diff --git a/Multiprotocol/IKEA_Ansluta_cc2500.ino b/Multiprotocol/IKEA_Ansluta_cc2500.ino
new file mode 100644
index 0000000..0539433
--- /dev/null
+++ b/Multiprotocol/IKEA_Ansluta_cc2500.ino
@@ -0,0 +1,122 @@
+/*
+ This project is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ Multiprotocol is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with Multiprotocol. If not, see .
+ */
+// This module makes it possible to bind to and control the IKEA "Ansluta" line
+// of remote-controlled lights.
+// To bind, first switch the receiver into binding mode, then the TX.
+// Once bound, the TX can send one of three commands:
+// lights off, lights dimmed 50% and lights on.
+// Those are mapped to throttle ranges 0..0x55, 0x56..0xAA, 0xAB..0xFF.
+#if defined(IKEAANSLUTA_CC2500_INO)
+
+#include "iface_cc2500.h"
+
+#define IKEAANSLUTA_BIND_COUNT 30 // ~ 2sec autobind/65ms per loop = 30 binding packets
+
+// Commands
+#define IKEAANSLUTA_LIGHT_OFF 0x01
+#define IKEAANSLUTA_LIGHT_DIM 0x02 // 50% dimmed light
+#define IKEAANSLUTA_LIGHT_ON 0x03
+#define IKEAANSLUTA_PAIR 0xFF
+
+void IKEAANSLUTA_send_command(uint8_t command){
+ CC2500_Strobe(CC2500_SIDLE);
+ packet[4] = option;
+ packet[5] = command;
+ CC2500_WriteData(packet, 8);
+}
+
+uint16_t IKEAANSLUTA_callback(void)
+{
+ if (bind_counter) {
+ IKEAANSLUTA_send_command(IKEAANSLUTA_PAIR);
+ if(--bind_counter == 0) {
+ BIND_DONE;
+ CC2500_SetPower();
+ }
+ }
+ else {
+ uint8_t throttle = convert_channel_8b(THROTTLE);
+ uint8_t cmd = throttle <= 0x55 ? IKEAANSLUTA_LIGHT_OFF :
+ throttle <= 0xAA ? IKEAANSLUTA_LIGHT_DIM :
+ IKEAANSLUTA_LIGHT_ON;
+ IKEAANSLUTA_send_command(cmd);
+ }
+ return 65535; // 65ms loop cycle is more than enough here (we could make it even longer if not for uint16_t)
+}
+
+// Register initialization values as a continuous memory block (to save on flash memory)
+const PROGMEM uint8_t IKEAANSLUTA_init_values[] = {
+ 0xFF, // CC2500_06_PKTLEN
+ 0x04, // CC2500_07_PKTCTRL1
+ 0x05, // CC2500_08_PKTCTRL0
+ 0x00, // CC2500_09_ADDR (unused, default)
+ 0x10, // CC2500_0A_CHANNR
+ 0x09, // CC2500_0B_FSCTRL1
+ 0x00, // CC2500_0C_FSCTRL0
+ 0x5D, // CC2500_0D_FREQ2
+ 0x93, // CC2500_0E_FREQ1
+ 0xB1, // CC2500_0F_FREQ0
+ 0x2D, // CC2500_10_MDMCFG4
+ 0x3B, // CC2500_11_MDMCFG3
+ 0x73, // CC2500_12_MDMCFG2
+ 0xA2, // CC2500_13_MDMCFG1
+ 0xF8, // CC2500_14_MDMCFG0
+ 0x01, // CC2500_15_DEVIATN
+ 0x07, // CC2500_16_MCSM2
+ 0x30, // CC2500_17_MCSM1
+ 0x18, // CC2500_18_MCSM0
+ 0x1D, // CC2500_19_FOCCFG
+ 0x1C, // CC2500_1A_BSCFG
+ 0xC7, // CC2500_1B_AGCCTRL2
+ 0x00, // CC2500_1C_AGCCTRL1
+ 0xB2, // CC2500_1D_AGCCTRL0
+ 0x87, // CC2500_1E_WOREVT1 (unused, default)
+ 0x6b, // CC2500_1F_WOREVT0 (unused, default)
+ 0xf8, // CC2500_20_WORCTRL (unused, default)
+ 0xB6, // CC2500_21_FREND1
+ 0x10, // CC2500_22_FREND0
+ 0xEA, // CC2500_23_FSCAL3
+ 0x0A, // CC2500_24_FSCAL2
+ 0x00, // CC2500_25_FSCAL1
+ 0x11, // CC2500_26_FSCAL0
+ 0x41, // CC2500_27_RCCTRL1
+ 0x00, // CC2500_28_RCCTRL0
+};
+
+void IKEAANSLUTA_init(void)
+{
+ if (IS_BIND_DONE) bind_counter = 0;
+ else bind_counter = IKEAANSLUTA_BIND_COUNT;
+
+ // All packets we send are the same
+ packet[0] = 0x06;
+ packet[1] = 0x55;
+ packet[2] = 0x01;
+ // Bytes 3&4 are the transmitter address (to which the RX binds)
+ // Byte 5 is the command.
+ packet[3] = rx_tx_addr[3]; // +
+ // packet[4] = option;
+ // packet[5] = 0x00; // Command goes here
+ packet[6] = 0xAA;
+ packet[7] = 0xFF;
+
+ // Configure & initialize CC2500
+ for (uint8_t i = 0; i <= CC2500_28_RCCTRL0-CC2500_06_PKTLEN; ++i)
+ CC2500_WriteReg(CC2500_06_PKTLEN+i, pgm_read_byte_near(&IKEAANSLUTA_init_values[i]));
+ CC2500_SetTxRxMode(TX_EN);
+ CC2500_SetPower();
+}
+
+#endif
diff --git a/Multiprotocol/Multi_Protos.ino b/Multiprotocol/Multi_Protos.ino
index 6930394..ff85c1c 100644
--- a/Multiprotocol/Multi_Protos.ino
+++ b/Multiprotocol/Multi_Protos.ino
@@ -98,6 +98,7 @@ const char STR_E010R5[] ="E010r5";
const char STR_LOLI[] ="LOLI";
const char STR_E129[] ="E129";
const char STR_E016H[] ="E016H";
+const char STR_IKEAANSLUTA[]="Ansluta";
const char STR_CONFIG[] ="Config";
const char STR_SUBTYPE_FLYSKY[] = "\x04""Std\0""V9x9""V6x6""V912""CX20";
@@ -330,6 +331,9 @@ const mm_protocol_definition multi_protocols[] = {
#if defined(HUBSAN_A7105_INO)
{PROTO_HUBSAN, STR_HUBSAN, STR_SUBTYPE_HUBSAN, 3, OPTION_VIDFREQ, 0, 0, SW_A7105, HUBSAN_init, HUBSAN_callback },
#endif
+ #if defined(IKEAANSLUTA_CC2500_INO)
+ {PROTO_IKEAANSLUTA,STR_IKEAANSLUTA,NO_SUBTYPE, 0, OPTION_OPTION, 0, 0, SW_CC2500, IKEAANSLUTA_init,IKEAANSLUTA_callback },
+ #endif
#if defined(J6PRO_CYRF6936_INO)
{PROTO_J6PRO, STR_J6PRO, NO_SUBTYPE, 0, OPTION_NONE, 0, 1, SW_CYRF, J6PRO_init, J6PRO_callback },
#endif
diff --git a/Multiprotocol/Multiprotocol.h b/Multiprotocol/Multiprotocol.h
index 4a08ad5..3a57c6f 100644
--- a/Multiprotocol/Multiprotocol.h
+++ b/Multiprotocol/Multiprotocol.h
@@ -19,7 +19,7 @@
#define VERSION_MAJOR 1
#define VERSION_MINOR 3
#define VERSION_REVISION 2
-#define VERSION_PATCH_LEVEL 78
+#define VERSION_PATCH_LEVEL 79
#define MODE_SERIAL 0
@@ -113,7 +113,8 @@ enum PROTOCOLS
PROTO_E129 = 83, // =>CYRF6936
PROTO_JOYSWAY = 84, // =>A7105
PROTO_E016H = 85, // =>NRF24L01
- PROTO_CONFIG = 86, // Module config
+ PROTO_IKEAANSLUTA = 86, // =>CC2500
+ PROTO_CONFIG = 87, // Module config
PROTO_NANORF = 126, // =>NRF24L01
PROTO_TEST = 127, // =>CC2500
diff --git a/Multiprotocol/_Config.h b/Multiprotocol/_Config.h
index 1243b23..e98a3ac 100644
--- a/Multiprotocol/_Config.h
+++ b/Multiprotocol/_Config.h
@@ -203,6 +203,7 @@
#define FRSKY_RX_CC2500_INO
#define HITEC_CC2500_INO
#define HOTT_CC2500_INO
+//#define IKEAANSLUTA_CC2500_INO // This is mostly a "for-fun" kind of a thing, not needed for most users
#define SCANNER_CC2500_INO
#define FUTABA_CC2500_INO
#define SKYARTEC_CC2500_INO
@@ -693,6 +694,7 @@ const PPM_Parameters PPM_prot[14*NBR_BANKS]= {
H107
H301
H501
+ PROTO_IKEAANSLUTA
PROTO_J6PRO
NONE
PROTO_JJRC345