gomaomao/DIY-Multiprotocol-TX-Module
1
0
Fork 0
mirror of https://github.com/pascallanger/DIY-Multiprotocol-TX-Module.git synced 2025-07-01 18:27:53 +00:00
Code Issues Projects Releases Wiki Activity

Typos...

Browse Source
This commit is contained in:
pascallanger 2016-10-18 09:27:14 +02:00
parent b9f297935b
commit 68648b9920
2 changed files with 5 additions and 5 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

2
Multiprotocol/Validate.h
View File

@ -5,7 +5,7 @@
#if not defined (ORANGE_TX) && not defined (STM32_BOARD)
//Atmega328p
#if not defined(ARDUINO_AVR_PRO) && not defined(ARDUINO_AVR_MINI) && not defined(ARDUINO_AVR_NANO)
#error You must select the board type "Arduino Pro or Pro Mini" or "Arduino Mini"
#error You must select one of these boards: "Multi 4-in-1", "Arduino Pro or Pro Mini" or "Arduino Mini"
#endif
#if F_CPU != 16000000L || not defined(__AVR_ATmega328P__)
#error You must select the processor type "ATmega328(5V, 16MHz)"

8
Multiprotocol/_Config.h
View File

@ -51,7 +51,7 @@
/*** PROTOCOLS TO INCLUDE ***/
/****************************/
//In this section select the protocols you want to be accessible when using the module.
//All the protocols will not fit in the module so you need to pick and choose.
//All the protocols will not fit in the Atmega328p module so you need to pick and choose.
//Comment the protocols you are not using with "//" to save Flash space.
//The protocols below need an A7105 to be installed
@ -137,9 +137,9 @@
//#define TX_CUSTOM //Custom
// The lines below are used to set the end points in microseconds (µs) if you have selected TX_CUSTOM.
// A few things to considered:
// A few things to consider:
// - If you put too big values compared to your TX you won't be able to reach the extremes which is bad for throttle as an example
// - If you put too low values you won't be able to use your full stick range, it will be maxed out before reaching the end
// - If you put too low values you won't be able to use your full stick range, it will be maxed out before reaching the ends
// - Centered stick value is usually 1500. It should match the middle between MIN and MAX, ie Center=(MAX-MIN)/2+MIN. If your TX is not centered you can adjust the value MIN or MAX.
// - 100% is the value when the model is by default, 125% is the value when you extend the servo travel which is only used by some protocols
#if defined(TX_CUSTOM)
@ -265,7 +265,7 @@ const PPM_Parameters PPM_prot[15]= {
// Auto Bind AUTOBIND or NO_AUTOBIND
// For protocols which does not require binding at each power up (like Flysky, FrSky...), you might still want a bind to be initiated each time you power up the TX.
// As an exxample, it's usefull for the WLTOYS F929/F939/F949/F959 (all using the Flysky protocol) which requires a bind at each power up.
// As an example, it's usefull for the WLTOYS F929/F939/F949/F959 (all using the Flysky protocol) which requires a bind at each power up.
// Option: the value is between -127 and +127.
// The option value is only valid for some protocols, read this page for more information: https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md