mirror of
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module.git
synced 2025-03-15 12:59:09 +00:00
Update README.md
This commit is contained in:
parent
6f94409fe1
commit
d26e211b59
41
README.md
41
README.md
@ -19,6 +19,8 @@ The protocol selection is done via a dip switch or a rotary dip switch for acces
|
|||||||
###Using a serial output
|
###Using a serial output
|
||||||
The multiprotocol TX module can be used on a Turnigy 9X, 9XR, 9XR Pro, Taranis, ... running er9x or ersky9X. (A version for OpenTX is being looked at)
|
The multiprotocol TX module can be used on a Turnigy 9X, 9XR, 9XR Pro, Taranis, ... running er9x or ersky9X. (A version for OpenTX is being looked at)
|
||||||
|
|
||||||
|
Using this solution does not need any modification of the TX since it uses the TX module slot PPM pin for serial transfer.
|
||||||
|
|
||||||
Channels order is AETR by default but can be changed in the source code.
|
Channels order is AETR by default but can be changed in the source code.
|
||||||
|
|
||||||
This enables full integration using the radio GUI to setup models with all the available protocols options.
|
This enables full integration using the radio GUI to setup models with all the available protocols options.
|
||||||
@ -34,6 +36,16 @@ Options are:
|
|||||||
- Autobind: Yes or No. At the model selection (or power applied to the TX) a bind sequence will be initiated
|
- Autobind: Yes or No. At the model selection (or power applied to the TX) a bind sequence will be initiated
|
||||||
- Range: test range by setting the transmission power to the lowest value
|
- Range: test range by setting the transmission power to the lowest value
|
||||||
|
|
||||||
|
Note:
|
||||||
|
- there is 2 versions of serial protocol either 8 or 16 channels. 16 channels is the latest version. Make sure to use the right version based on your version of er9x/ersky9x.
|
||||||
|
|
||||||
|
###Telemetry
|
||||||
|
Telemetry is available for er9x and ersky9x TX.
|
||||||
|
There are only 2 protocols so far supporting telemetry: Hubsan and Frsky.
|
||||||
|
|
||||||
|
To enable telemetry on Turnigy 9X or 9XR you need to modify your TX following one of the Frsky mod like this [one](http://blog.oscarliang.net/turnigy-9x-advance-mod/).
|
||||||
|
|
||||||
|
|
||||||
##Protocols
|
##Protocols
|
||||||
|
|
||||||
###TX ID
|
###TX ID
|
||||||
@ -111,6 +123,35 @@ Bayang||NRF24L01
|
|||||||
Note:
|
Note:
|
||||||
- The dial should be set to 0 for serial which means all protocol selection pins should be left unconnected
|
- The dial should be set to 0 for serial which means all protocol selection pins should be left unconnected
|
||||||
|
|
||||||
|
###Protocol channels
|
||||||
|
####SLT
|
||||||
|
All channels -100%..+100%
|
||||||
|
|
||||||
|
CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12|CH13|CH14|CH15|CH16
|
||||||
|
---|---|---|---|---|---|---|---|---|----|----|----|----|----|----|----
|
||||||
|
A|E|T|R|GEAR|PITCH
|
||||||
|
|
||||||
|
####Symax
|
||||||
|
All channels -100%..+100%
|
||||||
|
|
||||||
|
CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12|CH13|CH14|CH15|CH16
|
||||||
|
---|---|---|---|---|---|---|---|---|----|----|----|----|----|----|----
|
||||||
|
A|E|T|R|FLIP||PICTURE|VIDEO|HEADLESS
|
||||||
|
|
||||||
|
####V2X2
|
||||||
|
All channels -100%..+100%
|
||||||
|
|
||||||
|
CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12|CH13|CH14|CH15|CH16
|
||||||
|
---|---|---|---|---|---|---|---|---|----|----|----|----|----|----|----
|
||||||
|
A|E|T|R|FLIP|LIGHT|PICTURE|VIDEO|HEADLESS|MAG_CAL_X|MAG_CAL_Y
|
||||||
|
|
||||||
|
####YD717
|
||||||
|
All channels -100%..+100%
|
||||||
|
|
||||||
|
CH1|CH2|CH3|CH4|CH5|CH6|CH7|CH8|CH9|CH10|CH11|CH12|CH13|CH14|CH15|CH16
|
||||||
|
---|---|---|---|---|---|---|---|---|----|----|----|----|----|----|----
|
||||||
|
A|E|T|R|FLIP|LIGHT|PICTURE|VIDEO|HEADLESS
|
||||||
|
|
||||||
##Hardware
|
##Hardware
|
||||||
|
|
||||||
###RF modules
|
###RF modules
|
||||||
|
Loading…
x
Reference in New Issue
Block a user