Update SGF22_nrf24l01.ino

Fix tx and freq for none CX10

Multiprotocol/DSM_cyrf6936.ino

@@ -292,7 +292,7 @@ uint16_t DSM_callback()
 	#define DSM_CH1_CH2_DELAY	4010			// Time between write of channel 1 and channel 2
 	#ifdef STM32_BOARD
 		#define DSM_WRITE_DELAY		1600		// Time after write to verify write complete
-		#define DSM_READ_DELAY		400			// Time before write to check read phase, and switch channels.
+		#define DSM_READ_DELAY		300			// Time before write to check read phase, and switch channels.
 	#else
 		#define DSM_WRITE_DELAY		1950		// Time after write to verify write complete
 		#define DSM_READ_DELAY		600			// Time before write to check read phase, and switch channels.
@@ -470,15 +470,15 @@ uint16_t DSM_callback()
 		case DSM_CH2_READ_B:
 			//Read telemetry
 			rx_phase = CYRF_ReadRegister(CYRF_07_RX_IRQ_STATUS);
-			debug("ST1:%02X ",rx_phase);
+			//debug("ST1:%02X ",rx_phase);
 			if((rx_phase & 0x03) == 0x02)  					// RXC=1, RXE=0 then 2nd check is required (debouncing)
 				rx_phase |= CYRF_ReadRegister(CYRF_07_RX_IRQ_STATUS);
-			debug("ST2:%02X ",rx_phase);
+			//debug("ST2:%02X ",rx_phase);
 			if((rx_phase & 0x07) == 0x02)
 			{ // good data (complete with no errors)
 				CYRF_WriteRegister(CYRF_07_RX_IRQ_STATUS, 0x80);	// need to set RXOW before data read
 				length=CYRF_ReadRegister(CYRF_09_RX_COUNT);
-				debug("RX(%d)",length);
+				//debug("RX(%d)",length);
 				if(length>TELEMETRY_BUFFER_SIZE-2)
 					length=TELEMETRY_BUFFER_SIZE-2;
 				CYRF_ReadDataPacketLen(packet_in+1, length);
@@ -496,7 +496,7 @@ uint16_t DSM_callback()
 				//	debug(" %02X", packet_in[i]);
 				telemetry_link=1;
 			}
-			debugln("");
+			//debugln("");
 			CYRF_WriteRegister(CYRF_29_RX_ABORT, 0x20);		// Abort RX operation
 			if (phase == DSM_CH2_READ_A && (sub_protocol==DSM2_1F || sub_protocol==DSMX_1F) && num_ch < 8)	// 22ms mode
 			{

Multiprotocol/MT99xx_ccnrf.ino

@@ -530,7 +530,7 @@ void MT99XX_init(void)
     bind_counter = MT99XX_BIND_COUNT;
 	if(IS_BIND_DONE)
 	{		
-		if(sub_protocol != A180 && sub_protocol != DRAGON && sub_protocol != F949G && sub_protocol != PA18+8)
+		if(sub_protocol != A180 && sub_protocol != DRAGON && sub_protocol != F949G && sub_protocol != PA18+8 && sub_protocol != SU35+8)
 			BIND_IN_PROGRESS;	// autobind protocol
 		else
 		    bind_counter = 1;

Multiprotocol/Multi_Protos.ino

@@ -118,6 +118,7 @@ const char STR_UDIRC[]      ="UDIRC";
 const char STR_JIABAILE[]   ="JIABAILE";
 const char STR_KAMTOM[]     ="KAMTOM";
 const char STR_WL91X[]      ="WL91x";
+const char STR_WPL[]        ="WPL";
 
 const char STR_SUBTYPE_FLYSKY[] =     "\x04""Std\0""V9x9""V6x6""V912""CX20";
 const char STR_SUBTYPE_HUBSAN[] =     "\x04""H107""H301""H501";
@@ -188,7 +189,7 @@ const char STR_SUBTYPE_MOULDKG[] =    "\x05""A4444""D4444""A664\0";
 const char STR_SUBTYPE_KF606[] =      "\x06""KF606\0""MIG320""ZCZ50\0";
 const char STR_SUBTYPE_E129[] =       "\x04""E129""C186";
 const char STR_SUBTYPE_FX[] =         "\x05""816\0 ""620\0 ""9630\0""Q560\0""QF012";
-const char STR_SUBTYPE_SGF22[] =      "\x04""F22\0""F22S""J20\0";
+const char STR_SUBTYPE_SGF22[] =      "\x04""F22\0""F22S""J20\0""CX10";
 const char STR_SUBTYPE_JIABAILE[] =   "\x04""Std\0""Gyro";
 #define NO_SUBTYPE		nullptr
 
@@ -473,7 +474,7 @@ const mm_protocol_definition multi_protocols[] = {
 		{PROTO_SCORPIO,    STR_SCORPIO,   NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_CYRF,   SCORPIO_init,    SCORPIO_callback    },
 	#endif
 	#if defined(SGF22_NRF24L01_INO)
-		{PROTO_SGF22,      STR_SGF22,     STR_SUBTYPE_SGF22,     3, OPTION_NONE,    0, 0, SW_NRF,    SGF22_init,      SGF22_callback      },
+		{PROTO_SGF22,      STR_SGF22,     STR_SUBTYPE_SGF22,     4, OPTION_NONE,    0, 0, SW_NRF,    SGF22_init,      SGF22_callback      },
 	#endif
 	#if defined(SHENQI_NRF24L01_INO)
 		{PROTO_SHENQI,     STR_SHENQI,    NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    SHENQI_init,     SHENQI_callback     },
@@ -518,7 +519,9 @@ const mm_protocol_definition multi_protocols[] = {
 	#if defined(WL91X_CCNRF_INO)
 		{PROTO_WL91X,      STR_WL91X,     NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    WL91X_init,      WL91X_callback      },
 	#endif
-	
+	#if defined(WPL_NRF24L01_INO)
+		{PROTO_WPL,        STR_WPL,       NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    WPL_init,        WPL_callback        },
+	#endif
 	#if defined(XERALL_NRF24L01_INO)
 		{PROTO_XERALL,     STR_XERALL,    NO_SUBTYPE,            0, OPTION_NONE,    0, 0, SW_NRF,    XERALL_init,     XERALL_callback     },	
 	#endif

Multiprotocol/Multiprotocol.h

@@ -19,7 +19,7 @@
 #define VERSION_MAJOR		1
 #define VERSION_MINOR		3
 #define VERSION_REVISION	4
-#define VERSION_PATCH_LEVEL	49
+#define VERSION_PATCH_LEVEL	52
 
 #define MODE_SERIAL 0
 
@@ -134,6 +134,7 @@ enum PROTOCOLS
 	PROTO_KAMTOM	= 104,	// =>NRF24L01
 	PROTO_SHENQI2	= 105,	// =>NRF24L01
 	PROTO_WL91X		= 106,	// =>CC2500 & NRF24L01
+	PROTO_WPL		= 107,	// =>NRF24L01
 	
 	PROTO_NANORF	= 126,	// =>NRF24L01
 	PROTO_TEST		= 127,	// =>CC2500
@@ -498,6 +499,7 @@ enum SGF22
 	SGF22_F22		= 0,
 	SGF22_F22S		= 1,
 	SGF22_J20 		= 2,
+	SGF22_CX10		= 3,
 };
 enum JIABAILE
 {

Multiprotocol/RadioLink_cc2500.ino

@@ -232,7 +232,7 @@ static void __attribute__((unused)) RLINK_send_packet()
 			packet[1] |= 0x21;					//air 0x21 on dump but it looks to support telemetry at least RSSI
 			break;
 		case RLINK_DUMBORC:
-			packet[1]  = 0x00;					//always 0x00 on dump
+			packet[1] |= 0x01;					//always 0x00 on dump but does appear to support telemtry on newer transmitters
 			break;
 	}
 	
@@ -384,8 +384,9 @@ uint16_t RLINK_callback()
 					debug("Telem:");
 				#endif
 				CC2500_ReadData(packet_in, len);
-				if(packet_in[0]==RLINK_RX_PACKET_LEN && (packet_in[len-1] & 0x80) && memcmp(&packet[2],rx_tx_addr,RLINK_TX_ID_LEN)==0 && packet_in[6]==packet[1])
+				if(packet_in[0]==RLINK_RX_PACKET_LEN && (packet_in[len-1] & 0x80) && memcmp(&packet[2],rx_tx_addr,RLINK_TX_ID_LEN)==0 && (packet_in[6]==packet[1] || sub_protocol == RLINK_DUMBORC))
 				{//Correct telemetry received: length, CRC, ID and type
+				 //packet_in[6] is 0x00 on almost all DumboRC RX so assume it is always valid
 					#ifdef RLINK_DEBUG_TELEM
 						for(uint8_t i=0;i<len;i++)
 							debug(" %02X",packet_in[i]);

Multiprotocol/SGF22_nrf24l01.ino

@@ -19,14 +19,16 @@ Multiprotocol is distributed in the hope that it will be useful,
 #include "iface_xn297.h"
 
 //#define FORCE_SGF22_ORIGINAL_ID
+#define FORCE_SGF22_CX10_ORIGINAL_ID
 
 #define SGF22_PACKET_PERIOD				11950 //10240
-#define SGF22_BIND_RF_CHANNEL			78
 #define SGF22_PAYLOAD_SIZE				12
 #define SGF22_BIND_COUNT				50
 #define SGF22_RF_NUM_CHANNELS			4
+#define SGF22_BIND_RF_CHANNEL			78
 #define SGF22_F22S_BIND_RF_CHANNEL		10
 #define SGF22_J20_BIND_RF_CHANNEL  		28
+#define SGF22_CX10_BIND_RF_CHANNEL		48
 
 //packet[8]
 #define SGF22_FLAG_3D					0x00
@@ -49,7 +51,6 @@ Multiprotocol is distributed in the hope that it will be useful,
 #define SGF22_J20_FLAG_FIXHEIGHT		0x80
 
 #define SGF22_WRITE_TIME				1000
-//#define SGF22_HUB_TELEMETRY
 
 enum {
 	SGF22_DATA1,
@@ -80,6 +81,8 @@ static void __attribute__((unused)) SGF22_send_packet()
 			packet_sent = 0;
 		//packet
 		packet[0] = 0x1B;
+		if (sub_protocol != SGF22_CX10)
+		{//SGF22_F22,SGF22_F22S,SGF22_J20
 			packet[8] = SGF22_FLAG_3D           			// CH5 -100%, F22 & F22S - 3D mode, J20 - Gyro off  
 				| GET_FLAG(CH6_SW, SGF22_FLAG_ROLL)			// roll
 				| GET_FLAG(CH7_SW, SGF22_FLAG_LIGHT)		// push up throttle trim for light in the stock TX
@@ -90,6 +93,19 @@ static void __attribute__((unused)) SGF22_send_packet()
 				packet[8] |= SGF22_FLAG_VERTICAL;     		// CH5 100%,  vertical mode (torque)    
 			else if(Channel_data[CH5] > CHANNEL_MIN_COMMAND )
 			packet[8] |= ( sub_protocol == SGF22_J20 ? SGF22_J20_FLAG_HORIZONTAL : SGF22_FLAG_6G );     // CH5 0%, F22 & F22S - 6G mode, J20 - Horizontal mode
+		}
+		else //SGF22_CX10 114548
+		{
+			if(CH6_SW)
+				flags = 0x06;								// high rate
+			else
+				if(Channel_data[CH6] < CHANNEL_MIN_COMMAND)
+					flags = 0x04;							// low rate
+				else
+					flags = 0x05;							// mid rate
+			packet[8] = flags
+				| GET_FLAG(CH5_SW, 0x08);					// flip
+		}
 		packet[9] = GET_FLAG(CH8_SW, SGF22_FLAG_PHOTO)		// F22: photo, press in throttle trim in the stock TX, J20: invert flight
 			| GET_FLAG(CH10_SW, ( sub_protocol == SGF22_J20 ? SGF22_J20_FLAG_FIXHEIGHT : SGF22_FLAG_TRIMRESET )) ;   // F22: Both sticks down inwards in the stock TX, J20: Altitude hold
 		packet[10] = 0x42;									// no fine tune
@@ -99,6 +115,8 @@ static void __attribute__((unused)) SGF22_send_packet()
 		packet[0] += 6;
 	else if (sub_protocol == SGF22_J20)
     		packet[0] += 3; 
+	else if (sub_protocol == SGF22_CX10)
+    		packet[0] += 0x6A; 
 	packet[1] = packet_count;								// sequence
 	packet[2] = rx_tx_addr[2];
 	packet[3] = rx_tx_addr[3];
@@ -109,7 +127,10 @@ static void __attribute__((unused)) SGF22_send_packet()
 
 	XN297_SetPower();
 	XN297_SetTxRxMode(TX_EN);
+	if (sub_protocol != SGF22_CX10)
 		XN297_WriteEnhancedPayload(packet, SGF22_PAYLOAD_SIZE,0);
+	else
+		XN297_WritePayload(packet, SGF22_PAYLOAD_SIZE);
 	#if 0
 		debug_time("");
 		for(uint8_t i=0; i<SGF22_PAYLOAD_SIZE; i++)
@@ -133,7 +154,7 @@ static void __attribute__((unused)) SGF22_initialize_txid()
 	  { 0x18, 0x37, 0x27, 0x47 } };
 	memcpy(hopping_frequency, &hop[val], SGF22_RF_NUM_CHANNELS);
 
-	/*//Same code sze...
+	/*//Same code size...
 	hopping_frequency[0] = 0x0C + 3 * val;
 	hopping_frequency[1] = hopping_frequency[0] + 0x1E;
 	if(val > 1) hopping_frequency[1]++;
@@ -146,6 +167,23 @@ static void __attribute__((unused)) SGF22_initialize_txid()
 		rx_tx_addr[3] = 0x61;	// TX2:51 TX3:0C
 		memcpy(hopping_frequency,"\x15\x34\x24\x44", SGF22_RF_NUM_CHANNELS);    //Original dump=>21=0x15,52=0x34,36=0x24,68=0x44
 	#endif
+	#ifdef FORCE_SGF22_CX10_ORIGINAL_ID
+		if(sub_protocol == SGF22_CX10)
+		{
+			if(rx_tx_addr[3] & 1)
+			{
+				rx_tx_addr[2] = 0x4C;
+				rx_tx_addr[3] = 0xD7;
+				memcpy(hopping_frequency, "\x37\x42\x47\x3c", SGF22_RF_NUM_CHANNELS);
+			}
+			else
+			{
+				rx_tx_addr[2] = 0x50;
+				rx_tx_addr[3] = 0xE1;
+				memcpy(hopping_frequency, "\x3b\x4b\x46\x41", SGF22_RF_NUM_CHANNELS);
+			}
+		}
+	#endif
 	#if 0
 		debug("ID: %02X %02X, C: ",rx_tx_addr[2],rx_tx_addr[3]);
 		for(uint8_t i=0; i<SGF22_RF_NUM_CHANNELS; i++)
@@ -162,7 +200,7 @@ static void __attribute__((unused)) SGF22_RF_init()
 		XN297_SetRXAddr((uint8_t*)"\xC7\x95\x3C\xBB\xA5", SGF22_PAYLOAD_SIZE);
 	#endif
 
-	const uint8_t bind_chan[] = {SGF22_BIND_RF_CHANNEL, SGF22_F22S_BIND_RF_CHANNEL, SGF22_J20_BIND_RF_CHANNEL}; 
+	const uint8_t bind_chan[] = {SGF22_BIND_RF_CHANNEL, SGF22_F22S_BIND_RF_CHANNEL, SGF22_J20_BIND_RF_CHANNEL, SGF22_CX10_BIND_RF_CHANNEL};
 	XN297_RFChannel(bind_chan[sub_protocol]);	// Set bind channel
 }
 
@@ -170,6 +208,7 @@ uint16_t SGF22_callback()
 {
 	#ifdef SGF22_HUB_TELEMETRY
 		bool rx = false;
+		static uint8_t telem_count = 0;
 	#endif
 
 	switch(phase)
@@ -193,9 +232,11 @@ uint16_t SGF22_callback()
 			{
 				uint8_t p_len = XN297_ReadEnhancedPayload(packet_in, SGF22_PAYLOAD_SIZE);
 				if(p_len == 3 && packet_in[0] == rx_tx_addr[2] && packet_in[1] == rx_tx_addr[3])
-				{//packets only received when battery is low: 00 0B 01
+				{//packets: 00 0B 00 -> 00 0B 01
 					telemetry_link = 1;
-					v_lipo1 = packet_in[2] ? 0 : 255;
+					v_lipo1 = packet_in[2] ? 0 : 255;	//2.9V for 1S, 7.0V for 2S
+					telemetry_lost = 0;
+					telem_count = 0;
 				}
 				#if 0
 					debug("L %d ",p_len);
@@ -205,6 +246,20 @@ uint16_t SGF22_callback()
 					debugln("");
 				#endif
 			}
+			if(telem_count > 4*63)				// Around 3.5sec with no telemetry
+				telemetry_lost = 1;
+			else
+			{
+				telem_count++;
+				if(!telemetry_lost && (telem_count & 0x3F) == 0)
+				{// Should have received a telem packet but... Send telem to the radio to keep it alive
+					telemetry_link = 1;
+					#if 0
+						debugln("Miss");
+					#endif
+				}
+			}
+
 	#endif
 			phase++;
 			break;
@@ -246,6 +301,7 @@ void SGF22_init()
 	phase = SGF22_DATA1;
 	#ifdef SGF22_HUB_TELEMETRY
 		RX_RSSI = 100;		// Dummy value
+		telemetry_lost = 1;
 	#endif
 }
 

Multiprotocol/V761_nrf24l01.ino

@@ -244,7 +244,7 @@ uint16_t V761_callback()
 			else
 			{
 				packet_count++;
-				if(!telemetry_lost && !rx && (packet_count%64) == 0)
+				if(!telemetry_lost && !rx && (packet_count & 0x3F) == 0)
 				{// Should have received a telem packet but... Send telem to the radio to keep it alive
 					telemetry_link = 1;
 					#ifdef V761_TELEM_DEBUG

Multiprotocol/Validate.h

@@ -341,6 +341,7 @@
 	#undef	SYMAX_NRF24L01_INO
 	#undef	V2X2_NRF24L01_INO
 	#undef	V761_NRF24L01_INO
+	#undef	WPL_NRF24L01_INO
 	#undef	XERALL_NRF24L01_INO
 	#undef	YD717_NRF24L01_INO
 	#undef	YUXIANG_NRF24L01_INO
@@ -399,6 +400,7 @@
 	#undef	UDIRC_CCNRF_INO
 	#undef	KAMTOM_NRF24L01_INO
 	#undef	WL91X_CCNRF_INO
+	#undef	WPL_NRF24L01_INO
 	//Save flash space...
 	#undef	CABELL_NRF24L01_INO
 	#undef	REDPINE_CC2500_INO
@@ -499,6 +501,7 @@
 	#undef V761_HUB_TELEMETRY
 	#undef FX_HUB_TELEMETRY
 	#undef XK2_HUB_TELEMETRY
+	#undef SGF22_HUB_TELEMETRY
 	#undef KAMTOM_HUB_TELEMETRY
 	#undef YUXIANG_HUB_TELEMETRY
 	#undef RLINK_HUB_TELEMETRY
@@ -545,6 +548,9 @@
 	#if not defined(XK2_CCNRF_INO)
 		#undef XK2_HUB_TELEMETRY
 	#endif
+	#if not defined(SGF22_NRF24L01_INO)
+		#undef SGF22_HUB_TELEMETRY
+	#endif
 	#if not defined(KAMTOM_NRF24L01_INO)
 		#undef KAMTOM_HUB_TELEMETRY
 	#endif
@@ -608,7 +614,7 @@
 		//protocols using FRSKYD user frames
 		#undef HUB_TELEMETRY 
 	#endif
-	#if not defined(HOTT_FW_TELEMETRY) && not defined(DSM_TELEMETRY) && not defined(SPORT_TELEMETRY) && not defined(HUB_TELEMETRY) && not defined(HUBSAN_HUB_TELEMETRY) && not defined(BUGS_HUB_TELEMETRY) && not defined(NCC1701_HUB_TELEMETRY) && not defined(BAYANG_HUB_TELEMETRY) && not defined(CABELL_HUB_TELEMETRY) && not defined(RLINK_HUB_TELEMETRY) && not defined(AFHDS2A_HUB_TELEMETRY) && not defined(AFHDS2A_FW_TELEMETRY) && not defined(MULTI_TELEMETRY) && not defined(MULTI_STATUS) && not defined(HITEC_HUB_TELEMETRY) && not defined(HITEC_FW_TELEMETRY) && not defined(SCANNER_TELEMETRY) && not defined(FRSKY_RX_TELEMETRY) && not defined(AFHDS2A_RX_TELEMETRY) && not defined(BAYANG_RX_TELEMETRY) && not defined(DEVO_HUB_TELEMETRY) && not defined(PROPEL_HUB_TELEMETRY) && not defined(OMP_HUB_TELEMETRY) && not defined(V761_HUB_TELEMETRY) && not defined(XK2_HUB_TELEMETRY) && not defined(FX_HUB_TELEMETRY) && not defined(KAMTOM_HUB_TELEMETRY) && not defined(YUXIANG_HUB_TELEMETRY) && not defined(WFLY2_HUB_TELEMETRY) && not defined(LOLI_HUB_TELEMETRY) && not defined(MLINK_HUB_TELEMETRY) && not defined(MLINK_FW_TELEMETRY) && not defined(MT99XX_HUB_TELEMETRY) && not defined(MULTI_CONFIG_INO)
+	#if not defined(HOTT_FW_TELEMETRY) && not defined(DSM_TELEMETRY) && not defined(SPORT_TELEMETRY) && not defined(HUB_TELEMETRY) && not defined(HUBSAN_HUB_TELEMETRY) && not defined(BUGS_HUB_TELEMETRY) && not defined(NCC1701_HUB_TELEMETRY) && not defined(BAYANG_HUB_TELEMETRY) && not defined(CABELL_HUB_TELEMETRY) && not defined(RLINK_HUB_TELEMETRY) && not defined(AFHDS2A_HUB_TELEMETRY) && not defined(AFHDS2A_FW_TELEMETRY) && not defined(MULTI_TELEMETRY) && not defined(MULTI_STATUS) && not defined(HITEC_HUB_TELEMETRY) && not defined(HITEC_FW_TELEMETRY) && not defined(SCANNER_TELEMETRY) && not defined(FRSKY_RX_TELEMETRY) && not defined(AFHDS2A_RX_TELEMETRY) && not defined(BAYANG_RX_TELEMETRY) && not defined(DEVO_HUB_TELEMETRY) && not defined(PROPEL_HUB_TELEMETRY) && not defined(OMP_HUB_TELEMETRY) && not defined(V761_HUB_TELEMETRY) && not defined(SGF22_HUB_TELEMETRY) && not defined(XK2_HUB_TELEMETRY) && not defined(FX_HUB_TELEMETRY) && not defined(KAMTOM_HUB_TELEMETRY) && not defined(YUXIANG_HUB_TELEMETRY) && not defined(WFLY2_HUB_TELEMETRY) && not defined(LOLI_HUB_TELEMETRY) && not defined(MLINK_HUB_TELEMETRY) && not defined(MLINK_FW_TELEMETRY) && not defined(MT99XX_HUB_TELEMETRY) && not defined(MULTI_CONFIG_INO)
 		#undef TELEMETRY
 		#undef INVERT_TELEMETRY
 		#undef MULTI_TELEMETRY

Multiprotocol/WPL_nrf24l01.ino

@@ -0,0 +1,158 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol.  If not, see <http://www.gnu.org/licenses/>.
+ */
+// Compatible with WPL "Basic" TX models D12, D12KM, D22, D32, D42, D14
+
+#if defined(WPL_NRF24L01_INO)
+
+#include "iface_xn297.h"
+
+#define FORCE_WPL_ORIGINAL_ID
+
+#define WPL_PACKET_PERIOD   9875
+#define WPL_RF_NUM_CHANNELS 4
+#define WPL_PAYLOAD_SIZE    16
+#define WPL_BIND_COUNT		303	//3sec
+
+static void __attribute__((unused)) WPL_send_packet()
+{
+	#if 0
+		debug("no:%d, rf:%d, ",hopping_frequency_no + (IS_BIND_IN_PROGRESS?0:4),hopping_frequency[hopping_frequency_no + (IS_BIND_IN_PROGRESS?0:4)]);
+	#endif
+	XN297_Hopping(hopping_frequency_no + (IS_BIND_IN_PROGRESS?0:4) );
+	hopping_frequency_no++;
+	hopping_frequency_no &= WPL_RF_NUM_CHANNELS-1;	// 4 RF channels
+
+	memset(&packet[8],0,7);
+	packet[0] = 0x94;											//??
+	packet[1] = 0x16;											//??
+	packet[2] = 0xCC;											//??
+	
+	if(IS_BIND_IN_PROGRESS)
+	{
+		memcpy(&packet[3],rx_tx_addr,5);
+		packet[9] = 0x08;										// ?? Not bound + Headlights on
+	}
+	else
+	{
+		packet[3 ] = convert_channel_s8b(CH1);					// Throttle
+		packet[4 ] = convert_channel_s8b(CH2);					// Steering
+		packet[5 ] = convert_channel_16b_limit(CH3,0x22,0x5E);	// Steering trim
+		packet[6 ] = rx_tx_addr[3];								// 0x32??
+		packet[7 ] = convert_channel_s8b(CH4);					// Aux
+		packet[9 ] = 0x80										// ?? Bound
+				   | GET_FLAG(CH5_SW, 0x08)						// Headlights 100%=on
+				   | GET_FLAG(CH6_SW, 0x04)						// Throttle rate 100%=high
+				   | GET_FLAG(CH7_SW, 0x02);					// Steering rate 100%=high
+	}
+	uint8_t sum = 0x66;
+	for(uint8_t i=0;i<WPL_PAYLOAD_SIZE-1;i++)
+		sum += packet[i];
+	packet[WPL_PAYLOAD_SIZE-1] = sum;
+	// Send
+	XN297_SetPower();
+	XN297_SetTxRxMode(TX_EN);
+	XN297_WritePayload(packet, WPL_PAYLOAD_SIZE);
+	#if 0
+		for(uint8_t i=0; i<WPL_PAYLOAD_SIZE; i++)
+			debug(" %02X",packet[i]);
+		debugln("");
+	#endif
+}
+
+static void __attribute__((unused)) WPL_RF_init()
+{
+	XN297_Configure(XN297_CRCEN, XN297_SCRAMBLED, XN297_1M);
+	XN297_SetTXAddr((uint8_t*)"\x69\xA5\x37\x4D\x8B", 5);
+	XN297_HoppingCalib(WPL_RF_NUM_CHANNELS*2);	// Calibrate bind and normal channels
+}
+
+static void __attribute__((unused)) WPL_initialize_txid()
+{
+	//Bind frequencies
+	memcpy(hopping_frequency  ,"\x17\x25\x46\x36", WPL_RF_NUM_CHANNELS);	//23=17, 37=25, 70=46, 54=36
+	#ifdef FORCE_WPL_ORIGINAL_ID
+		//Original ID
+		memcpy(rx_tx_addr,"\x96\x2A\xA9\x32\xB4",5);
+		//Normal frequencies
+		memcpy(hopping_frequency+4,"\x0C\x2A\x3D\x1D", WPL_RF_NUM_CHANNELS);	//12=0C, 42=2A, 61=3D, 29=1D
+	#endif
+}
+
+uint16_t WPL_callback()
+{
+	#ifdef MULTI_SYNC
+		telemetry_set_input_sync(WPL_PACKET_PERIOD);
+	#endif
+	if(bind_counter)
+		if(--bind_counter==0)
+		{
+			BIND_DONE;
+			XN297_SetTXAddr(rx_tx_addr, 5);
+		}
+	WPL_send_packet();
+	return WPL_PACKET_PERIOD;
+}
+
+void WPL_init()
+{
+	BIND_IN_PROGRESS;	// autobind protocol
+	WPL_initialize_txid();
+	WPL_RF_init();
+	hopping_frequency_no = 0;
+	bind_counter=WPL_BIND_COUNT;
+}
+
+#endif
+/* https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/issues/1120
+Bind packet
+-----------
+XN297 1Mb Scrambled
+Bind address: 69 A5 37 4D 8B
+RF channels: 23, 37, 70, 54
+Timing: 9875µs
+Payload 16 bytes: 94 16 CC 96 2A A9 32 B4 00 08 00 00 00 00 00 33
+
+P[0] = 94 ??
+P[1] = 16 ??
+P[2] = CC ??
+P[3..7] = Normal address
+P[8] = 00 ??
+P[9] = 08 ?? not bound?, Throttle and Steering rate low, Headlights on
+P[10..14] = 00 ??
+P[15] = sum(P[0..14])+66 why 66...
+
+Normal packet
+-----------
+XN297 1Mb Scrambled
+Normal address: 96 2A A9 32 B4
+RF channels: 12=0C, 42=2A, 61=3D, 29=1D -> no idea where they come from...
+Timing: 9875µs
+Payload 16 bytes: 94 16 CC 80 80 38 32 80 00 88 00 00 00 00 00 4E
+P[0] = 94 ??
+P[1] = 16 ??
+P[2] = CC ??
+P[3] = Throttle, not enough data on dumps... Same coding as Steering?
+P[4] = Steering, not enough data on dumps, looks like one side goes from 7F to 00 and the other 80 to FF which would be s8b
+P[5] = Steering trim 22..5E, mid gives 40 not 38... Was the trim centered on the other dumps with value 38?
+P[6] = 32 ?? Left over from the bind packet TX_ADDR[3]?
+P[7] = 80 ?? Additional channel? It moves at the same time as the trim but my guess is that it is an unconnected channel.
+P[8] = 00 ??
+P[9] = 80 ?? bound?, Throttle and Steering rate low, Headlights off
+      |02 -> Steering rate high
+      |04 -> Throttle rate high
+      |08 -> Headlights on
+P[10..14] = 00 ??
+P[15] = sum(P[0..14])+66 why 66...
+*/

Multiprotocol/_Config.h

@@ -261,6 +261,7 @@
 #define	SYMAX_NRF24L01_INO
 #define	V2X2_NRF24L01_INO
 #define	V761_NRF24L01_INO
+#define	WPL_NRF24L01_INO
 #define	XERALL_NRF24L01_INO
 #define	YD717_NRF24L01_INO
 #define	YUXIANG_NRF24L01_INO
@@ -351,6 +352,7 @@
 #define KAMTOM_HUB_TELEMETRY		// Use FrSkyD Hub format to send telemetry to TX
 #define FX_HUB_TELEMETRY			// Use FrSkyD Hub format to send telemetry to TX
 #define XK2_HUB_TELEMETRY			// Use FrSkyD Hub format to send telemetry to TX
+#define SGF22_HUB_TELEMETRY			// Use FrSkyD Hub format to send telemetry to TX
 #define YUXIANG_HUB_TELEMETRY		// Use FrSkyD Hub format to send telemetry to TX
 #define PROPEL_HUB_TELEMETRY		// Use FrSkyD Hub format to send telemetry to TX
 #define CABELL_HUB_TELEMETRY		// Use FrSkyD Hub format to send telemetry to TX
@@ -833,6 +835,7 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 		SGF22
 		F22S
   		J20
+		CX10
 	PROTO_SHENQI
 		NONE
 	PROTO_SHENQI2
@@ -875,6 +878,8 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 		W6_6_1
 		W6_HEL
 		W6_HEL_I
+	PROTO_WPL
+		NONE
 	PROTO_XERALL
 		NONE
 	PROTO_XK

Protocols_Details.md

@@ -61,107 +61,108 @@ You've upgraded the module but the radio does not display the name of the protoc
  
 # Available Protocol Table of Contents (Listed Alphabetically)
 
-Protocol Name|Protocol Number|Sub_Proto 0|Sub_Proto 1|Sub_Proto 2|Sub_Proto 3|Sub_Proto 4|Sub_Proto 5|Sub_Proto 6|Sub_Proto 7|RF Module|Emulation
----|---|---|---|---|---|---|---|---|---|---|---
-[Assan](Protocols_Details.md#ASSAN---24)|24|||||||||NRF24L01|
-[Bayang](Protocols_Details.md#BAYANG---14)|14|Bayang|H8S3D|X16_AH|IRDRONE|DHD_D4|QX100|||NRF24L01|XN297
-[Bayang RX](Protocols_Details.md#BAYANG-RX---59)|59|Multi|CPPM|||||||NRF24L01|XN297
-[BlueFly](Protocols_Details.md#BLUEFLY---95)|95|||||||||NRF24L01|
-[Bugs](Protocols_Details.md#BUGS---41)|41|||||||||A7105|
-[BugsMini](Protocols_Details.md#BUGSMINI---42)|42|BUGSMINI|BUGS3H|||||||NRF24L01|XN297
-[Cabell](Protocols_Details.md#Cabell---34)|34|Cabell_V3|C_TELEM|-|-|-|-|F_SAFE|UNBIND|NRF24L01|
-CFlie|38|CFlie||||||||NRF24L01|
-[CG023](Protocols_Details.md#CG023---13)|13|CG023|YD829|||||||NRF24L01|XN297
-[Corona](Protocols_Details.md#CORONA---37)|37|COR_V1|COR_V2|FD_V3||||||CC2500|
-[CX10](Protocols_Details.md#CX10---12)|12|GREEN|BLUE|DM007|-|J3015_1|J3015_2|MK33041||NRF24L01|XN297
-[Devo](Protocols_Details.md#DEVO---7)|7|Devo|8CH|10CH|12CH|6CH|7CH|||CYRF6936|
-[DM002](Protocols_Details.md#DM002---33)|33|||||||||NRF24L01|XN297
-[DSM](Protocols_Details.md#DSM---6)|6|DSM2_1F|DSM2_2F|DSMX_1F|DSMX_2F|AUTO|DSMR_1F|DSM2SFC||CYRF6936|
-[DSM_RX](Protocols_Details.md#DSM_RX---70)|70|Multi|CPPM|||||||CYRF6936|
-[E010R5](Protocols_Details.md#E010R5---81)|81|||||||||CYRF6936|RF2500
-[E016H](Protocols_Details.md#E016H---85)|85|||||||||NRF24L01|XN297
-[E016HV2](Protocols_Details.md#E016HV2---80)|80|||||||||CC2500/NRF24L01|unknown
-[E01X](Protocols_Details.md#E01X---45)|45|E012|E015|||||||CYRF6936|HS6200
-[E129](Protocols_Details.md#E129---83)|83|E129|C186|||||||CYRF6936|RF2500
-[EazyRC](Protocols_Details.md#EazyRC---61)|61|||||||||NRF24L01|XN297L
-[ESky](Protocols_Details.md#ESKY---16)|16|ESky|ET4|||||||NRF24L01|
-[ESky150](Protocols_Details.md#ESKY150---35)|35|||||||||NRF24L01|
-[ESky150V2](Protocols_Details.md#ESKY150V2---69)|69|||||||||CC2500|NRF51822
-[Flysky](Protocols_Details.md#FLYSKY---1)|1|Flysky|V9x9|V6x6|V912|CX20||||A7105|
-[Flysky AFHDS2A](Protocols_Details.md#FLYSKY-AFHDS2A---28)|28|PWM_IBUS|PPM_IBUS|PWM_SBUS|PPM_SBUS|Gyro_Off|Gyro_On|Gyro_On_Rev||A7105|
-[Flysky AFHDS2A RX](Protocols_Details.md#FLYSKY-AFHDS2A-RX---56)|56|Multi|CPPM|||||||A7105|
-[FQ777](Protocols_Details.md#FQ777---23)|23|||||||||NRF24L01|SSV7241
-[FrskyD](Protocols_Details.md#FRSKYD---3)|3|D8|Cloned|||||||CC2500|
-[FrskyL](Protocols_Details.md#FRSKYL---67)|67|LR12|LR12 6CH|||||||CC2500|
-[FrskyR9](Protocols_Details.md#FRSKYR9---65)|65|FrskyR9|R9_915|R9_868||||||SX1276|
-[FrskyV](Protocols_Details.md#FRSKYV---25)|25|||||||||CC2500|
-[FrskyX](Protocols_Details.md#FRSKYX---15)|15|CH_16|CH_8|EU_16|EU_8|Cloned|Cloned_8|||CC2500|
-[FrskyX2](Protocols_Details.md#FRSKYX2---64)|64|CH_16|CH_8|EU_16|EU_8|Cloned|Cloned_8|||CC2500|
-[Frsky_RX](Protocols_Details.md#FRSKY_RX---55)|55|Multi|CloneTX|EraseTX|CPPM|||||CC2500|
-[Futaba/SFHSS](Protocols_Details.md#Futaba---21)|21|SFHSS||||||||CC2500|
-[FX](Protocols_Details.md#FX---58)|28|816|620|9630|Q560|QF012||||NRF24L01|
-[FY326](Protocols_Details.md#FY326---20)|20|FY326|FY319|||||||NRF24L01|
-[GD00X](Protocols_Details.md#GD00X---47)|47|GD_V1*|GD_V2*|||||||NRF24L01|XN297L
-[GW008](Protocols_Details.md#GW008---32)|32|||||||||NRF24L01|XN297
-[H36](Protocols_Details.md#H36---103)|H36|||||||||NRF24L01|XN297
-[H8_3D](Protocols_Details.md#H8_3D---36)|36|H8_3D|H20H|H20Mini|H30Mini|||||NRF24L01|XN297
-[Height](Protocols_Details.md#HEIGHT---53)|53|5ch|8ch|||||||A7105|
-[Hisky](Protocols_Details.md#HISKY---4)|4|Hisky|HK310|||||||NRF24L01|
-[Hitec](Protocols_Details.md#HITEC---39)|39|OPT_FW|OPT_HUB|MINIMA||||||CC2500|
-[Hontai](Protocols_Details.md#HONTAI---26)|26|HONTAI|JJRCX1|X5C1|FQ777_951|XKK170||||NRF24L01|XN297
-[HoTT](Protocols_Details.md#HoTT---57)|57|Sync|No_Sync|||||||CC2500|
-[Hubsan](Protocols_Details.md#HUBSAN---2)|2|H107|H301|H501||||||A7105|
-[J6Pro](Protocols_Details.md#J6Pro---22)|22|||||||||CYRF6936|
-[JIABAILE](Protocols_Details.md#JIABAILE---102)|102|Std|Gyro|||||||NRF24L01|XN297
-[JJRC345](Protocols_Details.md#JJRC345---71)|71|JJRC345|SkyTmblr|||||||NRF24L01|XN297
-[JOYSWAY](Protocols_Details.md#JOYSWAY---84)|84|||||||||NRF24L01|XN297
-[KAMTOM](Protocols_Details.md#KAMTOM---104)|104|||||||||NRF24L01|XN297
-[KF606](Protocols_Details.md#KF606---49)|49|KF606|MIG320|ZCZ50||||||NRF24L01|XN297
-[KN](Protocols_Details.md#KN---9)|9|WLTOYS|FEILUN|||||||NRF24L01|
-[Kyosho](Protocols_Details.md#Kyosho---73)|73|FHSS|Hype|||||||A7105|
-[Kyosho2](Protocols_Details.md#Kyosho2---93)|93|KT-17||||||||NRF24L01|
-[Kyosho3](Protocols_Details.md#Kyosho3---98)|98|ASF||||||||CYRF6936|
-[LOLI](Protocols_Details.md#LOLI---82)|82|||||||||NRF24L01|
-[Losi](Protocols_Details.md#Losi---89)|89|||||||||CYRF6936|
-[MJXq](Protocols_Details.md#MJXQ---18)|18|WLH08|X600|X800|H26D|E010*|H26WH|PHOENIX*||NRF24L01|XN297
-[MLINK](Protocols_Details.md#MLINK---78)|78|||||||||CYRF6936|
-[MouldKg](Protocols_Details.md#mouldkg---90)|90|A4444|D4444|A664||||||NRF24L01|XN297
-[MT99xx](Protocols_Details.md#MT99XX---17)|17|MT|H7|YZ|LS|FY805|A180|DRAGON|F949G|NRF24L01|XN297
-[MT99xx2](Protocols_Details.md#MT99XX2---92)|92|PA18|SU35|||||||NRF24L01|XN297
-[NCC1701](Protocols_Details.md#NCC1701---44)|44|||||||||NRF24L01|
-[OMP](Protocols_Details.md#OMP---77)|77|||||||||CC2500&NRF24L01|XN297L
-[OpenLRS](Protocols_Details.md#OpenLRS---27)|27|||||||||None|
-[Pelikan](Protocols_Details.md#Pelikan---60)|60|Pro|Lite|SCX24||||||A7105|
-[Potensic](Protocols_Details.md#Potensic---51)|51|A20||||||||NRF24L01|XN297
-[PROPEL](Protocols_Details.md#PROPEL---66)|66|74-Z||||||||NRF24L01|
-[Q2X2](Protocols_Details.md#Q2X2---29)|29|Q222|Q242|Q282||||||NRF24L01|
-[Q303](Protocols_Details.md#Q303---31)|31|Q303|CX35|CX10D|CX10WD|||||NRF24L01|XN297
-[Q90C](Protocols_Details.md#Q90C---72)|72|Q90C*||||||||NRF24L01|XN297
-[RadioLink](Protocols_Details.md#RadioLink---74)|74|Surface|Air|DumboRC|RC4G|||||CC2500|
-[Realacc](Protocols_Details.md#Realacc---76)|76|R11||||||||NRF24L01|
-[Redpine](Protocols_Details.md#Redpine---50)|50|FAST|SLOW|||||||NRF24L01|XN297
-[Scanner](Protocols_Details.md#Scanner---54)|54|||||||||CC2500|
-[Scorpio](Protocols_Details.md#Scorpio---94)|94|||||||||CYRF6936|
-[SGF22](Protocols_Details.md#SGF22---97)|97|F22|F22S|J20||||||NRF24L01|XN297
-[Shenqi](Protocols_Details.md#Shenqi---19)|19|Shenqi||||||||NRF24L01|LT8900
-[Shenqi2](Protocols_Details.md#Shenqi2---105)|105|Shenqi2||||||||NRF24L01|XN297
-[Skyartec](Protocols_Details.md#Skyartec---68)|68|||||||||CC2500|CC2500
-[SLT](Protocols_Details.md#SLT---11)|11|SLT_V1|SLT_V2|Q100|Q200|MR100|V1_4CH|RF_SIM||NRF24L01|CC2500
-[SymaX](Protocols_Details.md#Symax---10)|10|SYMAX|SYMAX5C|||||||NRF24L01|
-[Traxxas](Protocols_Details.md#Traxxas---43)|43|TQ2|TQ1|||||||CYRF6936|
-[V2x2](Protocols_Details.md#V2X2---5)|5|V2x2|JXD506|MR101||||||NRF24L01|
-[V761](Protocols_Details.md#V761---48)|48|3CH|4CH|TOPRC||||||NRF24L01|XN297
-[V911S](Protocols_Details.md#V911S---46)|46|V911S*|E119*|||||||NRF24L01|XN297
-[WFLY](Protocols_Details.md#WFLY---40)|40|WFR0x||||||||CYRF6936|
-[WFLY2](Protocols_Details.md#WFLY2---79)|79|RF20x||||||||A7105|
-[WK2x01](Protocols_Details.md#WK2X01---30)|30|WK2801|WK2401|W6_5_1|W6_6_1|W6_HEL|W6_HEL_I|||CYRF6936|
-[WL91X](Protocols_Details.md#WL91X---106)|106|||||||||NRF24L011&CC2500|XN297
-[XERALL](Protocols_Details.md#XERALL---91)|91|Tank||||||||NRF24L01|XN297
-[XK](Protocols_Details.md#XK---62)|62|X450|X420|Cars||||||NRF24L011&CC2500|XN297
-[XK2](Protocols_Details.md#XK2---99)|99|X4|P10|||||||NRF24L01&CC2500|XN297
-[YD717](Protocols_Details.md#YD717---8)|8|YD717|SKYWLKR|SYMAX4|XINXUN|NIHUI||||NRF24L01|
-[YuXiang](Protocols_Details.md#YuXiang---100)|100|||||||||NRF24L01|XN297
-[ZSX](Protocols_Details.md#ZSX---52)|52|280||||||||NRF24L01|XN297
+Protocol Name|Build|Protocol Number|Sub_Proto 0|Sub_Proto 1|Sub_Proto 2|Sub_Proto 3|Sub_Proto 4|Sub_Proto 5|Sub_Proto 6|Sub_Proto 7|RF Module|Emulation
+---|---|---|---|---|---|---|---|---|---|---|---|---
+[Assan](Protocols_Details.md#ASSAN---24)|AIR/SFC|24|||||||||NRF24L01|
+[Bayang](Protocols_Details.md#BAYANG---14)|AIR/SFC|14|Bayang|H8S3D|X16_AH|IRDRONE|DHD_D4|QX100|||NRF24L01|XN297
+[Bayang RX](Protocols_Details.md#BAYANG-RX---59)|AIR/SFC|59|Multi|CPPM|||||||NRF24L01|XN297
+[BlueFly](Protocols_Details.md#BLUEFLY---95)||95|||||||||NRF24L01|
+[Bugs](Protocols_Details.md#BUGS---41)|AIR|41|||||||||A7105|
+[BugsMini](Protocols_Details.md#BUGSMINI---42)|AIR|42|BUGSMINI|BUGS3H|||||||NRF24L01|XN297
+[Cabell](Protocols_Details.md#Cabell---34)||34|Cabell_V3|C_TELEM|-|-|-|-|F_SAFE|UNBIND|NRF24L01|
+CFlie|AIR|38|CFlie||||||||NRF24L01|
+[CG023](Protocols_Details.md#CG023---13)|AIR|13|CG023|YD829|||||||NRF24L01|XN297
+[Corona](Protocols_Details.md#CORONA---37)|AIR/SFC|37|COR_V1|COR_V2|FD_V3||||||CC2500|
+[CX10](Protocols_Details.md#CX10---12)|AIR|12|GREEN|BLUE|DM007|-|J3015_1|J3015_2|MK33041||NRF24L01|XN297
+[Devo](Protocols_Details.md#DEVO---7)|AIR/SFC|7|Devo|8CH|10CH|12CH|6CH|7CH|||CYRF6936|
+[DM002](Protocols_Details.md#DM002---33)|AIR|33|||||||||NRF24L01|XN297
+[DSM](Protocols_Details.md#DSM---6)|AIR/SFC|6|DSM2_1F|DSM2_2F|DSMX_1F|DSMX_2F|AUTO|DSMR_1F|DSM2SFC||CYRF6936|
+[DSM_RX](Protocols_Details.md#DSM_RX---70)|AIR/SFC|70|Multi|CPPM|||||||CYRF6936|
+[E010R5](Protocols_Details.md#E010R5---81)|AIR|81|||||||||CYRF6936|RF2500
+[E016H](Protocols_Details.md#E016H---85)||85|||||||||NRF24L01|XN297
+[E016HV2](Protocols_Details.md#E016HV2---80)||80|||||||||CC2500/NRF24L01|unknown
+[E01X](Protocols_Details.md#E01X---45)||45|E012|E015|||||||CYRF6936|HS6200
+[E129](Protocols_Details.md#E129---83)||83|E129|C186|||||||CYRF6936|RF2500
+[EazyRC](Protocols_Details.md#EazyRC---61)||61|||||||||NRF24L01|XN297L
+[ESky](Protocols_Details.md#ESKY---16)||16|ESky|ET4|||||||NRF24L01|
+[ESky150](Protocols_Details.md#ESKY150---35)||35|||||||||NRF24L01|
+[ESky150V2](Protocols_Details.md#ESKY150V2---69)||69|||||||||CC2500|NRF51822
+[Flysky](Protocols_Details.md#FLYSKY---1)||1|Flysky|V9x9|V6x6|V912|CX20||||A7105|
+[Flysky AFHDS2A](Protocols_Details.md#FLYSKY-AFHDS2A---28)||28|PWM_IBUS|PPM_IBUS|PWM_SBUS|PPM_SBUS|Gyro_Off|Gyro_On|Gyro_On_Rev||A7105|
+[Flysky AFHDS2A RX](Protocols_Details.md#FLYSKY-AFHDS2A-RX---56)||56|Multi|CPPM|||||||A7105|
+[FQ777](Protocols_Details.md#FQ777---23)||23|||||||||NRF24L01|SSV7241
+[FrskyD](Protocols_Details.md#FRSKYD---3)||3|D8|Cloned|||||||CC2500|
+[FrskyL](Protocols_Details.md#FRSKYL---67)||67|LR12|LR12 6CH|||||||CC2500|
+[FrskyR9](Protocols_Details.md#FRSKYR9---65)||65|FrskyR9|R9_915|R9_868||||||SX1276|
+[FrskyV](Protocols_Details.md#FRSKYV---25)||25|||||||||CC2500|
+[FrskyX](Protocols_Details.md#FRSKYX---15)||15|CH_16|CH_8|EU_16|EU_8|Cloned|Cloned_8|||CC2500|
+[FrskyX2](Protocols_Details.md#FRSKYX2---64)||64|CH_16|CH_8|EU_16|EU_8|Cloned|Cloned_8|||CC2500|
+[Frsky_RX](Protocols_Details.md#FRSKY_RX---55)||55|Multi|CloneTX|EraseTX|CPPM|||||CC2500|
+[Futaba/SFHSS](Protocols_Details.md#Futaba---21)||21|SFHSS||||||||CC2500|
+[FX](Protocols_Details.md#FX---58)||28|816|620|9630|Q560|QF012||||NRF24L01|
+[FY326](Protocols_Details.md#FY326---20)||20|FY326|FY319|||||||NRF24L01|
+[GD00X](Protocols_Details.md#GD00X---47)||47|GD_V1*|GD_V2*|||||||NRF24L01|XN297L
+[GW008](Protocols_Details.md#GW008---32)||32|||||||||NRF24L01|XN297
+[H36](Protocols_Details.md#H36---103)||H36|||||||||NRF24L01|XN297
+[H8_3D](Protocols_Details.md#H8_3D---36)||36|H8_3D|H20H|H20Mini|H30Mini|||||NRF24L01|XN297
+[Height](Protocols_Details.md#HEIGHT---53)||53|5ch|8ch|||||||A7105|
+[Hisky](Protocols_Details.md#HISKY---4)||4|Hisky|HK310|||||||NRF24L01|
+[Hitec](Protocols_Details.md#HITEC---39)||39|OPT_FW|OPT_HUB|MINIMA||||||CC2500|
+[Hontai](Protocols_Details.md#HONTAI---26)||26|HONTAI|JJRCX1|X5C1|FQ777_951|XKK170||||NRF24L01|XN297
+[HoTT](Protocols_Details.md#HoTT---57)||57|Sync|No_Sync|||||||CC2500|
+[Hubsan](Protocols_Details.md#HUBSAN---2)||2|H107|H301|H501||||||A7105|
+[J6Pro](Protocols_Details.md#J6Pro---22)||22|||||||||CYRF6936|
+[JIABAILE](Protocols_Details.md#JIABAILE---102)||102|Std|Gyro|||||||NRF24L01|XN297
+[JJRC345](Protocols_Details.md#JJRC345---71)||71|JJRC345|SkyTmblr|||||||NRF24L01|XN297
+[JOYSWAY](Protocols_Details.md#JOYSWAY---84)||84|||||||||NRF24L01|XN297
+[KAMTOM](Protocols_Details.md#KAMTOM---104)||104|||||||||NRF24L01|XN297
+[KF606](Protocols_Details.md#KF606---49)||49|KF606|MIG320|ZCZ50||||||NRF24L01|XN297
+[KN](Protocols_Details.md#KN---9)||9|WLTOYS|FEILUN|||||||NRF24L01|
+[Kyosho](Protocols_Details.md#Kyosho---73)||73|FHSS|Hype|||||||A7105|
+[Kyosho2](Protocols_Details.md#Kyosho2---93)||93|KT-17||||||||NRF24L01|
+[Kyosho3](Protocols_Details.md#Kyosho3---98)||98|ASF||||||||CYRF6936|
+[LOLI](Protocols_Details.md#LOLI---82)||82|||||||||NRF24L01|
+[Losi](Protocols_Details.md#Losi---89)||89|||||||||CYRF6936|
+[MJXq](Protocols_Details.md#MJXQ---18)||18|WLH08|X600|X800|H26D|E010*|H26WH|PHOENIX*||NRF24L01|XN297
+[MLINK](Protocols_Details.md#MLINK---78)||78|||||||||CYRF6936|
+[MouldKg](Protocols_Details.md#mouldkg---90)||90|A4444|D4444|A664||||||NRF24L01|XN297
+[MT99xx](Protocols_Details.md#MT99XX---17)||17|MT|H7|YZ|LS|FY805|A180|DRAGON|F949G|NRF24L01|XN297
+[MT99xx2](Protocols_Details.md#MT99XX2---92)||92|PA18|SU35|||||||NRF24L01|XN297
+[NCC1701](Protocols_Details.md#NCC1701---44)||44|||||||||NRF24L01|
+[OMP](Protocols_Details.md#OMP---77)||77|||||||||CC2500&NRF24L01|XN297L
+[OpenLRS](Protocols_Details.md#OpenLRS---27)||27|||||||||None|
+[Pelikan](Protocols_Details.md#Pelikan---60)||60|Pro|Lite|SCX24||||||A7105|
+[Potensic](Protocols_Details.md#Potensic---51)||51|A20||||||||NRF24L01|XN297
+[PROPEL](Protocols_Details.md#PROPEL---66)||66|74-Z||||||||NRF24L01|
+[Q2X2](Protocols_Details.md#Q2X2---29)||29|Q222|Q242|Q282||||||NRF24L01|
+[Q303](Protocols_Details.md#Q303---31)||31|Q303|CX35|CX10D|CX10WD|||||NRF24L01|XN297
+[Q90C](Protocols_Details.md#Q90C---72)||72|Q90C*||||||||NRF24L01|XN297
+[RadioLink](Protocols_Details.md#RadioLink---74)||74|Surface|Air|DumboRC|RC4G|||||CC2500|
+[Realacc](Protocols_Details.md#Realacc---76)||76|R11||||||||NRF24L01|
+[Redpine](Protocols_Details.md#Redpine---50)||50|FAST|SLOW|||||||NRF24L01|XN297
+[Scanner](Protocols_Details.md#Scanner---54)||54|||||||||CC2500|
+[Scorpio](Protocols_Details.md#Scorpio---94)||94|||||||||CYRF6936|
+[SGF22](Protocols_Details.md#SGF22---97)||97|F22|F22S|J20|CX10|||||NRF24L01|XN297
+[Shenqi](Protocols_Details.md#Shenqi---19)||19|Shenqi||||||||NRF24L01|LT8900
+[Shenqi2](Protocols_Details.md#Shenqi2---105)||105|Shenqi2||||||||NRF24L01|XN297
+[Skyartec](Protocols_Details.md#Skyartec---68)||68|||||||||CC2500|CC2500
+[SLT](Protocols_Details.md#SLT---11)||11|SLT_V1|SLT_V2|Q100|Q200|MR100|V1_4CH|RF_SIM||NRF24L01|CC2500
+[SymaX](Protocols_Details.md#Symax---10)||10|SYMAX|SYMAX5C|||||||NRF24L01|
+[Traxxas](Protocols_Details.md#Traxxas---43)||43|TQ2|TQ1|||||||CYRF6936|
+[V2x2](Protocols_Details.md#V2X2---5)||5|V2x2|JXD506|MR101||||||NRF24L01|
+[V761](Protocols_Details.md#V761---48)||48|3CH|4CH|TOPRC||||||NRF24L01|XN297
+[V911S](Protocols_Details.md#V911S---46)||46|V911S*|E119*|||||||NRF24L01|XN297
+[WFLY](Protocols_Details.md#WFLY---40)||40|WFR0x||||||||CYRF6936|
+[WFLY2](Protocols_Details.md#WFLY2---79)||79|RF20x||||||||A7105|
+[WK2x01](Protocols_Details.md#WK2X01---30)||30|WK2801|WK2401|W6_5_1|W6_6_1|W6_HEL|W6_HEL_I|||CYRF6936|
+[WL91X](Protocols_Details.md#WL91X---106)||106|||||||||NRF24L01&CC2500|XN297
+[WPL](Protocols_Details.md#WPL---107)||107|||||||||NRF24L01|XN297
+[XERALL](Protocols_Details.md#XERALL---91)||91|Tank||||||||NRF24L01|XN297
+[XK](Protocols_Details.md#XK---62)||62|X450|X420|Cars||||||NRF24L01&CC2500|XN297
+[XK2](Protocols_Details.md#XK2---99)||99|X4|P10|||||||NRF24L01&CC2500|XN297
+[YD717](Protocols_Details.md#YD717---8)||8|YD717|SKYWLKR|SYMAX4|XINXUN|NIHUI||||NRF24L01|
+[YuXiang](Protocols_Details.md#YuXiang---100)||100|||||||||NRF24L01|XN297
+[ZSX](Protocols_Details.md#ZSX---52)||52|280||||||||NRF24L01|XN297
 * "*" Sub Protocols designated by * suffix are using a XN297L@250kbps which will be emulated by default with the NRF24L01. If option (freq tune) is diffrent from 0, the CC2500 module (if installed) will be used instead. Each specific sub protocol has a more detailed explanation.
 
 # A7105 RF Module
@@ -2238,6 +2239,8 @@ CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12
 ---|---|---|---|---|---|---|---|---|---|---|---
 A|E|T|R|MODE|FLIP|LIGHT|PHOTO|VIDEO|TRIMRESET|BAL|BALHIG
 
+Telemetry is supported. The plane sends a battery status of good->empty which is visible in A1 (good=13.2V->empty=0V) and RSSI gets a dummy value of 100.
+
 ### Sub_protocol F22
 Model: SG F22
 
@@ -2250,12 +2253,19 @@ Manual CH11=-100% & CH12=-100%, Balance CH11=+100% & CH12=-100%, Large Angle Bal
 ### Sub_protocol F22S
 Model: ParkTen F22S
 
-F22S: Mode -100% = 3D, 0% = 6G
+Mode -100% = 3D, 0% = 6G
 
 ### Sub_protocol J20
 Model: KF700 J20
 
-J20: Mode -100% = Gyro off, 0% = Horizontal, 100% = Vertical. CH8 - Invert, CH10 - Fix Height (Altitude hold)
+Mode -100% = Gyro off, 0% = Horizontal, 100% = Vertical. CH8 - Invert, CH10 - Fix Height (Altitude hold)
+
+### Sub_protocol CX10
+Model: Cheerson CX-10 with red PCB
+
+**Only 2 IDs available**, use RX num to cycle through them.
+
+Mode -100% = Low, 0% = Medium, 100% = High
 
 ## Shenqi - *19*
 Autobind protocol
@@ -2361,6 +2371,19 @@ CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9
 ---|---|---|---|---|---|---|---|---
 A|E|T|R|GYRO|CALIB|FLIP|RTN_ACT|RTN
 
+## WPL - *107*
+TX: "Basic", Models: D12 / D12KM / D22 / D32 / D42 / D14
+
+**Only 1 ID** available. If you have a TX contact me on GitHub or RCGroups.
+
+Autobind protocol
+
+CH1|CH2|CH3|CH4|CH5|CH6|CH7
+---|---|---|---|---|---|---
+TH|ST|ST_Trim|Aux|Light|TH_Rate|ST_Rate
+
+Light: -100%=Off, +100%=On, Rate: -100%=Low, +100%=High
+
 ## XERALL - *91*
 Model: Xerall TankCopter