DIY-Multiprotocol-TX-Module/Multiprotocol/MultiOrange.cpp.xmega

#define ARDUINO_AVR_PRO		1
//#define __AVR_ATmega328P__	1

#define XMEGA	1

#include <stdlib.h>
#include <string.h>
#include <avr/interrupt.h>

static void protocol_init(void) ;
static void update_aux_flags(void) ;
static void PPM_Telemetry_serial_init(void) ;
static uint32_t random_id(uint16_t adress, uint8_t create_new) ;
static void update_serial_data(void) ;
static void Mprotocol_serial_init(void) ;
static void module_reset(void) ;
static void update_led_status(void) ;
static void set_rx_tx_addr(uint32_t id) ;
uint16_t limit_channel_100(uint8_t ch) ;


extern void NRF24L01_Reset(void ) ;
extern void A7105_Reset(void ) ;
extern void CC2500_Reset(void ) ;
extern uint8_t CYRF_Reset(void ) ;
extern void CYRF_SetTxRxMode(uint8_t mode) ;

extern void frskyUpdate(void) ;
extern uint16_t initDsm2(void) ;
extern uint16_t ReadDsm2(void) ;
extern uint16_t DevoInit(void) ;
extern uint16_t devo_callback(void) ;

extern void randomSeed(unsigned int seed) ;
extern long random(long howbig) ;
extern long map(long x, long in_min, long in_max, long out_min, long out_max) ;

extern uint32_t millis(void) ;
extern uint32_t micros(void) ;
extern void delayMicroseconds(uint16_t x) ;
extern void init(void) ;

extern int analogRead(uint8_t pin) ;

#define A6 20
#define A7 21

#define yield()

//void _delay_us( uint16_t x )
//{
//	delayMicroseconds( x ) ;
//}

#define clockCyclesPerMicrosecond() ( F_CPU / 1000000L )
#define clockCyclesToMicroseconds(a) ( (a) / clockCyclesPerMicrosecond() )

// the prescaler is set so that timer0 ticks every 64 clock cycles, and the
// the overflow handler is called every 256 ticks.
#define MICROSECONDS_PER_TIMER0_OVERFLOW (clockCyclesToMicroseconds(64 * 256))

// the whole number of milliseconds per timer0 overflow
#define MILLIS_INC (MICROSECONDS_PER_TIMER0_OVERFLOW / 1000)

// the fractional number of milliseconds per timer0 overflow. we shift right
// by three to fit these numbers into a byte. (for the clock speeds we care
// about - 8 and 16 MHz - this doesn't lose precision.)
#define FRACT_INC ((MICROSECONDS_PER_TIMER0_OVERFLOW % 1000) >> 3)
#define FRACT_MAX (1000 >> 3)

volatile unsigned long timer0_overflow_count = 0;
volatile unsigned long timer0_millis = 0;
static unsigned char timer0_fract = 0;



//void chipInit()
//{
//	PR.PRGEN = 0 ;		// RTC and event system active
//	PR.PRPC = 0 ;		// No power reduction port C
//	PR.PRPD = 0 ;    // No power reduction port D
//	PMIC.CTRL = 7 ;
//	OSC.CTRL = 0xC3 ;	// unclear	
//	OSC.CTRL |= 0x08 ;	// Enable external oscillator
//	while( ( OSC.STATUS & 0x08 ) == 0 ) ;	// Wait for ext osc to be ready
//	OSC.PLLCTRL = 0xC2 ;		// Ext. Osc times 2
//	OSC.CTRL |= 0x10 ;			// Enable PLL
//	while( ( OSC.STATUS & 0x10 ) == 0 ) ;	// Wait PLL ready
//	CPU_CCP = 0xD8 ; // 0x34
//	CLK.CTRL = 0 ;			// Select 2MHz internal clock
//	CPU_CCP = 0xD8 ; // 0x34
//	CLK.CTRL = 0x04 ;	// Select PLL as clock (32MHz)
//	PORTD.OUTSET = 0x17 ;
//	PORTD.DIRSET = 0xB2 ;
//	PORTD.DIRCLR = 0x4D ;
//	PORTD.PIN0CTRL = 0x18 ;
//	PORTD.PIN2CTRL = 0x18 ;
//	PORTE.DIRSET = 0x01 ;
//	PORTE.DIRCLR = 0x02 ;
//	PORTE.OUTSET = 0x01 ;
//	PORTA.DIRCLR = 0xFF ;
//	PORTA.PIN0CTRL = 0x18 ;
//	PORTA.PIN1CTRL = 0x18 ;
//	PORTA.PIN2CTRL = 0x18 ;
//	PORTA.PIN3CTRL = 0x18 ;
//	PORTA.PIN4CTRL = 0x18 ;
//	PORTA.PIN5CTRL = 0x18 ;
//	PORTA.PIN6CTRL = 0x18 ;
//	PORTA.PIN7CTRL = 0x18 ;
//	PORTC.DIRSET = 0x20 ;
//	PORTC.OUTCLR = 0x20 ;
//	SPID.CTRL = 0x51 ;
//	PORTC.OUTSET = 0x08 ;
//	PORTC.DIRSET = 0x08 ;
//	PORTC.PIN3CTRL = 0x18 ;
//	PORTC.PIN2CTRL = 0x18 ;
//	USARTC0.BAUDCTRLA = 19 ;
//	USARTC0.BAUDCTRLB = 0 ;
//	USARTC0.CTRLB = 0x18 ;
//	USARTC0.CTRLA = (USARTC0.CTRLA & 0xCF) | 0x10 ;
//	USARTC0.CTRLC = 0x03 ;
	
//	TCC0.CTRLB = 0 ;
//	TCC0.CTRLC = 0 ;
//	TCC0.CTRLD = 0 ;
//	TCC0.CTRLE = 0 ;
//	TCC0.INTCTRLA = 0x01 ;
//	TCC0.INTCTRLB = 0 ;
//	TCC0.PER = 0x00FF ;
//	TCC0.CTRLA = 4 ;

//	TCC1.CTRLB = 0 ;
//	TCC1.CTRLC = 0 ;
//	TCC1.CTRLD = 0 ;
//	TCC1.CTRLE = 0 ;
//	TCC1.INTCTRLA = 0x03 ;
//	TCC1.INTCTRLB = 0 ;
//	TCC1.PER = 0xFFFF ;
//	TCC1.CNT = 0 ;
//	TCC1.CTRLA = 4 ;

//	TCD0.CTRLA = 4 ;
//	TCD0.INTCTRLA = 0x03 ;
//	TCD0.PER = 0x02ED ;

////	L0EDB() ;

//	NVM.CTRLB &= 0xF7 ;	// No EEPROM mapping
//}



ISR(TCC0_OVF_vect)
{
	// copy these to local variables so they can be stored in registers
	// (volatile variables must be read from memory on every access)
	unsigned long m = timer0_millis;
	unsigned char f = timer0_fract;

	m += MILLIS_INC;
	f += FRACT_INC;
	if (f >= FRACT_MAX) {
		f -= FRACT_MAX;
		m += 1;
	}

	timer0_fract = f;
	timer0_millis = m;
	timer0_overflow_count++;
}

unsigned long millis()
{
	unsigned long m;
	uint8_t oldSREG = SREG;

	// disable interrupts while we read timer0_millis or we might get an
	// inconsistent value (e.g. in the middle of a write to timer0_millis)
	cli();
	m = timer0_millis;
	SREG = oldSREG;

	return m;
}

unsigned long micros()
{
	unsigned long m;
	uint8_t oldSREG = SREG, t;
	
	cli();
	m = timer0_overflow_count;
	t = TCC0.CNT ;

	if ((TCC0.INTFLAGS & TC0_OVFIF_bm) && (t < 255))
		m++;

	SREG = oldSREG;
	
	return ((m << 8) + t) * (64 / clockCyclesPerMicrosecond());
}

void delayMilliseconds(unsigned long ms)
{
	uint16_t start = (uint16_t)micros();

	while (ms > 0) {
		yield();
		if (((uint16_t)micros() - start) >= 1000) {
			ms--;
			start += 1000;
		}
	}
}

/* Delay for the given number of microseconds.  Assumes a 8 or 16 MHz clock. */
void delayMicroseconds(unsigned int us)
{
	// calling avrlib's delay_us() function with low values (e.g. 1 or
	// 2 microseconds) gives delays longer than desired.
	//delay_us(us);
#if F_CPU >= 20000000L
	// for the 20 MHz clock on rare Arduino boards

	// for a one-microsecond delay, simply wait 2 cycle and return. The overhead
	// of the function call yields a delay of exactly a one microsecond.
	__asm__ __volatile__ (
		"nop" "\n\t"
		"nop"); //just waiting 2 cycle
	if (--us == 0)
		return;

	// the following loop takes a 1/5 of a microsecond (4 cycles)
	// per iteration, so execute it five times for each microsecond of
	// delay requested.
	us = (us<<2) + us; // x5 us

	// account for the time taken in the preceeding commands.
	us -= 2;

#elif F_CPU >= 16000000L
	// for the 16 MHz clock on most Arduino boards

	// for a one-microsecond delay, simply return.  the overhead
	// of the function call yields a delay of approximately 1 1/8 us.
	if (--us == 0)
		return;

	// the following loop takes a quarter of a microsecond (4 cycles)
	// per iteration, so execute it four times for each microsecond of
	// delay requested.
	us <<= 2;

	// account for the time taken in the preceeding commands.
	us -= 2;
#else
	// for the 8 MHz internal clock on the ATmega168

	// for a one- or two-microsecond delay, simply return.  the overhead of
	// the function calls takes more than two microseconds.  can't just
	// subtract two, since us is unsigned; we'd overflow.
	if (--us == 0)
		return;
	if (--us == 0)
		return;

	// the following loop takes half of a microsecond (4 cycles)
	// per iteration, so execute it twice for each microsecond of
	// delay requested.
	us <<= 1;
    
	// partially compensate for the time taken by the preceeding commands.
	// we can't subtract any more than this or we'd overflow w/ small delays.
	us--;
#endif

	// busy wait
	__asm__ __volatile__ (
		"1: sbiw %0,1" "\n\t" // 2 cycles
		"brne 1b" : "=w" (us) : "0" (us) // 2 cycles
	);
}

#ifndef cbi
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
#endif
#ifndef sbi
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
#endif


void init()
{
	// this needs to be called before setup() or some functions won't
	// work there

	// Enable external oscillator (16MHz)
	OSC.XOSCCTRL = OSC_FRQRANGE_12TO16_gc | OSC_XOSCSEL_XTAL_256CLK_gc ;
	OSC.CTRL |= OSC_XOSCEN_bm ;
	while( ( OSC.STATUS & OSC_XOSCRDY_bm ) == 0 )
		/* wait */ ;
	// Enable PLL (*2 = 32MHz)
	OSC.PLLCTRL = OSC_PLLSRC_XOSC_gc | 2 ;
	OSC.CTRL |= OSC_PLLEN_bm ;
	while( ( OSC.STATUS & OSC_PLLRDY_bm ) == 0 )
		/* wait */ ;
	// Switch to PLL clock
	CPU_CCP = 0xD8 ;
	CLK.CTRL = CLK_SCLKSEL_RC2M_gc ;
	CPU_CCP = 0xD8 ;
	CLK.CTRL = CLK_SCLKSEL_PLL_gc ;

	PMIC.CTRL = 7 ;		// Enable all interrupt levels
	sei();
	
	// on the ATmega168, timer 0 is also used for fast hardware pwm
	// (using phase-correct PWM would mean that timer 0 overflowed half as often
	// resulting in different millis() behavior on the ATmega8 and ATmega168)
//#if defined(TCCR0A) && defined(WGM01)
//	sbi(TCCR0A, WGM01);
//	sbi(TCCR0A, WGM00);
//#endif  

	
// TCC0 counts 0-255 at 4uS clock rate
	EVSYS.CH2MUX = 0x80 + 0x07 ;	// Prescaler of 128
	TCC0.CTRLB = 0 ;
	TCC0.CTRLC = 0 ;
	TCC0.CTRLD = 0 ;
	TCC0.CTRLE = 0 ;
	TCC0.INTCTRLA = 0x01 ;
	TCC0.INTCTRLB = 0 ;
	TCC0.PER = 0x00FF ;
	TCC0.CTRLA = 0x0A ;


#if defined(ADCSRA)
	// set a2d prescale factor to 128
	// 16 MHz / 128 = 125 KHz, inside the desired 50-200 KHz range.
	// XXX: this will not work properly for other clock speeds, and
	// this code should use F_CPU to determine the prescale factor.
	sbi(ADCSRA, ADPS2);
	sbi(ADCSRA, ADPS1);
	sbi(ADCSRA, ADPS0);

	// enable a2d conversions
	sbi(ADCSRA, ADEN);
#endif

	// the bootloader connects pins 0 and 1 to the USART; disconnect them
	// here so they can be used as normal digital i/o; they will be
	// reconnected in Serial.begin()
#if defined(UCSRB)
	UCSRB = 0;
#elif defined(UCSR0B)
	UCSR0B = 0;
#endif

	// PPM interrupt
	PORTD.DIRCLR = 0x08 ;	// D3 is input
	PORTD.PIN3CTRL = 0x01 ;	// Rising edge
	PORTD.INT0MASK = 0x08 ;
	PORTD.INTCTRL = 0x02 ;	// Medium level interrupt

// Dip Switch inputs
	PORTA.DIRCLR = 0xFF ;
	PORTA.PIN0CTRL = 0x18 ;
	PORTA.PIN1CTRL = 0x18 ;
	PORTA.PIN2CTRL = 0x18 ;
	PORTA.PIN3CTRL = 0x18 ;
	PORTA.PIN4CTRL = 0x18 ;
	PORTA.PIN5CTRL = 0x18 ;
	PORTA.PIN6CTRL = 0x18 ;
	PORTA.PIN7CTRL = 0x18 ;
}

#define DEFAULT 1

uint8_t analog_reference = DEFAULT;

void analogReference(uint8_t mode)
{
	// can't actually set the register here because the default setting
	// will connect AVCC and the AREF pin, which would cause a short if
	// there's something connected to AREF.
	analog_reference = mode;
}

int analogRead(uint8_t pin)
{
	uint8_t low, high;

#if defined(analogPinToChannel)
#if defined(__AVR_ATmega32U4__)
	if (pin >= 18) pin -= 18; // allow for channel or pin numbers
#endif
	pin = analogPinToChannel(pin);
#elif defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
	if (pin >= 54) pin -= 54; // allow for channel or pin numbers
#elif defined(__AVR_ATmega32U4__)
	if (pin >= 18) pin -= 18; // allow for channel or pin numbers
#elif defined(__AVR_ATmega1284__) || defined(__AVR_ATmega1284P__) || defined(__AVR_ATmega644__) || defined(__AVR_ATmega644A__) || defined(__AVR_ATmega644P__) || defined(__AVR_ATmega644PA__)
	if (pin >= 24) pin -= 24; // allow for channel or pin numbers
#else
	if (pin >= 14) pin -= 14; // allow for channel or pin numbers
#endif

#if defined(ADCSRB) && defined(MUX5)
	// the MUX5 bit of ADCSRB selects whether we're reading from channels
	// 0 to 7 (MUX5 low) or 8 to 15 (MUX5 high).
	ADCSRB = (ADCSRB & ~(1 << MUX5)) | (((pin >> 3) & 0x01) << MUX5);
#endif
  
	// set the analog reference (high two bits of ADMUX) and select the
	// channel (low 4 bits).  this also sets ADLAR (left-adjust result)
	// to 0 (the default).
#if defined(ADMUX)
	ADMUX = (analog_reference << 6) | (pin & 0x07);
#endif

	// without a delay, we seem to read from the wrong channel
	//delayMilliseconds(1);

#if defined(ADCSRA) && defined(ADCL)
	// start the conversion
	sbi(ADCSRA, ADSC);

	// ADSC is cleared when the conversion finishes
	while (bit_is_set(ADCSRA, ADSC));

	// we have to read ADCL first; doing so locks both ADCL
	// and ADCH until ADCH is read.  reading ADCL second would
	// cause the results of each conversion to be discarded,
	// as ADCL and ADCH would be locked when it completed.
	low  = ADCL;
	high = ADCH;
#else
	// we dont have an ADC, return 0
	low  = 0;
	high = 0;
#endif

	// combine the two bytes
	return (high << 8) | low;
}




void A7105_Reset()
{
}
void CC2500_Reset()
{
}
void NRF24L01_Reset()
{
}


#include "Multiprotocol.ino"

#include "cyrf6936_SPI.ino"
#include "DSM2_cyrf6936.ino"
#include "Devo_cyrf6936.ino"

#include "Telemetry.ino"


int main(void)
{
	init() ;
	setup() ;
	for(;;)
	{
		loop() ;
	}
}