mirror of
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module.git
synced 2025-02-04 18:48:11 +00:00
_Config.h file and all protocol settings for PPM mode
This commit is contained in:
pascallanger
parent
3fcaf93788
commit
151e82a2c3
@ -151,7 +151,7 @@ static void frsky2way_init(uint8_t bind)
|
||||
cc2500_writeReg(CC2500_08_PKTCTRL0, 0x05);
|
||||
cc2500_writeReg(CC2500_3E_PATABLE, 0xff);
|
||||
cc2500_writeReg(CC2500_0B_FSCTRL1, 0x08);
|
||||
cc2500_writeReg(CC2500_0C_FSCTRL0, fine);
|
||||
cc2500_writeReg(CC2500_0C_FSCTRL0, option);
|
||||
//base freq FREQ = 0x5C7627 (F = 2404MHz)
|
||||
cc2500_writeReg(CC2500_0D_FREQ2, 0x5c);
|
||||
cc2500_writeReg(CC2500_0E_FREQ1, 0x76);
|
||||
|
||||
@ -18,21 +18,21 @@
|
||||
|
||||
#include "iface_nrf24l01.h"
|
||||
|
||||
#define BIND_COUNT 1000
|
||||
#define TXID_SIZE 5
|
||||
#define FREQUENCE_NUM 20
|
||||
#define HISKY_BIND_COUNT 1000
|
||||
#define HISKY_TXID_SIZE 5
|
||||
#define HISKY_FREQUENCE_NUM 20
|
||||
//
|
||||
uint8_t bind_buf_arry[4][10];
|
||||
|
||||
// HiSky protocol uses TX id as an address for nRF24L01, and uses frequency hopping sequence
|
||||
// which does not depend on this id and is passed explicitly in binding sequence. So we are free
|
||||
// to generate this sequence as we wish. It should be in the range [02..77]
|
||||
static void calc_fh_channels(uint32_t seed)
|
||||
static void calc_fh_channels()
|
||||
{
|
||||
uint8_t idx = 0;
|
||||
uint32_t rnd = seed;
|
||||
uint32_t rnd = MProtocol_id;
|
||||
|
||||
while (idx < FREQUENCE_NUM)
|
||||
while (idx < HISKY_FREQUENCE_NUM)
|
||||
{
|
||||
uint8_t i;
|
||||
uint8_t count_2_26 = 0, count_27_50 = 0, count_51_74 = 0;
|
||||
@ -41,7 +41,7 @@ static void calc_fh_channels(uint32_t seed)
|
||||
// Use least-significant byte. 73 is prime, so channels 76..77 are unused
|
||||
uint8_t next_ch = ((rnd >> 8) % 73) + 2;
|
||||
// Keep the distance 2 between the channels - either odd or even
|
||||
if (((next_ch ^ (uint8_t)seed) & 0x01 )== 0)
|
||||
if (((next_ch ^ (uint8_t)rx_tx_addr[3]) & 0x01 )== 0)
|
||||
continue;
|
||||
// Check that it's not duplicated and spread uniformly
|
||||
for (i = 0; i < idx; i++) {
|
||||
@ -195,7 +195,7 @@ uint16_t hisky_cb()
|
||||
NRF24L01_WriteRegisterMulti(NRF24L01_10_TX_ADDR, rx_tx_addr, 5);
|
||||
NRF24L01_WriteReg(NRF24L01_05_RF_CH, hopping_frequency[hopping_frequency_no]);
|
||||
hopping_frequency_no++;
|
||||
if (hopping_frequency_no >= FREQUENCE_NUM)
|
||||
if (hopping_frequency_no >= HISKY_FREQUENCE_NUM)
|
||||
hopping_frequency_no = 0;
|
||||
break;
|
||||
case 7:
|
||||
@ -213,15 +213,19 @@ uint16_t hisky_cb()
|
||||
return 1000; // send 1 binding packet and 1 data packet per 9ms
|
||||
}
|
||||
|
||||
// Generate internal id from TX id and manufacturer id (STM32 unique id)
|
||||
static void initialize_tx_id()
|
||||
{
|
||||
//Generate frequency hopping table
|
||||
if(sub_protocol==HK310)
|
||||
for(uint8_t i=0;i<FREQUENCE_NUM;i++)
|
||||
hopping_frequency[i]=i; // Sequential order hop channels...
|
||||
{
|
||||
// for HiSky surface protocol, the transmitter always generates hop channels in sequential order.
|
||||
// The transmitter only generates the first hop channel between 0 and 49. So the channel range is from 0 to 69.
|
||||
hopping_frequency_no=rx_tx_addr[0]%50;
|
||||
for(uint8_t i=0;i<HISKY_FREQUENCE_NUM;i++)
|
||||
hopping_frequency[i]=hopping_frequency_no++; // Sequential order hop channels...
|
||||
}
|
||||
else
|
||||
calc_fh_channels(MProtocol_id);
|
||||
calc_fh_channels();
|
||||
}
|
||||
|
||||
uint16_t initHiSky()
|
||||
@ -234,7 +238,7 @@ uint16_t initHiSky()
|
||||
binding_idx = 0;
|
||||
|
||||
if(IS_AUTOBIND_FLAG_on)
|
||||
bind_counter = BIND_COUNT;
|
||||
bind_counter = HISKY_BIND_COUNT;
|
||||
else
|
||||
bind_counter = 0;
|
||||
return 1000;
|
||||
|
||||
@ -12,6 +12,7 @@
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with Multiprotocol. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
// compatible with Hubsan H102D, H107/L/C/D and H107P/C+/D+
|
||||
// Last sync with hexfet new_protocols/hubsan_a7105.c dated 2015-12-11
|
||||
|
||||
#if defined(HUBSAN_A7105_INO)
|
||||
|
||||
@ -4,7 +4,7 @@
|
||||
http://www.rcgroups.com/forums/showthread.php?t=2165676
|
||||
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/edit/master/README.md
|
||||
|
||||
Thanks to PhracturedBlue
|
||||
Thanks to PhracturedBlue, Hexfet, Goebish and all protocol developers
|
||||
Ported from deviation firmware
|
||||
|
||||
This project is free software: you can redistribute it and/or modify
|
||||
@ -23,71 +23,10 @@
|
||||
#include <avr/eeprom.h>
|
||||
#include <avr/pgmspace.h>
|
||||
#include <util/delay.h>
|
||||
#include "Multiprotocol.h"
|
||||
|
||||
//******************************************************
|
||||
//******************************************************
|
||||
// Multiprotocol module configuration starts here
|
||||
|
||||
//Uncomment the type of TX
|
||||
#define TX_ER9X //ER9X AETR (988<->2012µs)
|
||||
//#define TX_DEVO7 //DEVO7 EATR (1120<->1920µs)
|
||||
//#define TX_SPEKTRUM //Spektrum TAER (1100<->1900µs)
|
||||
//#define TX_HISKY //HISKY AETR (1100<->1900µs)
|
||||
|
||||
#include "multiprotocol.h"
|
||||
|
||||
//Uncomment to enable 8 channels serial protocol, 16 otherwise
|
||||
//#define NUM_SERIAL_CH_8
|
||||
|
||||
//Uncomment to enable telemetry
|
||||
#define TELEMETRY
|
||||
|
||||
//Comment protocols to exclude from compilation
|
||||
#define BAYANG_NRF24L01_INO
|
||||
#define CG023_NRF24L01_INO
|
||||
#define CX10_NRF24L01_INO
|
||||
#define DEVO_CYRF6936_INO
|
||||
#define DSM2_CYRF6936_INO
|
||||
#define ESKY_NRF24L01_INO
|
||||
#define FLYSKY_A7105_INO
|
||||
#define FRSKY_CC2500_INO
|
||||
#define HISKY_NRF24L01_INO
|
||||
#define HUBSAN_A7105_INO
|
||||
#define KN_NRF24L01_INO
|
||||
#define SLT_NRF24L01_INO
|
||||
#define SYMAX_NRF24L01_INO
|
||||
#define V2X2_NRF24L01_INO
|
||||
#define YD717_NRF24L01_INO
|
||||
//#define FRSKYX_CC2500_INO
|
||||
|
||||
//Update this table to set which protocol/sub_protocol is called for the corresponding dial number
|
||||
static const uint8_t PPM_prot[15][2]= { {MODE_FLYSKY , Flysky }, //Dial=1
|
||||
{MODE_HUBSAN , 0 }, //Dial=2
|
||||
{MODE_FRSKY , 0 }, //Dial=3
|
||||
{MODE_HISKY , Hisky }, //Dial=4
|
||||
{MODE_V2X2 , 0 }, //Dial=5
|
||||
{MODE_DSM2 , DSM2 }, //Dial=6
|
||||
{MODE_DEVO , 0 }, //Dial=7
|
||||
{MODE_YD717 , YD717 }, //Dial=8
|
||||
{MODE_KN , WLTOYS }, //Dial=9
|
||||
{MODE_SYMAX , SYMAX }, //Dial=10
|
||||
{MODE_SLT , 0 }, //Dial=11
|
||||
{MODE_CX10 , CX10_BLUE }, //Dial=12
|
||||
{MODE_CG023 , CG023 }, //Dial=13
|
||||
{MODE_BAYANG , 0 }, //Dial=14
|
||||
{MODE_SYMAX , SYMAX5C } //Dial=15
|
||||
};
|
||||
|
||||
//CC2500 RF module frequency adjustment, use in case you cannot bind with Frsky RX
|
||||
//Note: this is set via Option when serial protocol is used
|
||||
//values from 0-127 offset increase frequency, values from 255 to 127 decrease base frequency
|
||||
//uint8_t fine = 0x00;
|
||||
uint8_t fine = 0xd7; //* 215=-41 *
|
||||
|
||||
// Multiprotocol module configuration ends here
|
||||
//******************************************************
|
||||
//******************************************************
|
||||
|
||||
//Multiprotocol module configuration file
|
||||
#include "_Config.h"
|
||||
|
||||
//Global constants/variables
|
||||
|
||||
@ -132,11 +71,7 @@ uint8_t mode_select;
|
||||
uint8_t protocol_flags=0,protocol_flags2=0;
|
||||
|
||||
// Serial variables
|
||||
#if defined(NUM_SERIAL_CH_8) //8 channels serial protocol
|
||||
#define RXBUFFER_SIZE 14
|
||||
#else //16 channels serial protocol
|
||||
#define RXBUFFER_SIZE 25
|
||||
#endif
|
||||
#define TXBUFFER_SIZE 12
|
||||
volatile uint8_t rx_buff[RXBUFFER_SIZE];
|
||||
volatile uint8_t rx_ok_buff[RXBUFFER_SIZE];
|
||||
@ -213,18 +148,22 @@ void setup()
|
||||
LED_SET_OUTPUT;
|
||||
|
||||
// Read or create protocol id
|
||||
MProtocol_id=random_id(10,false);
|
||||
MProtocol_id_master=MProtocol_id;
|
||||
MProtocol_id_master=random_id(10,false);
|
||||
|
||||
|
||||
//Set power transmission flags
|
||||
POWER_FLAG_on; //By default high power for everything
|
||||
|
||||
//Protocol and interrupts initialization
|
||||
if(mode_select != MODE_SERIAL)
|
||||
{ // PPM
|
||||
cur_protocol[0]= PPM_prot[mode_select-1][0];
|
||||
sub_protocol = PPM_prot[mode_select-1][1];
|
||||
protocol_init(cur_protocol[0]);
|
||||
mode_select--;
|
||||
cur_protocol[0] = PPM_prot[mode_select].protocol;
|
||||
sub_protocol = PPM_prot[mode_select].sub_proto;
|
||||
MProtocol_id = PPM_prot[mode_select].rx_num + MProtocol_id_master;
|
||||
option = PPM_prot[mode_select].option;
|
||||
if(PPM_prot[mode_select].power) POWER_FLAG_on;
|
||||
if(PPM_prot[mode_select].autobind) AUTOBIND_FLAG_on;
|
||||
mode_select++;
|
||||
|
||||
protocol_init();
|
||||
|
||||
//Configure PPM interrupt
|
||||
EICRA |=(1<<ISC11); // The rising edge of INT1 pin D3 generates an interrupt request
|
||||
@ -250,7 +189,7 @@ void loop()
|
||||
{ // Protocol needs to be changed
|
||||
LED_OFF; //led off during protocol init
|
||||
module_reset(); //reset previous module
|
||||
protocol_init(cur_protocol[0]&0x1F); //init new protocol
|
||||
protocol_init(); //init new protocol
|
||||
CHANGE_PROTOCOL_FLAG_off; //done
|
||||
}
|
||||
}
|
||||
@ -341,7 +280,8 @@ static void CheckTimer(uint16_t (*cb)(void))
|
||||
}
|
||||
}
|
||||
|
||||
static void protocol_init(uint8_t protocol)
|
||||
// Protocol start
|
||||
static void protocol_init()
|
||||
{
|
||||
uint16_t next_callback=0; // Default is immediate call back
|
||||
remote_callback = 0;
|
||||
@ -358,7 +298,7 @@ static void protocol_init(uint8_t protocol)
|
||||
CTRL1_on; //NRF24L01 antenna RF3 by default
|
||||
CTRL2_off; //NRF24L01 antenna RF3 by default
|
||||
|
||||
switch(protocol) // Init the requested protocol
|
||||
switch(cur_protocol[0]&0x1F) // Init the requested protocol
|
||||
{
|
||||
#if defined(FLYSKY_A7105_INO)
|
||||
case MODE_FLYSKY:
|
||||
@ -496,7 +436,6 @@ static void update_serial_data()
|
||||
POWER_FLAG_on; //power high
|
||||
|
||||
option=rx_ok_buff[2];
|
||||
fine=option; // Update FrSky fine tuning
|
||||
|
||||
if( ((rx_ok_buff[0]&0x5F) != (cur_protocol[0]&0x5F)) || ( (rx_ok_buff[1]&0x7F) != cur_protocol[1] ) )
|
||||
{ // New model has been selected
|
||||
@ -511,19 +450,7 @@ static void update_serial_data()
|
||||
CHANGE_PROTOCOL_FLAG_on; //restart protocol with bind
|
||||
cur_protocol[0] = rx_ok_buff[0]; //store current protocol
|
||||
|
||||
// decode channel values
|
||||
#if defined(NUM_SERIAL_CH_8) //8 channels serial protocol
|
||||
Servo_data[0]=rx_ok_buff[3]+((rx_ok_buff[11]&0xC0)<<2);
|
||||
Servo_data[1]=rx_ok_buff[4]+((rx_ok_buff[11]&0x30)<<4);
|
||||
Servo_data[2]=rx_ok_buff[5]+((rx_ok_buff[11]&0x0C)<<6);
|
||||
Servo_data[3]=rx_ok_buff[6]+((rx_ok_buff[11]&0x03)<<8);
|
||||
Servo_data[4]=rx_ok_buff[7]+((rx_ok_buff[12]&0xC0)<<2);
|
||||
Servo_data[5]=rx_ok_buff[8]+((rx_ok_buff[12]&0x30)<<4);
|
||||
Servo_data[6]=rx_ok_buff[9]+((rx_ok_buff[12]&0x0C)<<6);
|
||||
Servo_data[7]=rx_ok_buff[10]+((rx_ok_buff[12]&0x03)<<8);
|
||||
for(uint8_t i=0;i<8;i++)
|
||||
Servo_data[i]=((Servo_data[i]*5)>>2)+860; //range 860-2140;
|
||||
#else //16 channels serial protocol
|
||||
// decode channel values
|
||||
volatile uint8_t *p=rx_ok_buff+2;
|
||||
uint8_t dec=-3;
|
||||
for(uint8_t i=0;i<NUM_CHN;i++)
|
||||
@ -537,7 +464,6 @@ static void update_serial_data()
|
||||
p++;
|
||||
Servo_data[i]=((((*((uint32_t *)p))>>dec)&0x7FF)*5)/8+860; //value range 860<->2140 -125%<->+125%
|
||||
}
|
||||
#endif
|
||||
RX_FLAG_off; //data has been processed
|
||||
}
|
||||
|
||||
@ -617,16 +543,6 @@ uint16_t limit_channel_100(uint8_t ch)
|
||||
return Servo_data[ch];
|
||||
}
|
||||
|
||||
// Convert 32b id to rx_tx_addr
|
||||
static void set_rx_tx_addr(uint32_t id)
|
||||
{ // Used by almost all protocols
|
||||
rx_tx_addr[0] = (id >> 24) & 0xFF;
|
||||
rx_tx_addr[1] = (id >> 16) & 0xFF;
|
||||
rx_tx_addr[2] = (id >> 8) & 0xFF;
|
||||
rx_tx_addr[3] = (id >> 0) & 0xFF;
|
||||
rx_tx_addr[4] = 0xC1; // for YD717: always uses first data port
|
||||
}
|
||||
|
||||
#if defined(TELEMETRY)
|
||||
void Serial_write(uint8_t data)
|
||||
{
|
||||
@ -641,21 +557,12 @@ void Serial_write(uint8_t data)
|
||||
|
||||
static void Mprotocol_serial_init()
|
||||
{
|
||||
#if defined(NUM_SERIAL_CH_8) //8 channels serial protocol
|
||||
#define BAUD 125000
|
||||
#include <util/setbaud.h>
|
||||
UBRR0H = UBRRH_VALUE;
|
||||
UBRR0L = UBRRL_VALUE;
|
||||
//Set frame format to 8 data bits, no parity, 1 stop bit
|
||||
UCSR0C |= (1<<UCSZ01)|(1<<UCSZ00);
|
||||
#else //16 channels serial protocol
|
||||
#define BAUD 100000
|
||||
#include <util/setbaud.h>
|
||||
UBRR0H = UBRRH_VALUE;
|
||||
UBRR0L = UBRRL_VALUE;
|
||||
//Set frame format to 8 data bits, even parity, 2 stop bits
|
||||
UCSR0C |= (1<<UPM01)|(1<<USBS0)|(1<<UCSZ01)|(1<<UCSZ00);
|
||||
#endif
|
||||
while ( UCSR0A & (1 << RXC0) )//flush receive buffer
|
||||
UDR0;
|
||||
//enable reception and RC complete interrupt
|
||||
@ -663,6 +570,16 @@ static void Mprotocol_serial_init()
|
||||
UCSR0B |= (1<<TXEN0);//tx enable
|
||||
}
|
||||
|
||||
// Convert 32b id to rx_tx_addr
|
||||
static void set_rx_tx_addr(uint32_t id)
|
||||
{ // Used by almost all protocols
|
||||
rx_tx_addr[0] = (id >> 24) & 0xFF;
|
||||
rx_tx_addr[1] = (id >> 16) & 0xFF;
|
||||
rx_tx_addr[2] = (id >> 8) & 0xFF;
|
||||
rx_tx_addr[3] = (id >> 0) & 0xFF;
|
||||
rx_tx_addr[4] = 0xC1; // for YD717: always uses first data port
|
||||
}
|
||||
|
||||
static uint32_t random_id(uint16_t adress, uint8_t create_new)
|
||||
{
|
||||
uint32_t id;
|
||||
@ -694,6 +611,7 @@ static uint32_t random_id(uint16_t adress, uint8_t create_new)
|
||||
/**************************/
|
||||
/**************************/
|
||||
|
||||
//PPM
|
||||
ISR(INT1_vect)
|
||||
{ // Interrupt on PPM pin
|
||||
static int8_t chan=-1;
|
||||
@ -722,53 +640,7 @@ ISR(INT1_vect)
|
||||
Prev_TCNT1+=Cur_TCNT1;
|
||||
}
|
||||
|
||||
#if defined(TELEMETRY)
|
||||
ISR(USART_UDRE_vect)
|
||||
{ // Transmit interrupt
|
||||
uint8_t t = tx_tail;
|
||||
if(tx_head!=t)
|
||||
{
|
||||
if(++t>=TXBUFFER_SIZE)//head
|
||||
t=0;
|
||||
UDR0=tx_buff[t];
|
||||
tx_tail=t;
|
||||
}
|
||||
if (t == tx_head)
|
||||
UCSR0B &= ~(1<<UDRIE0); // Check if all data is transmitted . if yes disable transmitter UDRE interrupt
|
||||
}
|
||||
#endif
|
||||
|
||||
#if defined(NUM_SERIAL_CH_8) //8 channels serial protocol
|
||||
ISR(USART_RX_vect)
|
||||
{ // RX interrupt
|
||||
static uint16_t crc = 0;
|
||||
|
||||
if(idx==0)
|
||||
{ // Let's try to sync at this point
|
||||
OCR1B=TCNT1+5000L; // timer for 2500us
|
||||
TIFR1=(1<<OCF1B); // clear OCR1B match flag
|
||||
TIMSK1 |=(1<<OCIE1B); // enable interrupt on compare B match
|
||||
crc=0;
|
||||
}
|
||||
if(idx<RXBUFFER_SIZE-1)
|
||||
{ // Store bytes in buffer and calculate crc as we go
|
||||
rx_buff[idx]=UDR0;
|
||||
crc = (crc<<8) ^ pgm_read_word(&CRCTable[((uint8_t)(crc>>8) ^ rx_buff[idx++]) & 0xFF]);
|
||||
}
|
||||
else
|
||||
{ // A frame has been received and needs to be checked before giving it to main
|
||||
TIMSK1 &=~(1<<OCIE1B); // disable interrupt on compare B match
|
||||
if(UDR0==(uint8_t)(crc & 0xFF) && !IS_RX_FLAG_on)
|
||||
{ //Good frame received and main has finished with previous buffer
|
||||
for(idx=0;idx<RXBUFFER_SIZE;idx++)
|
||||
rx_ok_buff[idx]=rx_buff[idx]; // Duplicate the buffer
|
||||
RX_FLAG_on; //flag for main to process servo data
|
||||
LED_ON;
|
||||
}
|
||||
idx=0;
|
||||
}
|
||||
}
|
||||
#else //16 channels serial protocol
|
||||
//Serial RX
|
||||
ISR(USART_RX_vect)
|
||||
{ // RX interrupt
|
||||
if((UCSR0A&0x1C)==0) // Check frame error, data overrun and parity error
|
||||
@ -805,9 +677,26 @@ ISR(USART_RX_vect)
|
||||
idx=0; // Error encountered discard full frame...
|
||||
}
|
||||
}
|
||||
#endif
|
||||
|
||||
//Serial timer
|
||||
ISR(TIMER1_COMPB_vect)
|
||||
{ // Timer1 compare B interrupt
|
||||
idx=0;
|
||||
}
|
||||
|
||||
#if defined(TELEMETRY)
|
||||
//Serial TX
|
||||
ISR(USART_UDRE_vect)
|
||||
{ // Transmit interrupt
|
||||
uint8_t t = tx_tail;
|
||||
if(tx_head!=t)
|
||||
{
|
||||
if(++t>=TXBUFFER_SIZE)//head
|
||||
t=0;
|
||||
UDR0=tx_buff[t];
|
||||
tx_tail=t;
|
||||
}
|
||||
if (t == tx_head)
|
||||
UCSR0B &= ~(1<<UDRIE0); // Check if all data is transmitted . if yes disable transmitter UDRE interrupt
|
||||
}
|
||||
#endif
|
||||
|
||||
220
Multiprotocol/_Config.h
Normal file
220
Multiprotocol/_Config.h
Normal file
@ -0,0 +1,220 @@
|
||||
/*
|
||||
This project is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 3 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
Multiprotocol is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with Multiprotocol. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
/** Multiprotocol module configuration file ***/
|
||||
|
||||
//Uncomment your TX type
|
||||
#define TX_ER9X //ER9X AETR (988<->2012µs)
|
||||
//#define TX_DEVO7 //DEVO7 EATR (1120<->1920µs)
|
||||
//#define TX_SPEKTRUM //Spektrum TAER (1100<->1900µs)
|
||||
//#define TX_HISKY //HISKY AETR (1100<->1900µs)
|
||||
|
||||
//Uncomment to enable telemetry
|
||||
#define TELEMETRY
|
||||
|
||||
//Comment a protocol to exclude it from compilation
|
||||
#define BAYANG_NRF24L01_INO
|
||||
#define CG023_NRF24L01_INO
|
||||
#define CX10_NRF24L01_INO
|
||||
#define DEVO_CYRF6936_INO
|
||||
#define DSM2_CYRF6936_INO
|
||||
#define ESKY_NRF24L01_INO
|
||||
#define FLYSKY_A7105_INO
|
||||
#define FRSKY_CC2500_INO
|
||||
#define HISKY_NRF24L01_INO
|
||||
#define HUBSAN_A7105_INO
|
||||
#define KN_NRF24L01_INO
|
||||
#define SLT_NRF24L01_INO
|
||||
#define SYMAX_NRF24L01_INO
|
||||
#define V2X2_NRF24L01_INO
|
||||
#define YD717_NRF24L01_INO
|
||||
//#define FRSKYX_CC2500_INO
|
||||
|
||||
//Update this table to set which protocol and all associated settings are called for the corresponding dial number
|
||||
static const PPM_Parameters PPM_prot[15]=
|
||||
{
|
||||
// Protocol Sub protocol RX_Num Power Auto Bind Option
|
||||
{MODE_FLYSKY, Flysky , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=1
|
||||
{MODE_HUBSAN, 0 , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=2
|
||||
{MODE_FRSKY , 0 , 0 , P_HIGH , NO_AUTOBIND , 0xD7 }, //Dial=3
|
||||
{MODE_HISKY , Hisky , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=4
|
||||
{MODE_V2X2 , 0 , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=5
|
||||
{MODE_DSM2 , DSM2 , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=6
|
||||
{MODE_DEVO , 0 , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=7
|
||||
{MODE_YD717 , YD717 , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=8
|
||||
{MODE_KN , WLTOYS , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=9
|
||||
{MODE_SYMAX , SYMAX , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=10
|
||||
{MODE_SLT , 0 , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=11
|
||||
{MODE_CX10 , CX10_BLUE , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=12
|
||||
{MODE_CG023 , CG023 , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=13
|
||||
{MODE_BAYANG, 0 , 0 , P_HIGH , NO_AUTOBIND , 0 }, //Dial=14
|
||||
{MODE_SYMAX , SYMAX5C , 0 , P_HIGH , NO_AUTOBIND , 0 } //Dial=15
|
||||
};
|
||||
/* Available protocols and associated sub protocols:
|
||||
MODE_FLYSKY
|
||||
Flysky
|
||||
V9X9
|
||||
V6X6
|
||||
V912
|
||||
MODE_HUBSAN
|
||||
NONE
|
||||
MODE_FRSKY
|
||||
NONE
|
||||
MODE_HISKY
|
||||
Hisky
|
||||
HK310
|
||||
MODE_V2X2
|
||||
NONE
|
||||
MODE_DSM2
|
||||
DSM2
|
||||
DSMX
|
||||
MODE_DEVO
|
||||
NONE
|
||||
MODE_YD717
|
||||
YD717
|
||||
SKYWLKR
|
||||
SYMAX4
|
||||
XINXUN
|
||||
NIHUI
|
||||
MODE_KN
|
||||
WLTOYS
|
||||
FEILUN
|
||||
MODE_SYMAX
|
||||
SYMAX
|
||||
SYMAX5C
|
||||
MODE_SLT
|
||||
NONE
|
||||
MODE_CX10
|
||||
CX10_GREEN
|
||||
CX10_BLUE
|
||||
DM007
|
||||
Q282
|
||||
JC3015_1
|
||||
JC3015_2
|
||||
MK33041
|
||||
MODE_CG023
|
||||
CG023
|
||||
YD829
|
||||
H8_3D
|
||||
MODE_BAYANG
|
||||
NONE
|
||||
MODE_FRSKYX
|
||||
NONE
|
||||
MODE_ESKY
|
||||
NONE
|
||||
|
||||
RX_Num value between 0 and 15
|
||||
|
||||
Power P_HIGH or P_LOW
|
||||
|
||||
Auto Bind AUTOBIND or NO_AUTOBIND
|
||||
|
||||
Option value between 0 and 255. 0xD7 or 0x00 for Frsky fine tuning.
|
||||
*/
|
||||
|
||||
//******************
|
||||
//TX definitions with timing endpoints and channels order
|
||||
|
||||
// Turnigy PPM and channels
|
||||
#if defined(TX_ER9X)
|
||||
#define PPM_MAX 2140
|
||||
#define PPM_MIN 860
|
||||
#define PPM_MAX_100 2012
|
||||
#define PPM_MIN_100 988
|
||||
enum chan_order{
|
||||
AILERON =0,
|
||||
ELEVATOR,
|
||||
THROTTLE,
|
||||
RUDDER,
|
||||
AUX1,
|
||||
AUX2,
|
||||
AUX3,
|
||||
AUX4,
|
||||
AUX5,
|
||||
AUX6,
|
||||
AUX7,
|
||||
AUX8
|
||||
};
|
||||
#endif
|
||||
|
||||
// Devo PPM and channels
|
||||
#if defined(TX_DEVO7)
|
||||
#define PPM_MAX 2100
|
||||
#define PPM_MIN 900
|
||||
#define PPM_MAX_100 1920
|
||||
#define PPM_MIN_100 1120
|
||||
enum chan_order{
|
||||
ELEVATOR=0,
|
||||
AILERON,
|
||||
THROTTLE,
|
||||
RUDDER,
|
||||
AUX1,
|
||||
AUX2,
|
||||
AUX3,
|
||||
AUX4,
|
||||
AUX5,
|
||||
AUX6,
|
||||
AUX7,
|
||||
AUX8
|
||||
};
|
||||
#endif
|
||||
|
||||
// SPEKTRUM PPM and channels
|
||||
#if defined(TX_SPEKTRUM)
|
||||
#define PPM_MAX 2000
|
||||
#define PPM_MIN 1000
|
||||
#define PPM_MAX_100 1900
|
||||
#define PPM_MIN_100 1100
|
||||
enum chan_order{
|
||||
THROTTLE=0,
|
||||
AILERON,
|
||||
ELEVATOR,
|
||||
RUDDER,
|
||||
AUX1,
|
||||
AUX2,
|
||||
AUX3,
|
||||
AUX4,
|
||||
AUX5,
|
||||
AUX6,
|
||||
AUX7,
|
||||
AUX8
|
||||
};
|
||||
#endif
|
||||
|
||||
// HISKY
|
||||
#if defined(TX_HISKY)
|
||||
#define PPM_MAX 2000
|
||||
#define PPM_MIN 1000
|
||||
#define PPM_MAX_100 1900
|
||||
#define PPM_MIN_100 1100
|
||||
enum chan_order{
|
||||
AILERON =0,
|
||||
ELEVATOR,
|
||||
THROTTLE,
|
||||
RUDDER,
|
||||
AUX1,
|
||||
AUX2,
|
||||
AUX3,
|
||||
AUX4,
|
||||
AUX5,
|
||||
AUX6,
|
||||
AUX7,
|
||||
AUX8
|
||||
};
|
||||
#endif
|
||||
|
||||
#define PPM_MIN_COMMAND 1250
|
||||
#define PPM_SWITCH 1550
|
||||
#define PPM_MAX_COMMAND 1750
|
||||
@ -87,101 +87,21 @@ enum CG023
|
||||
H8_3D = 2
|
||||
};
|
||||
|
||||
//******************
|
||||
//TX definitions with timing endpoints and channels order
|
||||
//******************
|
||||
#define NONE 0
|
||||
#define P_HIGH 1
|
||||
#define P_LOW 0
|
||||
#define AUTOBIND 1
|
||||
#define NO_AUTOBIND 0
|
||||
|
||||
// Turnigy PPM and channels
|
||||
#if defined(TX_ER9X)
|
||||
#define PPM_MAX 2140
|
||||
#define PPM_MIN 860
|
||||
#define PPM_MAX_100 2012
|
||||
#define PPM_MIN_100 988
|
||||
enum chan_order{
|
||||
AILERON =0,
|
||||
ELEVATOR,
|
||||
THROTTLE,
|
||||
RUDDER,
|
||||
AUX1,
|
||||
AUX2,
|
||||
AUX3,
|
||||
AUX4,
|
||||
AUX5,
|
||||
AUX6,
|
||||
AUX7,
|
||||
AUX8
|
||||
struct PPM_Parameters
|
||||
{
|
||||
uint8_t protocol : 5;
|
||||
uint8_t sub_proto : 3;
|
||||
uint8_t rx_num : 4;
|
||||
uint8_t power : 1;
|
||||
uint8_t autobind : 1;
|
||||
uint8_t option;
|
||||
};
|
||||
#endif
|
||||
|
||||
// Devo PPM and channels
|
||||
#if defined(TX_DEVO7)
|
||||
#define PPM_MAX 2100
|
||||
#define PPM_MIN 900
|
||||
#define PPM_MAX_100 1920
|
||||
#define PPM_MIN_100 1120
|
||||
enum chan_order{
|
||||
ELEVATOR=0,
|
||||
AILERON,
|
||||
THROTTLE,
|
||||
RUDDER,
|
||||
AUX1,
|
||||
AUX2,
|
||||
AUX3,
|
||||
AUX4,
|
||||
AUX5,
|
||||
AUX6,
|
||||
AUX7,
|
||||
AUX8
|
||||
};
|
||||
#endif
|
||||
|
||||
// SPEKTRUM PPM and channels
|
||||
#if defined(TX_SPEKTRUM)
|
||||
#define PPM_MAX 2000
|
||||
#define PPM_MIN 1000
|
||||
#define PPM_MAX_100 1900
|
||||
#define PPM_MIN_100 1100
|
||||
enum chan_order{
|
||||
THROTTLE=0,
|
||||
AILERON,
|
||||
ELEVATOR,
|
||||
RUDDER,
|
||||
AUX1,
|
||||
AUX2,
|
||||
AUX3,
|
||||
AUX4,
|
||||
AUX5,
|
||||
AUX6,
|
||||
AUX7,
|
||||
AUX8
|
||||
};
|
||||
#endif
|
||||
|
||||
// HISKY
|
||||
#if defined(TX_HISKY)
|
||||
#define PPM_MAX 2000
|
||||
#define PPM_MIN 1000
|
||||
#define PPM_MAX_100 1900
|
||||
#define PPM_MIN_100 1100
|
||||
enum chan_order{
|
||||
AILERON =0,
|
||||
ELEVATOR,
|
||||
THROTTLE,
|
||||
RUDDER,
|
||||
AUX1,
|
||||
AUX2,
|
||||
AUX3,
|
||||
AUX4,
|
||||
AUX5,
|
||||
AUX6,
|
||||
AUX7,
|
||||
AUX8
|
||||
};
|
||||
#endif
|
||||
|
||||
#define PPM_MIN_COMMAND 1250
|
||||
#define PPM_SWITCH 1550
|
||||
#define PPM_MAX_COMMAND 1750
|
||||
|
||||
//*******************
|
||||
//*** Pinouts ***
|
||||
@ -523,86 +443,5 @@ Serial: 100000 Baud 8e2 _ xxxx xxxx p --
|
||||
1843 +100%
|
||||
2047 +125%
|
||||
Channels bits are concatenated to fit in 22 bytes like in SBUS protocol
|
||||
|
||||
|
||||
**************************
|
||||
8 channels serial protocol
|
||||
**************************
|
||||
Serial: 125000 Baud 8n1 _ xxxx xxxx - ---
|
||||
Channels:
|
||||
Nbr=8
|
||||
10bits=0..1023
|
||||
0 -125%
|
||||
96 -100%
|
||||
512 0%
|
||||
928 +100%
|
||||
1023 +125%
|
||||
Stream[0] = sub_protocol|BindBit|RangeCheckBit|AutoBindBit;
|
||||
sub_protocol is 0..31 (bits 0..4)
|
||||
=> Reserved 0
|
||||
Flysky 1
|
||||
Hubsan 2
|
||||
Frsky 3
|
||||
Hisky 4
|
||||
V2x2 5
|
||||
DSM2 6
|
||||
Devo 7
|
||||
YD717 8
|
||||
KN 9
|
||||
SymaX 10
|
||||
SLT 11
|
||||
CX10 12
|
||||
CG023 13
|
||||
Bayang 14
|
||||
FrskyX 15
|
||||
ESky 16
|
||||
BindBit=> 0x80 1=Bind/0=No
|
||||
AutoBindBit=> 0x40 1=Yes /0=No
|
||||
RangeCheck=> 0x20 1=Yes /0=No
|
||||
Stream[1] = RxNum | Power | Type;
|
||||
RxNum value is 0..15 (bits 0..3)
|
||||
Type is 0..7 <<4 (bit 4..6)
|
||||
sub_protocol==Flysky
|
||||
Flysky 0
|
||||
V9x9 1
|
||||
V6x6 2
|
||||
V912 3
|
||||
sub_protocol==Hisky
|
||||
Hisky 0
|
||||
HK310 1
|
||||
sub_protocol==DSM2
|
||||
DSM2 0
|
||||
DSMX 1
|
||||
sub_protocol==YD717
|
||||
YD717 0
|
||||
SKYWLKR 1
|
||||
SYMAX4 2
|
||||
XINXUN 3
|
||||
NIHUI 4
|
||||
sub_protocol==KN
|
||||
WLTOYS 0
|
||||
FEILUN 1
|
||||
sub_protocol==SYMAX
|
||||
SYMAX 0
|
||||
SYMAX5C 1
|
||||
sub_protocol==CX10
|
||||
CX10_GREEN 0
|
||||
CX10_BLUE 1 // also compatible with CX10-A, CX12
|
||||
DM007 2
|
||||
Q282 3
|
||||
JC3015_1 4
|
||||
JC3015_2 5
|
||||
MK33041 6
|
||||
sub_protocol==CG023
|
||||
CG023 0
|
||||
YD829 1
|
||||
H8_3D 2
|
||||
Power value => 0x80 0=High/1=Low
|
||||
Stream[2] = option_protocol;
|
||||
option_protocol value is -127..127
|
||||
Stream[i+3] = lowByte(channel[i]) // with i[0..7]
|
||||
Stream[11] = highByte(channel[0])<<6 | highByte(channel[1])<<4 | highByte(channel[2])<<2 | highByte(channel[3])
|
||||
Stream[12] = highByte(channel[4])<<6 | highByte(channel[5])<<4 | highByte(channel[6])<<2 | highByte(channel[7])
|
||||
Stream[13] = lowByte(CRC16(Stream[0..12])
|
||||
*/
|
||||
|
||||
|
||||
23
README.md
23
README.md
@ -26,12 +26,21 @@ The source code is partly based on the Deviation TX project, thanks to all the d
|
||||
###Using standard PPM output (trainer port)
|
||||
The multiprotocol TX module can be used on any TX with a trainer port.
|
||||
|
||||
Channels order is AETR by default but can be changed in the source code.
|
||||
Channels order is AETR by default but can be changed in the _Config.h.
|
||||
|
||||
The protocol selection is done via a dip switch or a rotary dip switch for access to up to 15 different protocols.
|
||||
The protocol selection is done via a dip switch or a rotary dip switch.
|
||||
|
||||
|
||||
|
||||
You can access to up to 15 different protocols and associated settings.
|
||||
|
||||
Settings per selection are located in _Config.h:
|
||||
- Protocol and type: many main protocols have variants
|
||||
- RX Num: number your different RXs and make sure only one model will react to the commands
|
||||
- Power: High or low, enables to lower the power setting of your TX (indoor for example).
|
||||
- Option: -127..+127 allowing to set specific protocol options. Like for Hubsan to set the video frequency.
|
||||
- Autobind: Yes or No. At the model selection (or power applied to the TX) a bind sequence will be initiated
|
||||
|
||||
###Using a serial output
|
||||
The multiprotocol TX module takes full advantage of being used on a Turnigy 9X, 9XR, 9XR Pro, Taranis, 9Xtreme, AR9X, ... running [er9x or ersky9X](https://github.com/MikeBland/mbtx/tree/next). (A version for OpenTX is being looked at)
|
||||
|
||||
@ -50,8 +59,8 @@ Options are:
|
||||
|
||||
Notes:
|
||||
- Using this solution does not need any modification of the TX since it uses the TX module slot PPM pin for serial transfer.
|
||||
- There are 2 versions of serial protocol either 8 or 16 channels. 16 channels is the latest version. Make sure to use the right version based on your version of er9x/ersky9x.
|
||||
- Channels order is AETR by default but can be changed in the source code.
|
||||
- There are 2 versions of serial protocol either 8 or 16 channels. 16 channels is the latest and only available version going forward. Make sure to use the right version based on your version of er9x/ersky9x.
|
||||
- Channels order is AETR by default but can be changed in _Config.h.
|
||||
|
||||
###Telemetry
|
||||
Telemetry is available for er9x and ersky9x TXs.
|
||||
@ -85,7 +94,7 @@ Notes:
|
||||
###Protocol selection
|
||||
|
||||
####Using the dial for PPM input
|
||||
PPM is only allowing access to a subset of existing protocols & sub_protocols.
|
||||
PPM is only allowing access to a subset of existing protocols.
|
||||
The default association dial position / protocol is listed below.
|
||||
|
||||
Dial|Protocol|Sub_protocol|RF Module
|
||||
@ -109,7 +118,7 @@ Dial|Protocol|Sub_protocol|RF Module
|
||||
|
||||
Notes:
|
||||
- The dial selection must be done before the power is applied.
|
||||
- The protocols and subprotocols accessible by the dial can be personalized by modifying the source code.
|
||||
- The protocols, subprotocols and all other settings can be personalized by modifying the _Config.h file.
|
||||
|
||||
####Using serial input with er9x/ersky9x
|
||||
Serial is allowing access to all existing protocols & sub_protocols listed below.
|
||||
@ -455,7 +464,7 @@ Arduino 1.6.5
|
||||
|
||||
Compilation of the code posted here works. So if it doesn't for you this is a problem with your setup, please double check everything before asking.
|
||||
|
||||
Multiprotocol.ino header can be modified to compile with/without some protocols, change protocols/sub_protocols associated with dial for PPM input, different channel orders, different channels timing, 8 or 16 channels serial protocol, Telemetry or not, ...
|
||||
_Config.h file can be modified to compile with/without some protocols, change protocols/sub_protocols/settings associated with dial for PPM input, different channel orders, different channels timing, Telemetry or not, ...
|
||||
|
||||
###Upload the code using ISP (In System Programming)
|
||||
It is recommended to use an external programmer like [USBASP](http://www.banggood.com/USBASP-USBISP-3_3-5V-AVR-Downloader-Programmer-With-ATMEGA8-ATMEGA128-p-934425.html) to upload the code in the Atmega328. The programmer should be set to 3.3V or nothing to not supply any over voltage to the multimodule and avoid any damages.
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user