diff --git a/Multiprotocol/Multiprotocol.h b/Multiprotocol/Multiprotocol.h
index a3e2614..4c3bc13 100644
--- a/Multiprotocol/Multiprotocol.h
+++ b/Multiprotocol/Multiprotocol.h
@@ -19,7 +19,7 @@
 #define VERSION_MAJOR		1
 #define VERSION_MINOR		2
 #define VERSION_REVISION	1
-#define VERSION_PATCH_LEVEL	81
+#define VERSION_PATCH_LEVEL	82
 
 //******************
 // Protocols
@@ -309,6 +309,7 @@ struct PPM_Parameters
 	uint8_t power : 1;
 	uint8_t autobind : 1;
 	uint8_t option;
+	uint32_t chan_order;
 };
 
 // Telemetry
diff --git a/Multiprotocol/Multiprotocol.ino b/Multiprotocol/Multiprotocol.ino
index 52dbb90..53fa728 100644
--- a/Multiprotocol/Multiprotocol.ino
+++ b/Multiprotocol/Multiprotocol.ino
@@ -147,6 +147,7 @@ uint8_t protocol_flags=0,protocol_flags2=0;
 // PPM variable
 volatile uint16_t PPM_data[NUM_CHN];
 volatile uint8_t  PPM_chan_max=0;
+uint32_t chan_order=0;
 #endif
 
 #if not defined (ORANGE_TX) && not defined (STM32_BOARD)
@@ -435,9 +436,10 @@ void setup()
 		#endif
 		
 		protocol		=	PPM_prot_line->protocol;
-		cur_protocol[1] = protocol;
+		cur_protocol[1] =	protocol;
 		sub_protocol   	=	PPM_prot_line->sub_proto;
 		RX_num			=	PPM_prot_line->rx_num;
+		chan_order		=	PPM_prot_line->chan_order;
 
 		//Forced frequency tuning values for CC2500 protocols
 		#if defined(FORCE_FRSKYD_TUNING) && defined(FRSKYD_CC2500_INO)
@@ -627,6 +629,8 @@ uint8_t Update_All()
 	#ifdef ENABLE_PPM
 		if(mode_select!=MODE_SERIAL && IS_PPM_FLAG_on)		// PPM mode and a full frame has been received
 		{
+			uint32_t chan_or=chan_order;
+			uint8_t ch;
 			for(uint8_t i=0;i<PPM_chan_max;i++)
 			{ // update servo data without interrupts to prevent bad read
 				uint16_t val;
@@ -636,7 +640,17 @@ uint8_t Update_All()
 				val=map16b(val,PPM_MIN_100*2,PPM_MAX_100*2,CHANNEL_MIN_100,CHANNEL_MAX_100);
 				if(val&0x8000) 					val=CHANNEL_MIN_125;
 				else if(val>CHANNEL_MAX_125)	val=CHANNEL_MAX_125;
-				Channel_data[i]=val;
+				if(chan_or)
+				{
+					ch=chan_or>>28;
+					if(ch)
+						Channel_data[ch-1]=val;
+					else
+						Channel_data[i]=val;
+					chan_or<<=4;
+				}
+				else
+					Channel_data[i]=val;
 			}
 			PPM_FLAG_off;									// wait for next frame before update
 			update_channels_aux();
diff --git a/Multiprotocol/_Config.h b/Multiprotocol/_Config.h
index 226738d..b7c5070 100644
--- a/Multiprotocol/_Config.h
+++ b/Multiprotocol/_Config.h
@@ -364,99 +364,99 @@
 // short press the bind button multiple times until you reach the desired one. The bank number currently selected is indicated by the number of LED flash.
 // Full procedure is located here: https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md#protocol-selection-in-ppm-mode
 
-//The parameter below indicates the number of desired banks between 1 and 5. Default is 5.
-#define NBR_BANKS 5
+//The parameter below indicates the number of desired banks between 1 and 5. Default is 1.
+#define NBR_BANKS 1
 
 const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 #if NBR_BANKS > 0
 //******************************       BANK 1       ******************************
-//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option
-/*	1	*/	{PROTO_FLYSKY,	Flysky		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	2	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 0
-/*	3	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	1	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 1
-/*	4	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	2	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 2
-/*	5	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	3	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 3
-/*	6	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	2	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 4
-/*	7	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	3	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 5
-/*	8	*/	{PROTO_SFHSS,	H107		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	9	*/	{PROTO_FRSKYV,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40		},	// option=fine freq tuning
-/*	10	*/	{PROTO_FRSKYD,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40		},	// option=fine freq tuning
-/*	11	*/	{PROTO_FRSKYX,	CH_16		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40		},	// option=fine freq tuning
-/*	12	*/	{PROTO_FRSKYX,	EU_16		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40		},	// option=fine freq tuning
-/*	13	*/	{PROTO_DEVO	,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	14	*/	{PROTO_WK2x01,	WK2801		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
+//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option	Chan Order
+/*	1	*/	{PROTO_FLYSKY,	Flysky		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	2	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 0
+/*	3	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	1	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 1
+/*	4	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	2	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 2
+/*	5	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	3	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 3
+/*	6	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	2	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 4
+/*	7	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	3	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 5
+/*	8	*/	{PROTO_SFHSS,	H107		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	9	*/	{PROTO_FRSKYV,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40	,	0x00000000 },	// option=fine freq tuning
+/*	10	*/	{PROTO_FRSKYD,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40	,	0x00000000 },	// option=fine freq tuning
+/*	11	*/	{PROTO_FRSKYX,	CH_16		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40	,	0x00000000 },	// option=fine freq tuning
+/*	12	*/	{PROTO_FRSKYX,	EU_16		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40	,	0x00000000 },	// option=fine freq tuning
+/*	13	*/	{PROTO_DEVO	,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	14	*/	{PROTO_WK2x01,	WK2801		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
 #endif
 #if NBR_BANKS > 1
 //******************************       BANK 2       ******************************
-//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option
-/*	1	*/	{PROTO_DSM	,	DSM2_11		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6		},	// option=number of channels
-/*	2	*/	{PROTO_DSM	,	DSM2_22		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6		},	// option=number of channels
-/*	3	*/	{PROTO_DSM	,	DSMX_11		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6		},	// option=number of channels
-/*	4	*/	{PROTO_DSM	,	DSMX_22		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6		},	// option=number of channels
-/*	5	*/	{PROTO_DSM	,	DSM2_11		,	0	,	P_HIGH	,	NO_AUTOBIND	,	8		},	// option=number of channels
-/*	6	*/	{PROTO_DSM	,	DSM2_22		,	0	,	P_HIGH	,	NO_AUTOBIND	,	8		},	// option=number of channels
-/*	7	*/	{PROTO_DSM	,	DSMX_11		,	0	,	P_HIGH	,	NO_AUTOBIND	,	8		},	// option=number of channels
-/*	8	*/	{PROTO_DSM	,	DSMX_22		,	0	,	P_HIGH	,	NO_AUTOBIND	,	8		},	// option=number of channels
-/*	9	*/	{PROTO_SLT	,	SLT_V1		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6		},
-/*	10	*/	{PROTO_HUBSAN,	H107		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	11	*/	{PROTO_HUBSAN,	H301		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	12	*/	{PROTO_HUBSAN,	H501		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	13	*/	{PROTO_HISKY,	Hisky		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	14	*/	{PROTO_V2X2	,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
+//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option	Chan Order
+/*	1	*/	{PROTO_DSM	,	DSM2_11		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6	,	0x00000000 },	// option=number of channels
+/*	2	*/	{PROTO_DSM	,	DSM2_22		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6	,	0x00000000 },	// option=number of channels
+/*	3	*/	{PROTO_DSM	,	DSMX_11		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6	,	0x00000000 },	// option=number of channels
+/*	4	*/	{PROTO_DSM	,	DSMX_22		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6	,	0x00000000 },	// option=number of channels
+/*	5	*/	{PROTO_DSM	,	DSM2_11		,	0	,	P_HIGH	,	NO_AUTOBIND	,	8	,	0x00000000 },	// option=number of channels
+/*	6	*/	{PROTO_DSM	,	DSM2_22		,	0	,	P_HIGH	,	NO_AUTOBIND	,	8	,	0x00000000 },	// option=number of channels
+/*	7	*/	{PROTO_DSM	,	DSMX_11		,	0	,	P_HIGH	,	NO_AUTOBIND	,	8	,	0x00000000 },	// option=number of channels
+/*	8	*/	{PROTO_DSM	,	DSMX_22		,	0	,	P_HIGH	,	NO_AUTOBIND	,	8	,	0x00000000 },	// option=number of channels
+/*	9	*/	{PROTO_SLT	,	SLT_V1		,	0	,	P_HIGH	,	NO_AUTOBIND	,	6	,	0x00000000 },
+/*	10	*/	{PROTO_HUBSAN,	H107		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	11	*/	{PROTO_HUBSAN,	H301		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	12	*/	{PROTO_HUBSAN,	H501		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	13	*/	{PROTO_HISKY,	Hisky		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	14	*/	{PROTO_V2X2	,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
 #endif
 #if NBR_BANKS > 2
 //******************************       BANK 3       ******************************
-//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option
-/*	1	*/	{PROTO_ESKY	,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	2	*/	{PROTO_ESKY150,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	3	*/	{PROTO_ASSAN,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	4	*/	{PROTO_CORONA,	COR_V2		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	5	*/	{PROTO_SYMAX,	SYMAX		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	6	*/	{PROTO_KN	,	WLTOYS		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	7	*/	{PROTO_BAYANG,	BAYANG		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	8	*/	{PROTO_BAYANG,	H8S3D		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	9	*/	{PROTO_BAYANG,	X16_AH		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	10	*/	{PROTO_BAYANG,	IRDRONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	11	*/	{PROTO_H8_3D,	H8_3D		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	12	*/	{PROTO_H8_3D,	H20H		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	13	*/	{PROTO_H8_3D,	H20MINI		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	14	*/	{PROTO_H8_3D,	H30MINI		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
+//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option	Chan Order
+/*	1	*/	{PROTO_ESKY	,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	2	*/	{PROTO_ESKY150,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	3	*/	{PROTO_ASSAN,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	4	*/	{PROTO_CORONA,	COR_V2		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	5	*/	{PROTO_SYMAX,	SYMAX		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	6	*/	{PROTO_KN	,	WLTOYS		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	7	*/	{PROTO_BAYANG,	BAYANG		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	8	*/	{PROTO_BAYANG,	H8S3D		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	9	*/	{PROTO_BAYANG,	X16_AH		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	10	*/	{PROTO_BAYANG,	IRDRONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	11	*/	{PROTO_H8_3D,	H8_3D		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	12	*/	{PROTO_H8_3D,	H20H		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	13	*/	{PROTO_H8_3D,	H20MINI		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	14	*/	{PROTO_H8_3D,	H30MINI		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
 #endif
 #if NBR_BANKS > 3
 //******************************       BANK 4       ******************************
-//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option
-/*	1	*/	{PROTO_MJXQ	,	WLH08		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	2	*/	{PROTO_MJXQ	,	X600		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	3	*/	{PROTO_MJXQ	,	X800		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	4	*/	{PROTO_MJXQ	,	H26D		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	5	*/	{PROTO_MJXQ	,	E010		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	6	*/	{PROTO_MJXQ	,	H26WH		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	7	*/	{PROTO_HONTAI,	HONTAI		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	8	*/	{PROTO_HONTAI,	JJRCX1		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	9	*/	{PROTO_HONTAI,	X5C1		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	10	*/	{PROTO_HONTAI,	FQ777_951	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	11	*/	{PROTO_Q303	,	Q303		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	12	*/	{PROTO_Q303	,	CX35		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	13	*/	{PROTO_Q303	,	CX10D		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	14	*/	{PROTO_Q303	,	CX10WD		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
+//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option	Chan Order
+/*	1	*/	{PROTO_MJXQ	,	WLH08		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	2	*/	{PROTO_MJXQ	,	X600		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	3	*/	{PROTO_MJXQ	,	X800		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	4	*/	{PROTO_MJXQ	,	H26D		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	5	*/	{PROTO_MJXQ	,	E010		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	6	*/	{PROTO_MJXQ	,	H26WH		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	7	*/	{PROTO_HONTAI,	HONTAI		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	8	*/	{PROTO_HONTAI,	JJRCX1		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	9	*/	{PROTO_HONTAI,	X5C1		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	10	*/	{PROTO_HONTAI,	FQ777_951	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	11	*/	{PROTO_Q303	,	Q303		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	12	*/	{PROTO_Q303	,	CX35		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	13	*/	{PROTO_Q303	,	CX10D		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	14	*/	{PROTO_Q303	,	CX10WD		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
 #endif
 #if NBR_BANKS > 4
 //******************************       BANK 5       ******************************
-//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option
-/*	1	*/	{PROTO_CX10	,	CX10_GREEN	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	2	*/	{PROTO_CX10	,	CX10_BLUE	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	3	*/	{PROTO_CX10	,	DM007		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	4	*/	{PROTO_CX10	,	JC3015_1	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	5	*/	{PROTO_CX10	,	JC3015_2	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	6	*/	{PROTO_CX10	,	MK33041		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	7	*/	{PROTO_Q2X2	,	Q222		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	8	*/	{PROTO_Q2X2	,	Q242		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	9	*/	{PROTO_Q2X2	,	Q282		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	10	*/	{PROTO_CG023,	CG023		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	11	*/	{PROTO_CG023,	YD829		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	12	*/	{PROTO_FQ777,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	13	*/	{PROTO_YD717,	YD717		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	14	*/	{PROTO_MT99XX,	MT99		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
+//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option	Chan Order
+/*	1	*/	{PROTO_CX10	,	CX10_GREEN	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	2	*/	{PROTO_CX10	,	CX10_BLUE	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	3	*/	{PROTO_CX10	,	DM007		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	4	*/	{PROTO_CX10	,	JC3015_1	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	5	*/	{PROTO_CX10	,	JC3015_2	,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	6	*/	{PROTO_CX10	,	MK33041		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	7	*/	{PROTO_Q2X2	,	Q222		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	8	*/	{PROTO_Q2X2	,	Q242		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	9	*/	{PROTO_Q2X2	,	Q282		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	10	*/	{PROTO_CG023,	CG023		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	11	*/	{PROTO_CG023,	YD829		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	12	*/	{PROTO_FQ777,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	13	*/	{PROTO_YD717,	YD717		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	14	*/	{PROTO_MT99XX,	MT99		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
 #endif
 };
 // RX_Num is used for TX & RX match. Using different RX_Num values for each receiver will prevent starting a model with the false config loaded...
@@ -473,6 +473,15 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]=	{
 // Option: the value is between -128 and +127.
 // The option value is only valid for some protocols, read this page for more information: https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md
 
+// Chan order: if the value is different from 0, this setting will remap the first 8 channels in any given order before giving them to the protocol.
+// It does not disable the automatic channel remapping of the protocol itself but changes the input of it.
+// Even if your TX is sending less than 8 channels you have to respect the format like if it was.
+// Examples:
+//  - 0x12345678 will give to the protocol the channels in the order 1,2,3,4,5,6,7,8 which is equivalent to 0x00000000.
+//  - 0x42315678 will give to the protocol the channels in the order 4,2,3,1,5,6,7,8 swapping channel 1 and 4.
+//  - 0x40010000 will give to the protocol the channels in the order 4,2,3,1,5,6,7,8 swapping channel 1 and 4. Note: 0 means leave the channel where it is.
+//  - 0x0000ABCD will give to the protocol the channels in the order 1,2,3,4,10,11,12,13 which potentially enables acces to channels not available on your TX. Note A=10,B=11,C=12,D=13,E=14,F=15.
+
 /* Available protocols and associated sub protocols to pick and choose from (Listed in alphabetical order)
 	PROTO_AFHDS2A
 		PWM_IBUS
diff --git a/Multiprotocol/_MyConfig.h.example b/Multiprotocol/_MyConfig.h.example
index b324ad9..677896f 100644
--- a/Multiprotocol/_MyConfig.h.example
+++ b/Multiprotocol/_MyConfig.h.example
@@ -60,20 +60,20 @@
 	#define MY_PPM_PROT		// Use the bellow protocol list
 	const PPM_Parameters My_PPM_prot[14*NBR_BANKS]={
 //******************************       BANK 1       ******************************
-//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option
-/*	1	*/	{PROTO_KN	,	WLTOYS		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	2	*/	{PROTO_FLYSKY,	Flysky		,	0	,	P_HIGH	,	AUTOBIND	,	0		},
-/*	3	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	1	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 1
-/*	4	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	2	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 2
-/*	5	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	3	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 3
-/*	6	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	2	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 4
-/*	7	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	3	,	P_HIGH	,	NO_AUTOBIND	,	0		},	// RX number 5
-/*	8	*/	{PROTO_SFHSS,	H107		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	9	*/	{PROTO_FRSKYV,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40		},	// option=fine freq tuning
-/*	10	*/	{PROTO_FRSKYD,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40		},	// option=fine freq tuning
-/*	11	*/	{PROTO_FRSKYX,	CH_16		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40		},	// option=fine freq tuning
-/*	12	*/	{PROTO_FRSKYX,	EU_16		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40		},	// option=fine freq tuning
-/*	13	*/	{PROTO_DEVO	,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
-/*	14	*/	{PROTO_WK2x01,	WK2801		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0		},
+//	Switch	Protocol 		Sub protocol	RX_Num	Power		Auto Bind		Option	Chan Order
+/*	1	*/	{PROTO_KN	,	WLTOYS		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	2	*/	{PROTO_FLYSKY,	Flysky		,	0	,	P_HIGH	,	AUTOBIND	,	0	,	0x00000000 },
+/*	3	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	1	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 1
+/*	4	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	2	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 2
+/*	5	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	3	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 3
+/*	6	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	2	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 4
+/*	7	*/	{PROTO_AFHDS2A,	PWM_IBUS	,	3	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },	// RX number 5
+/*	8	*/	{PROTO_SFHSS,	H107		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	9	*/	{PROTO_FRSKYV,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40	,	0x00000000 },	// option=fine freq tuning
+/*	10	*/	{PROTO_FRSKYD,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40	,	0x00000000 },	// option=fine freq tuning
+/*	11	*/	{PROTO_FRSKYX,	CH_16		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40	,	0x00000000 },	// option=fine freq tuning
+/*	12	*/	{PROTO_FRSKYX,	EU_16		,	0	,	P_HIGH	,	NO_AUTOBIND	,	40	,	0x00000000 },	// option=fine freq tuning
+/*	13	*/	{PROTO_DEVO	,	NONE		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
+/*	14	*/	{PROTO_WK2x01,	WK2801		,	0	,	P_HIGH	,	NO_AUTOBIND	,	0	,	0x00000000 },
 	};
 #endif