gomaomao/DIY-Multiprotocol-TX-Module
1
0
Fork 0
mirror of https://github.com/pascallanger/DIY-Multiprotocol-TX-Module.git synced 2025-02-04 16:48:10 +00:00
Code Issues Projects Releases Wiki Activity

Update Tx-FlyskyTH9X.md

Browse Source 
Fixed broken link & MarkDown sections.
This commit is contained in:
Sebastien Charpentier 2017-04-19 21:14:41 +02:00 committed by GitHub
parent df347be672
commit f490fa6e7d
1 changed files with 6 additions and 6 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

12
docs/Tx-FlyskyTH9X.md
View File

@ -1,4 +1,4 @@
#Flysky TH9X family of transmitters
# Flysky TH9X family of transmitters
This page is relevant to the following transmitters:
* FlySky TH9X
* Turnigy 9X, Turnigy 9XR
@ -19,21 +19,21 @@ Serial mode is only supported by the er9X firmware. Loading this firmware is be
er9X is very well documented, see [here](http://openrcforums.com/forum/viewtopic.php?f=5&t=6473#p90349)
###Enabling Serial Mode
### Enabling Serial Mode
1. Confirm that the MULTI-Module has the required physical connections between the pins on the back of the Tx and the ATMega328 microprocessor. This may require some soldering and depends on which version of the MULTI-Module you have. Check out your module’s hardware page under the section **Enabling your MULTI-Module for Serial** for details. Click here for the [hardware](Hardware.md) pages.
1. Plug in your DIY Multiprotocol module into the transmitter module bay. If you have a rotary protocol selection switch, turn the switch to position 0 to put the unit into Serial mode.
1. Ensure throttle is down and all switches are in the start position and power up the Tx. The red LED on the DIY Multiprotocol module should be flashing with a period of about 1 second indicating that it has not established a valid serial link with the Tx. This is expected as we have not set up the Tx yet.
1. Create a new model and confirm that the channel order is set to AETR (**This is really important - this is for all protocols - even for DSM as the MULTI-module firware will change the transmitted channel order according to the protocol.**
1. Create a new model and confirm that the channel order is set to AETR (**This is really important - this is for all protocols - even for DSM as the MULTI-module firware will change the transmitted channel order according to the protocol.**
1. In the Model Settings menu scroll down to change the RF settings to MULTI {mikeb - can you write this line }
1. The red LED on the MULTI-Module should briefly flash and then go off. This confirms that the MULTI-Module has established serial communication with the Tx. If the red LED on the module continues to flash at a period of about 1 seconds then it signals that serial communication has not been established. Check your settings under the model menu as described above and check that the protocol selection switch on the module is at 0 (enable Serial mode). If there is still no communication, power down and power up the Tx. Finally check that you have correctly enabled your module for serial as described on the hardware page for your module under the heading "Enabling your module for Serial". Click here to access the [hardware](Hardware.md) and then click on the picture of your module.
###Protocol Selection in Serial mode
### Protocol Selection in Serial mode
To select the protocol:
1. In the Model Setting menu, scroll through the available options under the MULTI option {mikeb to confirm}.
1. Depending on which protocol you have selected you may be required to select a sup-protocol and options. For example, the FrSky protocol has three sub-protocols FrSky_V, FrSky_D and FrSky_X. In some cases the sub-protocols have options that could specify the number of channels, packet frame rate or fine frequency tuning. Check out the [Protocol Details](Protocol_Details.md) page for detailed information and suggestions regarding the sub-protocols and options. The picture below shows the settings in the erSky Model Setup menu for FrSkyX subprotocol with {mike to insert} options:
1. Depending on which protocol you have selected you may be required to select a sup-protocol and options. For example, the FrSky protocol has three sub-protocols FrSky_V, FrSky_D and FrSky_X. In some cases the sub-protocols have options that could specify the number of channels, packet frame rate or fine frequency tuning. Check out the [Protocol Details](../Protocols_Details.md) page for detailed information and suggestions regarding the sub-protocols and options. The picture below shows the settings in the erSky Model Setup menu for FrSkyX subprotocol with {mike to insert} options:
{mikeb to send simple picture}
###Binding in Serial mode
### Binding in Serial mode
1. Switch on the model or put the receiver into bind mode
1. On the transmitter go to the Model Settings menu and scroll down to the [Bind] menu option and press Enter.
1. Press Enter again to exit Bind mode