12,sCH13,sCH14,sCH15,sCH16
 50,1,Redpine,Slow,0,sCH5,sCH6,sCH7,sCH8,sCH9,sCH10,sCH11,sCH12,sCH13,sCH14,sCH15,sCH16
 21,0,Futaba,SFHSS,0,CH5,CH6,CH7,CH8
@@ -170,7 +170,7 @@
 11,4,SLT,MR100,0,Rates,n-a,CH7,CH8,Mode,Flip,Video,Pict
 10,0,Symax,Std,1,Flip,Rates,Pict,Video,HLess
 10,1,Symax,X5C,1,Flip,Rates,Pict,Video,HLess
-43,0,Traxxas,6519,0
+43,0,Traxxas,TQ,0
 5,0,V2x2,Std,1,Flip,Light,Pict,Video,HLess,CalX,CalY
 5,1,V2x2,JXD506,1,Flip,Light,Pict,Video,HLess,StaSto,Emerg,Cam_UD
 48,0,V761,3CH,0,Gyro,Calib,Flip,RtnAct,Rtn
@@ -214,3 +214,4 @@
 95,0,Bluefly,HP100,0,CH5,CH6,CH7,CH8
 96,0,BumbleB
 97,0,SGF22,Std,1,Mode,Flip,LED,Pict,Video
+61,1,EazyRC

Multiprotocol/DSM_cyrf6936.ino

@@ -174,19 +174,21 @@ static void __attribute__((unused)) DSM_build_data_packet(uint8_t upper)
 			bits=10;								// Only DSM2_1F is using a resolution of 1024
 	}
 
-	if(sub_protocol == DSMR)
-	{
-		for (uint8_t i = 0; i < 7; i++)
+	#ifndef MULTI_AIR
+		if(sub_protocol == DSMR)
 		{
-			uint16_t value = 0x0000;
-			if(i < num_ch)
-				value=Channel_data[i]<<1;
-			packet[i*2+2] = (value >> 8) & 0xff;
-			packet[i*2+3] = (value >> 0) & 0xff;
+			for (uint8_t i = 0; i < 7; i++)
+			{
+				uint16_t value = 0x0000;
+				if(i < num_ch)
+					value=Channel_data[i]<<1;
+				packet[i*2+2] = (value >> 8) & 0xff;
+				packet[i*2+3] = (value >> 0) & 0xff;
+			}
+			return;
 		}
-		return;
-	}
-
+	#endif
+	
 	#ifdef DSM_THROTTLE_KILL_CH
 		uint16_t kill_ch=Channel_data[DSM_THROTTLE_KILL_CH-1];
 	#endif
@@ -267,6 +269,10 @@ uint16_t DSM_callback()
 		if(sub_protocol == DSM2_1F || sub_protocol == DSM2_2F)
 			return 11000;
 	#endif
+	#if defined MULTI_AIR
+		if(sub_protocol == DSMR)
+			return 11000;
+	#endif
 	#define DSM_CH1_CH2_DELAY	4010			// Time between write of channel 1 and channel 2
 	#ifdef STM32_BOARD
 		#define DSM_WRITE_DELAY		1600		// Time after write to verify write complete
@@ -506,6 +512,7 @@ uint16_t DSM_callback()
 }
 
 
+#ifndef MULTI_AIR
 const uint8_t PROGMEM DSMR_ID_FREQ[][4 + 23] = {
 	{ 0x71, 0x74, 0x1c, 0xe4, 0x11, 0x2f, 0x17, 0x3d, 0x23, 0x3b, 0x0f, 0x21, 0x25, 0x49, 0x1d, 0x13, 0x4d, 0x1f, 0x41, 0x4b, 0x47, 0x05, 0x27, 0x15, 0x19, 0x3f, 0x07 },
 	{ 0xfe, 0xfe, 0xfe, 0xfe, 0x45, 0x31, 0x33, 0x4b, 0x11, 0x29, 0x49, 0x3f, 0x09, 0x13, 0x47, 0x21, 0x1d, 0x43, 0x1f, 0x05, 0x41, 0x19, 0x1b, 0x2d, 0x15, 0x4d, 0x0f },
@@ -529,22 +536,27 @@ const uint8_t PROGMEM DSMR_ID_FREQ[][4 + 23] = {
 	{ 0xff, 0xff, 0x00, 0x00, 0x2b, 0x35, 0x1b, 0x1d, 0x0f, 0x47, 0x09, 0x0d, 0x45, 0x41, 0x21, 0x11, 0x2f, 0x43, 0x27, 0x33, 0x4b, 0x37, 0x13, 0x19, 0x4d, 0x23, 0x17 },
 	{ 0x00, 0xff, 0x00, 0x00, 0x1b, 0x1d, 0x33, 0x13, 0x2b, 0x27, 0x09, 0x41, 0x25, 0x17, 0x19, 0x2d, 0x4b, 0x37, 0x45, 0x11, 0x21, 0x0d, 0x3d, 0x4d, 0x07, 0x39, 0x43 },
 	{ 0xff, 0x00, 0x00, 0x00, 0x37, 0x27, 0x43, 0x4b, 0x39, 0x13, 0x07, 0x0d, 0x25, 0x17, 0x29, 0x1b, 0x1d, 0x45, 0x19, 0x2d, 0x0b, 0x3d, 0x15, 0x47, 0x1f, 0x21, 0x4d } };
+#endif
 
 void DSM_init()
 { 
 	if(sub_protocol == DSMR)
 	{
-		if(option&CLONE_BIT_MASK)
+		#ifndef MULTI_AIR
+			if(option&CLONE_BIT_MASK)
+				SUB_PROTO_INVALID;
+			else
+			{
+				SUB_PROTO_VALID;
+				uint8_t row = rx_tx_addr[3]%22;
+				for(uint8_t i=0; i< 4; i++)
+					cyrfmfg_id[i] = pgm_read_byte_near(&DSMR_ID_FREQ[row][i]);
+				for(uint8_t i=0; i< 23; i++)
+					hopping_frequency[i] = pgm_read_byte_near(&DSMR_ID_FREQ[row][i+4]);
+			}
+		#else
 			SUB_PROTO_INVALID;
-		else
-		{
-			SUB_PROTO_VALID;
-			uint8_t row = rx_tx_addr[3]%22;
-			for(uint8_t i=0; i< 4; i++)
-				cyrfmfg_id[i] = pgm_read_byte_near(&DSMR_ID_FREQ[row][i]);
-			for(uint8_t i=0; i< 23; i++)
-				hopping_frequency[i] = pgm_read_byte_near(&DSMR_ID_FREQ[row][i+4]);
-		}
+		#endif
 	}
 	else
 	{

Multiprotocol/EazyRC_nrf24l01.ino

@@ -0,0 +1,166 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#if defined(EAZYRC_NRF24L01_INO)
+
+#include "iface_xn297.h"
+
+//#define FORCE_EAZYRC_ORIGINAL_ID
+
+#define EAZYRC_PAYLOAD_SIZE			10
+#define EAZYRC_RF_NUM_CHANNELS		4
+#define EAZYRC_BIND_CHANNEL			18
+#define EAZYRC_PACKET_PERIOD		5000
+
+enum {
+	EAZYRC_BINDTX=0,
+	EAZYRC_BINDRX,
+	EAZYRC_DATA,
+};
+
+static void __attribute__((unused)) EAZYRC_send_packet()
+{
+	//Bind:
+	// TX:    C=18 S=Y A= AA BB CC DD EE P(10)= 1A A0 01 00 00 00 1E 00 78 51
+	//   packet[0..2]=tx_addr, packet[6]=first rf channel, packet[8]=unk, packet[9]=sum(packet[0..8])
+	// RX:    C=18 S=Y A= AA BB CC DD EE P(10)= 41 AD 01 1A A0 01 1E 00 87 4F
+	//   packet[0..2]=rx_addr, packet[3..5]=tx_addr, packet[6]=first rf channel, packet[8]=unk but swapped, packet[9]=sum(packet[0..8])
+	//Normal: C=30 S=Y A= 1A A0 41 AD 02 P(10)= 7F 7F 1F 19 00 00 1E 00 AB FF
+	//   packet[0]=THR, packet[1]=ST, packet[2]=unk, packet[3]=unk, packet[6]=first rf channel, packet[8]=unk, packet[9]=sum(packet[0..8])
+	//Bound : C=18 S=Y A= AA BB CC DD EE P(10)= 1A A0 01 41 AD 01 1E 00 79 41
+	//   packet[0..2]=tx_addr, packet[3..5]=rx_addr, packet[6]=first rf channel, packet[8]=unk, packet[9]=sum(packet[0..8])
+	//   sent every 12 packets in normal mode, but is it really needed if the car loose power then you need to rebind...
+	//Packet period around 5ms with a large jitter
+
+	memset(&packet[3], 0x00, 7);
+	if(IS_BIND_IN_PROGRESS)
+	{
+		memcpy(&packet,rx_tx_addr,3);
+		packet[6] = hopping_frequency[0];
+		packet[8] = 0x78;						//??? packet type?
+	}
+	else
+	{
+		XN297_Hopping(hopping_frequency_no);
+		hopping_frequency_no++;
+		hopping_frequency_no &= 3;
+		
+		packet[0] = convert_channel_8b(THROTTLE);
+		packet[1] = convert_channel_8b(AILERON);
+		packet[2] = 0x1F;						//??? additional channel?
+		packet[3] = 0x19;						//??? additional channel?
+		packet[6] = hopping_frequency[0];
+		packet[8] = 0xAB;						//??? packet type?
+	}
+	for(uint8_t i=0;i<EAZYRC_PAYLOAD_SIZE-1;i++)
+		packet[9] += packet[i];
+	// Send
+	XN297_SetPower();
+	XN297_SetTxRxMode(TX_EN);
+	XN297_WritePayload(packet, EAZYRC_PAYLOAD_SIZE);
+	#ifdef DEBUG_SERIAL
+		for(uint8_t i=0; i < len; i++)
+			debug("%02X ", packet[i]);
+		debugln();
+	#endif
+}
+
+static void __attribute__((unused)) EAZYRC_initialize_txid()
+{
+	rx_tx_addr[1] = rx_tx_addr[3];
+	hopping_frequency[0] = (rx_tx_addr[3]%20) + 0x1E;		// Wild guess... First channel between 30 and 49so a full range of 30 to 79
+	#ifdef FORCE_EAZYRC_ORIGINAL_ID
+		rx_tx_addr[0] = 0x1A;
+		rx_tx_addr[1] = 0xA0;
+		rx_tx_addr[2] = 0x01;
+		hopping_frequency[0] = 0x1E;
+	#endif
+	rx_tx_addr[2] = 0x01;									// Not sure if this is needed...
+	for(uint8_t i=1; i<EAZYRC_RF_NUM_CHANNELS; i++)
+		hopping_frequency[i] = hopping_frequency[0] + 10*i;
+}
+
+static void __attribute__((unused)) EAZYRC_RF_init()
+{
+	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_1M);
+	XN297_SetTXAddr((uint8_t*)"\xAA\xBB\xCC\xDD\xEE", 5);
+	XN297_SetRXAddr((uint8_t*)"\xAA\xBB\xCC\xDD\xEE", EAZYRC_PAYLOAD_SIZE);
+	XN297_RFChannel(EAZYRC_BIND_CHANNEL);
+}
+
+uint16_t EAZYRC_callback()
+{
+	uint8_t rf,n;
+	uint16_t addr;
+	switch(phase)
+	{
+		case EAZYRC_BINDTX:
+			if(XN297_IsRX())
+			{
+				//Example:	TX: C=18 S=Y A= AA BB CC DD EE P(10)= 1A A0 01 00 00 00 1E 00 78 51
+				// packet[0..2]=tx_addr, packet[6]=first rf channel, packet[8]=unk, packet[9]=sum(packet[0..8])
+				//			RX: C=18 S=Y A= AA BB CC DD EE P(10)= 41 AD 01 1A A0 01 1E 00 87 4F
+				// packet[0..2]=rx_addr, packet[3..5]=tx_addr, packet[6]=first rf channel, packet[8]=unk but swapped, packet[9]=sum(packet[0..8])
+				XN297_ReadPayload(packet_in, EAZYRC_PAYLOAD_SIZE);
+				#ifdef DEBUG_SERIAL
+					for(uint8_t i=0; i < EAZYRC_PAYLOAD_SIZE; i++)
+						debug("%02X ", packet_in[i]);
+					debugln();
+				#endif
+				//could check the validity of the packet by looking at the sum...
+				if(memcmp(&packet_in[3],&rx_tx_addr,3)==0)
+				{//TX ID match, TX addr to use: 1A A0 41 AD 02
+					rx_tx_addr[4] = rx_tx_addr[2] + packet_in[2];	//wild guess
+					rx_tx_addr[2] = packet_in[0];
+					rx_tx_addr[3] = packet_in[1];
+					BIND_DONE;
+					XN297_SetTxRxMode(TXRX_OFF);
+					XN297_SetTXAddr(rx_tx_addr, 5);
+					phase = EAZYRC_DATA;
+					return 5000;
+				}
+			}
+			XN297_SetTxRxMode(TXRX_OFF);
+			EAZYRC_send_packet();
+			phase++;
+			return 1000;
+		case EAZYRC_BINDRX:
+			//Wait for the packet transmission to finish
+			while(XN297_IsPacketSent()==false);
+			//Switch to RX
+			XN297_SetTxRxMode(TXRX_OFF);
+			XN297_SetTxRxMode(RX_EN);
+			phase = EAZYRC_BINDTX;
+			return 10000;
+		case EAZYRC_DATA:
+			#ifdef MULTI_SYNC
+				telemetry_set_input_sync(EAZYRC_PACKET_PERIOD);
+			#endif
+			EAZYRC_send_packet();
+			break;
+	}
+	return EAZYRC_PACKET_PERIOD;
+}
+
+void EAZYRC_init()
+{
+	BIND_IN_PROGRESS;
+	EAZYRC_initialize_txid();
+	EAZYRC_RF_init();
+	phase = EAZYRC_BINDTX;
+	packet_count = 0;
+	hopping_frequency_no = 0;
+}
+
+#endif

Multiprotocol/Multi.txt

@@ -40,7 +40,7 @@
 40,WFLY,WFR0x
 41,BUGS
 42,BUGSMINI,BUGSMINI,BUGS3H
-43,Traxxas,RX6519
+43,Traxxas,TQ
 44,NCC1701
 45,E01X,E012,E015
 46,V911S,V911S,E119
@@ -58,6 +58,7 @@
 58,FX,816,620,9630
 59,Bayang_RX,Multi,CPPM
 60,Pelikan,Pro,Lite,SCX24
+61,EazyRC
 62,XK,X450,X420,Cars
 63,XN_DUMP,250K,1M,2M,AUTO
 64,FrskyX2,CH_16,CH_8,EU_16,EU_8,Cloned
@@ -72,7 +73,7 @@
 73,Kyosho,FHSS,Hype
 74,RadioLink,Surface,Air,DumboRC,RC4G
 75,---
-76,Realacc,R11
+76,Realacc
 77,OMP
 78,M-Link
 79,WFLY,RF20x

Multiprotocol/Multi_Protos.ino

@@ -108,6 +108,7 @@ const char STR_SCORPIO[]    ="Scorpio";
 const char STR_BLUEFLY[]    ="BlueFly";
 const char STR_BUMBLEB[]    ="BumbleB";
 const char STR_SGF22[]      ="SGF22";
+const char STR_EAZYRC[]     ="EazyRC";
 
 const char STR_SUBTYPE_FLYSKY[] =     "\x04""Std\0""V9x9""V6x6""V912""CX20";
 const char STR_SUBTYPE_HUBSAN[] =     "\x04""H107""H301""H501";
@@ -146,7 +147,7 @@ const char STR_SUBTYPE_H83D[] =       "\x07""Std\0   ""H20H\0  ""H20Mini""H30Min
 const char STR_SUBTYPE_CORONA[] =     "\x05""V1\0  ""V2\0  ""FD V3";
 const char STR_SUBTYPE_HITEC[] =      "\x07""Optima\0""Opt Hub""Minima\0";
 const char STR_SUBTYPE_BUGS_MINI[] =  "\x06""Std\0  ""Bugs3H";
-const char STR_SUBTYPE_TRAXXAS[] =    "\x04""6519";
+const char STR_SUBTYPE_TRAXXAS[] =    "\x02""TQ";
 const char STR_SUBTYPE_E01X[] =       "\x05""E012\0""E015\0";
 const char STR_SUBTYPE_GD00X[] =      "\x05""GD_V1""GD_V2";
 const char STR_SUBTYPE_REDPINE[] =    "\x04""Fast""Slow";
@@ -168,7 +169,6 @@ const char STR_SUBTYPE_HOTT[] =       "\x07""Sync\0  ""No_Sync";
 const char STR_SUBTYPE_PELIKAN[] =    "\x05""Pro\0 ""Lite\0""SCX24";
 const char STR_SUBTYPE_V761[] =       "\x05""3ch\0 ""4ch\0 ""TOPRC";
 const char STR_SUBTYPE_RLINK[] =      "\x07""Surface""Air\0   ""DumboRC""RC4G\0  ";
-const char STR_SUBTYPE_REALACC[] =    "\x03""R11";
 const char STR_SUBTYPE_KYOSHO[] =     "\x04""FHSS""Hype";
 const char STR_SUBTYPE_KYOSHO2[] =    "\x05""KT-17";
 const char STR_SUBTYPE_FUTABA[] =     "\x05""SFHSS";
@@ -278,6 +278,9 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(E129_CYRF6936_INO)
 		{PROTO_E129,       STR_E129,      STR_SUBTYPE_E129,      2, OPTION_NONE,    0, 0, SW_CYRF,   E129_init,       E129_callback       },
 	#endif
+	#if defined(EAZYRC_NRF24L01_INO)
+		{PROTO_EAZYRC,     STR_EAZYRC,    NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    EAZYRC_init,     EAZYRC_callback     },
+	#endif
 	#if defined(ESKY_NRF24L01_INO)
 		{PROTO_ESKY,       STR_ESKY,      STR_SUBTYPE_ESKY,      2, OPTION_NONE,    0, 1, SW_NRF,    ESKY_init,       ESKY_callback       },
 	#endif
@@ -433,7 +436,7 @@ const mm_protocol_definition multi_protocols[] = {
 		{PROTO_RLINK,      STR_RLINK,     STR_SUBTYPE_RLINK,     4, OPTION_RFTUNE,  0, 0, SW_CC2500, RLINK_init,      RLINK_callback      },
 	#endif
 	#if defined(REALACC_NRF24L01_INO)
-		{PROTO_REALACC,    STR_REALACC,   STR_SUBTYPE_REALACC,   1, OPTION_NONE,    0, 0, SW_NRF,    REALACC_init,    REALACC_callback    },
+		{PROTO_REALACC,    STR_REALACC,   NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    REALACC_init,    REALACC_callback    },
 	#endif
 	#if defined(REDPINE_CC2500_INO)
 		{PROTO_REDPINE,    STR_REDPINE,   STR_SUBTYPE_REDPINE,   2, OPTION_RFTUNE,  0, 0, SW_CC2500, REDPINE_init,    REDPINE_callback    },

Multiprotocol/Multiprotocol.h

@@ -18,8 +18,8 @@
 //******************
 #define VERSION_MAJOR		1
 #define VERSION_MINOR		3
-#define VERSION_REVISION	3
-#define VERSION_PATCH_LEVEL	49
+#define VERSION_REVISION	4
+#define VERSION_PATCH_LEVEL	0
 
 #define MODE_SERIAL 0
 
@@ -89,7 +89,7 @@ enum PROTOCOLS
 	PROTO_FX		= 58,	// =>NRF24L01
 	PROTO_BAYANG_RX	= 59,	// =>NRF24L01
 	PROTO_PELIKAN	= 60,	// =>A7105
-
+	PROTO_EAZYRC	= 61,	// =>NRF24L01
 	PROTO_XK		= 62,	// =>NRF24L01
 	PROTO_XN297DUMP	= 63,	// =>NRF24L01
 	PROTO_FRSKYX2	= 64,	// =>CC2500
@@ -360,7 +360,7 @@ enum REDPINE
 };
 enum TRAXXAS
 {
-	RX6519	= 0,
+	TRAXXAS_TQ	= 0,
 };
 enum ESKY150
 {
@@ -1106,7 +1106,7 @@ Serial: 100000 Baud 8e2      _ xxxx xxxx p --
 			RED_FAST	0
 			RED_SLOW	1
 		sub_protocol==TRAXXAS
-			RX6519		0
+			TQ			0
 		sub_protocol==ESKY150
 			ESKY150_4CH	0
 			ESKY150_7CH	1

Multiprotocol/RadioLink_cc2500.ino

@@ -22,7 +22,7 @@
 //#define RLINK_DEBUG_TELEM
 
 //#define RLINK_FORCE_ID
-#define RLINK_RC4G_FORCE_ID
+//#define RLINK_RC4G_FORCE_ID
 
 #define RLINK_TX_PACKET_LEN	33
 #define RLINK_RX_PACKET_LEN	15
@@ -120,11 +120,44 @@ static void __attribute__((unused)) RLINK_TXID_init()
 	if(sub_protocol!=RLINK_RC4G)
 		RLINK_hop();
 	else
-	{
+	{//RLINK_RC4G
 		// Find 2 unused channels
 		//  first  channel is a multiple of 3 between 00 and 5D
 		//  second channel is a multiple of 3 between 63 and BD
-		//TODO: find 2 unused channels
+		CC2500_Strobe(CC2500_SIDLE);
+		CC2500_WriteReg(CC2500_17_MCSM1,0x3C);
+		CC2500_Strobe(CC2500_SFRX);
+		CC2500_SetTxRxMode(RX_EN);
+		CC2500_Strobe(CC2500_SRX);
+		delayMilliseconds(1);						//wait for RX mode
+		uint16_t val;
+		uint8_t val_low = 0xFF;
+		hopping_frequency[0] = 0x00;
+		hopping_frequency[1] = 0x63;
+		for(uint8_t ch=0; ch<=0xBD; ch+=3)
+		{
+			if(ch==0x63)
+				val_low	= 0xFF;						//init for second block
+			if(ch==0x60)
+				continue;							//skip channel
+			CC2500_WriteReg(CC2500_0A_CHANNR, ch);	//switch channel
+			delayMicroseconds(370);					//wait to read
+			val = 0;
+			for(uint8_t i=0;i<16;i++)
+				val += CC2500_ReadReg(CC2500_34_RSSI | CC2500_READ_BURST);
+			val >>= 4;
+			debug("C:%02X RSSI:%02X",ch,val);
+			if(val_low > val)
+			{
+				debug(" OK");
+				val_low = val;
+				hopping_frequency[ch<0x63?0:1]=ch;	//save best channel
+			}
+			debugln("");
+		}
+		CC2500_WriteReg(CC2500_17_MCSM1,0x30);
+		CC2500_Strobe(CC2500_SIDLE);
+		CC2500_SetTxRxMode(TX_EN);
 		#ifdef RLINK_RC4G_FORCE_ID
 			hopping_frequency[0] = 0x03;
 			hopping_frequency[1] = 0x6F;
@@ -255,6 +288,7 @@ static void __attribute__((unused)) RLINK_send_packet()
 	#endif
 }
 
+#ifndef MULTI_AIR
 static void __attribute__((unused)) RLINK_RC4G_send_packet()
 {
 	uint32_t val;
@@ -292,10 +326,11 @@ static void __attribute__((unused)) RLINK_RC4G_send_packet()
 	#ifdef RLINK_DEBUG
 		debug("P=");
 		for(uint8_t i=1;i<16;i++)
-		debug(" 0x%02X",packet[i]);
+			debug(" 0x%02X",packet[i]);
 		debugln("");
 	#endif
 }
+#endif
 
 #define RLINK_TIMING_PROTO	20000-100		// -100 for compatibility with R8EF
 #define RLINK_TIMING_RFSEND	10500
@@ -305,10 +340,16 @@ uint16_t RLINK_callback()
 {
 	if(sub_protocol == RLINK_RC4G)
 	{
-		#ifdef MULTI_SYNC
-			telemetry_set_input_sync(RLINK_RC4G_TIMING_PROTO);
+		#ifndef MULTI_AIR
+			#ifdef MULTI_SYNC
+				telemetry_set_input_sync(RLINK_RC4G_TIMING_PROTO);
+			#endif
+			CC2500_SetPower();
+			CC2500_SetFreqOffset();
+			RLINK_RC4G_send_packet();
+		#else
+			SUB_PROTO_INVALID;
 		#endif
-		RLINK_RC4G_send_packet();
 		return RLINK_RC4G_TIMING_PROTO;
 	}
 	switch(phase)

Multiprotocol/Validate.h

@@ -312,6 +312,7 @@
 	#undef	CX10_NRF24L01_INO
 	#undef	DM002_NRF24L01_INO
 	#undef	E016H_NRF24L01_INO
+	#undef	EAZYRC_NRF24L01_INO
 	#undef	ESKY_NRF24L01_INO
 	#undef	ESKY150_NRF24L01_INO
 	#undef	FQ777_NRF24L01_INO
@@ -374,6 +375,7 @@
 	//#undef	PELIKAN_A7105_INO
 	#undef	LOSI_CYRF6936_INO		//Need DSM to be enabled
 	#undef	TRAXXAS_CYRF6936_INO
+	#undef	EAZYRC_NRF24L01_INO
 	#undef	KYOSHO2_NRF24L01_INO
 	#undef	MOULDKG_NRF24L01_INO
 	#undef	SHENQI_NRF24L01_INO

Multiprotocol/_Config.h

@@ -227,6 +227,7 @@
 #define	CX10_NRF24L01_INO		//Include Q2X2 protocol
 #define	DM002_NRF24L01_INO
 #define	E016H_NRF24L01_INO
+#define	EAZYRC_NRF24L01_INO
 #define	ESKY_NRF24L01_INO
 #define	ESKY150_NRF24L01_INO
 #define	FQ777_NRF24L01_INO
@@ -621,6 +622,8 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 	PROTO_E129
 		E129_E129
 		E129_C186
+	PROTO_EAZYRC
+		NONE
 	PROTO_ESKY
 		ESKY_STD
 		ESKY_ET4
@@ -816,7 +819,7 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 		SYMAX
 		SYMAX5C
 	PROTO_TRAXXAS
-		RX6519
+		NONE
 	PROTO_V2X2
 		V2X2
 		JXD506

Protocols_Details.md

@@ -82,6 +82,7 @@ CFlie|38|CFlie||||||||NRF24L01|
 [E016HV2](Protocols_Details.md#E016HV2---80)|80|||||||||CC2500/NRF24L01|unknown
 [E01X](Protocols_Details.md#E01X---45)|45|E012|E015|||||||CYRF6936|HS6200
 [E129](Protocols_Details.md#E129---83)|83|E129|C186|||||||CYRF6936|RF2500
+[EazyRC](Protocols_Details.md#EazyRC---61)|61|||||||||NRF24L01|XN297L
 [ESky](Protocols_Details.md#ESKY---16)|16|ESky|ET4|||||||NRF24L01|
 [ESky150](Protocols_Details.md#ESKY150---35)|35|||||||||NRF24L01|
 [ESky150V2](Protocols_Details.md#ESKY150V2---69)|69|||||||||CC2500|NRF51822
@@ -141,7 +142,7 @@ CFlie|38|CFlie||||||||NRF24L01|
 [Skyartec](Protocols_Details.md#Skyartec---68)|68|||||||||CC2500|CC2500
 [SLT](Protocols_Details.md#SLT---11)|11|SLT_V1|SLT_V2|Q100|Q200|MR100||||NRF24L01|CC2500
 [SymaX](Protocols_Details.md#Symax---10)|10|SYMAX|SYMAX5C|||||||NRF24L01|
-[Traxxas](Protocols_Details.md#Traxxas---43)|43|6519 RX||||||||CYRF6936|
+[Traxxas](Protocols_Details.md#Traxxas---43)|43|TQ||||||||CYRF6936|
 [V2x2](Protocols_Details.md#V2X2---5)|5|V2x2|JXD506|MR101||||||NRF24L01|
 [V761](Protocols_Details.md#V761---48)|48|3CH|4CH|TOPRC||||||NRF24L01|XN297
 [V911S](Protocols_Details.md#V911S---46)|46|V911S*|E119*|||||||NRF24L01|XN297
@@ -367,8 +368,6 @@ TX: Axial AX-4 2.4GHz transmitter, HPI TF-41 and Panda Hobby 3CH Smart Radio 2.4
 
 Models: Axial SCX24: Deadbolt, Jeep Wranger Rubicon, Chevrolet 1967 C10, B-17 Betty, HPI RF-50 and Panda Hobby: Tetra K1, X1, X2
 
-**Only 4 frequency hopping tables**
-
 Extended limits supported
 
 CH1|CH2|CH3
@@ -621,7 +620,7 @@ Calib is the same as the original radio with both sticks down and to the left in
 Models: Eachine E129/E130 and Twister Ninja 250
 
 ### Sub_protocol C186 - *1*
-Models: C186/E120, C127/E110, K127, C159, C189, C129v2
+Models: RC ERA C186/E120, C127/E110, K127, C159, C189, C129v2
 
 The FC of the heli seems to store the trims Trim A/E/R=CH7..9. If you use these trims, make sure to center them after powering off the heli or they will be added to the previous trims and over correct.
 
@@ -671,7 +670,7 @@ CH1|CH2|CH3|CH4
 A|E|T|R
 
 ## Traxxas - *43*
-Receiver 6519
+Transmitter TQ, Receivers: 6519, ECM-2.5
 
 Extended limits supported
 
@@ -1009,7 +1008,7 @@ CH1|CH2|CH3|CH4|CH5|FS_CH1|FS_CH2|FS_CH3|FS_CH4
 
 FS=FailSafe
 
-CH5 is driven by CH3 on the original TX, gyro sensibility?
+CH5 is driven by CH3 on the original TX, gyro sensitivity?
 
 ## Futaba - *21*
 Also called SFHSS depending on radio version.
@@ -1653,6 +1652,13 @@ CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9
 ---|---|---|---|---|---|---|---|---
 A|E|T|R|STOP|FLIP|-|HEADLESS|RTH
 
+## EazyRC - *61*
+Autobind protocol
+
+CH1|CH2|CH3|CH4
+---|---|---|---
+STEERING||THROTTLE|
+
 ## ESKY - *16*
 
 CH1|CH2|CH3|CH4|CH5|CH6
@@ -1943,14 +1949,10 @@ A|E|T|R|FLIP|LED|PICTURE|VIDEO|HEADLESS|RTH|XCAL|YCAL
 Model: JXD 509 is using Q282 with CH12=Start/Stop motors
 
 ## Realacc - *76*
-Model: Realacc R11
-
-Untested protocol, let me know if it works.
+Model: Realacc R11, Eachine E017
 
 Autobind protocol
 
-### Sub_protocol R11 - *0*
-
 CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10
 ---|---|---|---|---|---|---|---|---|----
 A|E|T|R|FLIP|LIGHT|CALIB|HLESS|RTH|UNK

buildroot/bin/buildFunctions

@@ -84,23 +84,30 @@ buildEachRFModule() {
 }
 
 buildReleaseFiles(){
-    if [[ "$BOARD" =~ ":avr:multixmega32d4" ]]; then
+    if [[ "$RELEASE" == "scripts" ]]; then
+        build_release_scripts;
+    elif [[ "$RELEASE" == "orangerx" ]]; then
         build_release_orx;
-        build_release_extras;
-    elif [[ "$BOARD" =~ ":avr:multiatmega328p:bootloader=none" ]]; then
+    elif [[ "$RELEASE" == "atmega328p" ]]; then
         build_release_avr_noboot;
-    elif [[ "$BOARD" =~ ":avr:multiatmega328p:bootloader=optiboot" ]]; then
+    elif [[ "$RELEASE" == "atmega328p-optiboot" ]]; then
         build_release_avr_optiboot;
-    elif [[ "$BOARD" =~ ":STM32F1:multistm32f103cb:debug_option=none" ]]; then
-        build_release_stm32f1_no_debug;
-    elif [[ "$BOARD" =~ ":STM32F1:multistm32f103cb:debug_option=native" ]]; then
-        build_release_stm32f1_native_debug;
-    elif [[ "$BOARD" =~ ":STM32F1:multistm32f103cb:debug_option=ftdi" ]]; then
-        build_release_stm32f1_serial_debug;
-    elif [[ "$BOARD" =~ ":STM32F1:multi5in1t18int" ]]; then
+    elif [[ "$RELEASE" == "stm32f103-128k-4in1" ]]; then
+        build_release_stm32f1_4in1_no_debug;
+    elif [[ "$RELEASE" == "stm32f103-128k-usb-debug" ]]; then
+        build_release_stm32f1_4in1_native_debug;
+    elif [[ "$RELEASE" == "stm32f103-128k-serial-debug" ]]; then
+        build_release_stm32f1_4in1_serial_debug;
+    elif [[ "$RELEASE" == "stm32f103-cc2500-64k" ]]; then
+        build_release_stm32f1_cc2500_64k;
+    elif [[ "$RELEASE" == "stm32f103-cc2500-128k" ]]; then
+        build_release_stm32f1_cc2500_128k;
+    elif [[ "$RELEASE" == "stm32f103-128k-5in1" ]]; then
+        build_release_stm32f1_5in1;
+    elif [[ "$RELEASE" == "tlite-5in1" ]]; then
+        build_release_stm32f1_tlite;
+    elif [[ "$RELEASE" == "t18-5in1" ]]; then
         build_release_stm32f1_t18int;
-    elif [[ "$BOARD" =~ ":STM32F1:multistm32f103c8:debug_option=none" ]]; then
-        build_release_stm32f1_64k;
     else
       printf "No release files for this board.";
     fi

buildroot/bin/build_release_stm32f1_4in1_no_debug

@@ -0,0 +1,97 @@
+#!/usr/bin/env bash
+
+source ./buildroot/bin/buildFunctions;
+exitcode=0;
+
+# Generic 4-in-1 AIR builds
+printf "\e[33;1mBuilding mm-stm-serial-aetr-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_add MULTI_AIR
+opt_disable ENABLE_PPM;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-aetr-air-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-serial-taer-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-taer-air-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-serial-reta-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-reta-air-v$MULTI_VERSION.bin;
+
+# Generic 4-in-1 SURFACE builds
+printf "\e[33;1mBuilding mm-stm-serial-aetr-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace RETA AETR;
+opt_remove MULTI_AIR;
+opt_add MULTI_SURFACE;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-aetr-sfc-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-serial-taer-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-taer-sfc-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-serial-reta-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-reta-sfc-v$MULTI_VERSION.bin;
+
+# Generic 4-in-1 LBT/EU builds
+printf "\e[33;1mBuilding mm-stm-serial-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace RETA AETR;
+opt_remove MULTI_SURFACE;
+opt_add MULTI_EU;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-aetr-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-serial-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-taer-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-serial-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-reta-lbt-v$MULTI_VERSION.bin;
+
+# 4-in-1 PPM builds
+printf "\e[33;1mBuilding mm-stm-ppm-aetr-v$MULTI_VERSION.bin\e[0m\n";
+opt_add MULTI_AIR;
+opt_enable A7105_INSTALLED;
+opt_enable CYRF6936_INSTALLED;
+opt_enable NRF24L01_INSTALLED;
+opt_remove MULTI_EU;
+opt_enable ENABLE_PPM;
+opt_disable ENABLE_SERIAL;
+opt_replace RETA AETR;
+opt_disable MULTI_STATUS;
+opt_disable MULTI_TELEMETRY;
+opt_set NBR_BANKS 5;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-ppm-aetr-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-ppm-taer-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-ppm-taer-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-ppm-reta-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-ppm-reta-v$MULTI_VERSION.bin; 
+
+exit $exitcode;

buildroot/bin/build_release_stm32f1_5in1

@@ -0,0 +1,71 @@
+#!/usr/bin/env bash
+
+source ./buildroot/bin/buildFunctions;
+exitcode=0;
+
+# DIY 5-in-1 AIR builds
+printf "\e[33;1mBuilding mm-stm-5in1-aetr-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_add MULTI_AIR;
+opt_disable ENABLE_PPM;
+opt_disable CFLIE_NRF24L01_INO
+opt_enable SX1276_INSTALLED;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-aetr-air-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-5in1-taer-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-taer-air-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-5in1-reta-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-reta-air-v$MULTI_VERSION.bin;
+
+# DIY 5-in-1 SURFACE builds
+printf "\e[33;1mBuilding mm-stm-5in1-aetr-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_add MULTI_SURFACE;
+opt_remove MULTI_AIR;
+opt_enable CFLIE_NRF24L01_INO
+opt_replace RETA AETR;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-aetr-sfc-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-5in1-taer-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-taer-sfc-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-5in1-reta-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-reta-sfc-v$MULTI_VERSION.bin;
+
+# DIY 5-in-1 LBT builds
+printf "\e[33;1mBuilding mm-stm-5in1-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_remove MULTI_SURFACE;
+opt_add MULTI_EU;
+opt_replace RETA AETR;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-aetr-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-5in1-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-taer-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-5in1-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-reta-lbt-v$MULTI_VERSION.bin;
+
+exit $exitcode;

buildroot/bin/build_release_stm32f1_cc2500_128k

@@ -0,0 +1,49 @@
+#!/usr/bin/env bash
+
+source ./buildroot/bin/buildFunctions;
+exitcode=0;
+
+# CC2500-only FCC builds
+printf "\e[33;1mBuilding mm-stm-cc2500-aetr-v$MULTI_VERSION.bin\e[0m\n";
+opt_disable A7105_INSTALLED;
+opt_disable CYRF6936_INSTALLED;
+opt_disable NRF24L01_INSTALLED;
+opt_disable ENABLE_PPM;
+opt_disable INVERT_TELEMETRY;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-aetr-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-cc2500-taer-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-taer-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-cc2500-reta-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-reta-v$MULTI_VERSION.bin;
+
+# CC2500-only LBT/EU builds
+printf "\e[33;1mBuilding mm-stm-cc2500-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace RETA AETR;
+opt_add MULTI_EU;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-aetr-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-cc2500-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-taer-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-stm-cc2500-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-reta-lbt-v$MULTI_VERSION.bin;
+
+exit $exitcode;

buildroot/bin/build_release_stm32f1_cc2500_64k

@@ -5,8 +5,8 @@ exitcode=0;
 
 # CC2500-only 64Kb FCC builds
 printf "\e[33;1mBuilding mm-stm-cc2500-64-aetr-v$MULTI_VERSION.bin\e[0m\n";
-opt_enable $ALL_PROTOCOLS;
-opt_disable IKEAANSLUTA_CC2500_INO;
+#opt_enable $ALL_PROTOCOLS;
+#opt_disable IKEAANSLUTA_CC2500_INO;
 opt_disable ENABLE_PPM;
 opt_disable A7105_INSTALLED;
 opt_disable CYRF6936_INSTALLED;

buildroot/bin/build_release_stm32f1_no_debug

@@ -1,160 +0,0 @@
-#!/usr/bin/env bash
-
-source ./buildroot/bin/buildFunctions;
-exitcode=0;
-
-# Generic 4-in-1 FCC builds
-printf "\e[33;1mBuilding mm-stm-serial-aetr-v$MULTI_VERSION.bin\e[0m\n";
-opt_disable ENABLE_PPM;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-aetr-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-serial-taer-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace AETR TAER;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-taer-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-serial-reta-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace TAER RETA;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-reta-v$MULTI_VERSION.bin;
-
-# Generic 4-in-1 LBT/EU builds
-printf "\e[33;1mBuilding mm-stm-serial-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace RETA AETR;
-opt_add MULTI_EU;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-aetr-lbt-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-serial-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace AETR TAER;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-taer-lbt-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-serial-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace TAER RETA;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-serial-reta-lbt-v$MULTI_VERSION.bin;
-
-# DIY 5-in-1 builds
-printf "\e[33;1mBuilding mm-stm-5in1-aetr-v$MULTI_VERSION.bin\e[0m\n";
-opt_remove MULTI_EU;
-opt_replace RETA AETR;
-opt_enable SX1276_INSTALLED;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-aetr-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-5in1-taer-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace AETR TAER;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-taer-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-5in1-reta-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace TAER RETA;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-5in1-reta-v$MULTI_VERSION.bin;
-
-# T-Lite 5-in-1 builds
-printf "\e[33;1mBuilding mm-tlite5in1-aetr-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace RETA AETR;
-opt_disable INVERT_TELEMETRY;
-opt_disable SX1276_INSTALLED;
-opt_enable "MULTI_5IN1_INTERNAL JP_TLite"
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-aetr-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-tlite5in1-taer-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace AETR TAER;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-taer-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-tlite5in1-reta-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace TAER RETA;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-reta-v$MULTI_VERSION.bin;
-
-# CC2500-only FCC builds
-printf "\e[33;1mBuilding mm-stm-cc2500-aetr-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace RETA AETR;
-opt_disable "MULTI_5IN1_INTERNAL JP_TLite"
-opt_disable A7105_INSTALLED;
-opt_disable CYRF6936_INSTALLED;
-opt_disable NRF24L01_INSTALLED;
-opt_disable INVERT_TELEMETRY;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-aetr-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-cc2500-taer-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace AETR TAER;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-taer-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-cc2500-reta-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace TAER RETA;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-reta-v$MULTI_VERSION.bin;
-
-# CC2500-only LBT/EU builds
-printf "\e[33;1mBuilding mm-stm-cc2500-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace RETA AETR;
-opt_add MULTI_EU;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-aetr-lbt-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-cc2500-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace AETR TAER;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-taer-lbt-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-cc2500-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace TAER RETA;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-cc2500-reta-lbt-v$MULTI_VERSION.bin;
-
-# 4-in-1 PPM builds
-printf "\e[33;1mBuilding mm-stm-ppm-aetr-v$MULTI_VERSION.bin\e[0m\n";
-opt_enable A7105_INSTALLED;
-opt_enable CYRF6936_INSTALLED;
-opt_enable NRF24L01_INSTALLED;
-opt_remove MULTI_EU;
-opt_enable ENABLE_PPM;
-opt_disable ENABLE_SERIAL;
-opt_replace RETA AETR;
-opt_disable MULTI_STATUS;
-opt_disable MULTI_TELEMETRY;
-opt_set NBR_BANKS 5;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-ppm-aetr-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-ppm-taer-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace AETR TAER;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-ppm-taer-v$MULTI_VERSION.bin;
-
-printf "\e[33;1mBuilding mm-stm-ppm-reta-v$MULTI_VERSION.bin\e[0m\n";
-opt_replace TAER RETA;
-buildMulti;
-exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-stm-ppm-reta-v$MULTI_VERSION.bin; 
-
-exit $exitcode;

buildroot/bin/build_release_stm32f1_t18int

@@ -3,23 +3,65 @@
 source ./buildroot/bin/buildFunctions;
 exitcode=0;
 
-printf "\e[33;1mBuilding mm-t18int-aetr-v$MULTI_VERSION.bin\e[0m\n";
+# T18 5-in-1 AIR builds
+printf "\e[33;1mBuilding mm-t18int-aetr-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_add MULTI_AIR
 opt_disable ENABLE_PPM;
 opt_disable INVERT_TELEMETRY;
 buildMulti;
 exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-aetr-v$MULTI_VERSION.bin;
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-aetr-air-v$MULTI_VERSION.bin;
 
-printf "\e[33;1mBuilding mm-t18int-taer-v$MULTI_VERSION.bin\e[0m\n";
+printf "\e[33;1mBuilding mm-t18int-taer-air-v$MULTI_VERSION.bin\e[0m\n";
 opt_replace AETR TAER;
 buildMulti;
 exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-taer-v$MULTI_VERSION.bin;
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-taer-air-v$MULTI_VERSION.bin;
 
-printf "\e[33;1mBuilding mm-t18int-reta-v$MULTI_VERSION.bin\e[0m\n";
+printf "\e[33;1mBuilding mm-t18int-reta-air-v$MULTI_VERSION.bin\e[0m\n";
 opt_replace TAER RETA;
 buildMulti;
 exitcode=$((exitcode+$?));
-mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-reta-v$MULTI_VERSION.bin;
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-reta-air-v$MULTI_VERSION.bin;
+
+# T18 5-in-1 SURFACE builds
+printf "\e[33;1mBuilding mm-t18int-aetr-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_remove MULTI_AIR
+opt_add MULTI_SURFACE
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-aetr-sfc-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-t18int-taer-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-taer-sfc-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-t18int-reta-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-reta-sfc-v$MULTI_VERSION.bin;
+
+# T18 5-in-1 LBT/EU builds
+printf "\e[33;1mBuilding mm-t18int-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_remove MULTI_SURFACE
+opt_add MULTI_EU
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-aetr-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-t18int-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-taer-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-t18int-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-t18int-reta-lbt-v$MULTI_VERSION.bin;
 
 exit $exitcode;

buildroot/bin/build_release_stm32f1_tlite

@@ -0,0 +1,70 @@
+#!/usr/bin/env bash
+
+source ./buildroot/bin/buildFunctions;
+exitcode=0;
+
+# T-Lite 5-in-1 AIR builds
+printf "\e[33;1mBuilding mm-tlite5in1-aetr-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_add MULTI_AIR;
+opt_disable ENABLE_PPM;
+opt_disable INVERT_TELEMETRY;
+opt_enable "MULTI_5IN1_INTERNAL JP_TLite"
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-aetr-air-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-tlite5in1-taer-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-taer-air-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-tlite5in1-reta-air-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-reta-air-v$MULTI_VERSION.bin;
+
+# T-Lite 5-in-1 SURFACE builds
+printf "\e[33;1mBuilding mm-tlite5in1-aetr-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_add MULTI_SURFACE;
+opt_remove MULTI_AIR;
+opt_replace RETA AETR;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-aetr-sfc-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-tlite5in1-taer-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-taer-sfc-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-tlite5in1-reta-sfc-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-reta-sfc-v$MULTI_VERSION.bin;
+
+# T-Lite 5-in-1 SURFACE builds
+printf "\e[33;1mBuilding mm-tlite5in1-aetr-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_remove MULTI_SURFACE;
+opt_add MULTI_EU;
+opt_replace RETA AETR;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-aetr-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-tlite5in1-taer-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace AETR TAER;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-taer-lbt-v$MULTI_VERSION.bin;
+
+printf "\e[33;1mBuilding mm-tlite5in1-reta-lbt-v$MULTI_VERSION.bin\e[0m\n";
+opt_replace TAER RETA;
+buildMulti;
+exitcode=$((exitcode+$?));
+mv build/Multiprotocol.ino.bin ./binaries/mm-tlite5in1-reta-lbt-v$MULTI_VERSION.bin;
+
+exit $exitcode;